Yamaha SWX2320-16MT Manual de usuario
L2 Switch
Commutateur Réseau L2
Switch L2
Коммутатор Второго Уровня
ߗل
-큲퓒
Read This First
Folgendes zuerst lesen
À lire en premier
Leer primero este documento
Leia Isto Primeiro
Leggere prima dell’uso
Прочитайте в первую очередь
请首先阅读
ḽ䏦曆䚣
젊헎핋펂훊킻킪폲
SWX2320-16MT
KO
TW
IT
RU
ZH
PT
ES
FR
DE
EN
EnglishDeutschFrançaisEspañolPortuguêsItalianoРусскийㆶ։ѣᮽ䳿榒ᳫ㑅묻펂
2SWX2320-16MT
Protecting the environment
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the
product.
2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality
shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to use this product in the USA.
3. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and, if notinstalled and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
COMPLIANCE INFORMATION STATEMENT
(Supplier’s declaration of conformity procedure)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : L2 SWITCH
Model Name : SWX2320-16MT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference receivedincluding interference
that may cause undesired operation.
English
SWX2320-16MT 3
PRECAUTIONS
Please read these precautions carefully before proceeding.
Be sure to follow the
instructions
Please carefully read and observe the following precautions
to avoid injury or damage to your assets.
After reading this document thoroughly, please retain it in a
location that anyone using the product can access at any
time.
These precautions alert you to the possibility of
death or serious injury to you or others.
If you notice any abnormality
• If any of the following abnormalities occur, immediately
shut down the power.
- The power cord or plug becomes damaged.
- Unusual smells, noise or smoke are emitted from the
product.
- An object or some water has been dropped into the
product.
-Cracksorotherdamageappear on the product.
- The cooling fan has stopped.
Follow the steps below to shut down the power.
- Disconnect the power cord plug from the AC outlet.
Continuing to use the product as-is may result in fire,
electrical shock or malfunction. Request a check-up or
repair immediately.
Power supply
• Do not damage the power cord.
- Do not place the power cord near heat sources such as
heaters.
- Do not forcefully bend or modify the power cord.
-Donotdamagethepowercord.
- Do not place heavy objects on the power cord.
-Donotstaplethepowercord.
Using a frayed power cord with the core wire exposed may
result in fire, electrical shock or malfunction.
• During lightning or electrical storms, do not touch this
product, power plug or power cord.
Otherwise, electrical shock may be caused.
• Use the voltage specified for this product.
Using an incorrect voltage may result in fire, electrical
shock or malfunction.
• Be sure to use only the item listed below to supply power:
Otherwise, fire, burns or malfunction may be caused.
• Do not use the following Included accessories with other
devices.
-Powercord
Otherwise, fire, burns or malfunction may be caused.
• Check the power cord plug periodically and remove any
dirt or dust that may have accumulated.
Otherwise, fire or electrical shock may be caused.
• Be sure to fully insert the power cord plug into an AC
outlet.
Otherwise, electrical shock, or fire or malfunction due to
short circuit may be caused.
• Insert the power cord plug into the AC outlet that is visible
and easily accessible.
• If you plan not to use the unit for a long period of time,
remove the power cord plug from the AC outlets.
Otherwise, fire or malfunction may be caused.
Connections
• Insert the power cord plug into an appropriate AC outlet
that features a protective grounding connection.
If the device is not grounded correctly, electrical shock,
fire or malfunction may be caused.
Do not disassemble
• Do not modify or disassemble this product.
Otherwise, fire, electrical shock, injury or malfunction
may be caused.
Water warning
• Do not use this product in damp or wet conditions, such as
a bathroom or rainy outdoor location.
If liquid spills into the product, fire, electrical shock or
malfunction may be caused.
• Do not place on this product any containers (such as vases
or medicine bottles) that contain liquids.
If liquid spills into the product, fire, electrical shock or
malfunction may be caused.
• Do not insert the power cord plug into or remove it from
the AC outlet with wet hands. Do not handle this product
with wet hands.
Otherwise, electrical shock or malfunction may be caused.
• Contact the following customer center for a check-up
or repair.
- The store you purchased the product
- Yamaha dealer
• This product is intended for use as general office
equipment. Do not use it in any fields requiring a high
degree of reliability in relation to human lives.
• Please note that Yamaha cannot accept any liability
for any losses resulting from improper use or
unauthorized modification of the product.
WARNING
4SWX2320-16MT
Fire warning
• Do not handle open flames near this product.
Otherwise, fire may be caused.
Handling
• Do not drop this product or apply any strong impact to the
product.
Otherwise, fire, electrical shock or malfunction may be
caused.
Backup battery
• Do not replace the backup battery by yourself.
Doing so may cause an explosion or malfunction of the
product. If the battery needs to be replaced, contact your
Yamaha dealer and ask qualified Yamaha service
personnel to replace the battery.
These precautions alert the user to the possibility
of physical injury.
Power supply
• If the power cord plug inserted into the AC outlet is wiggly
or loose, do not use that outlet.
Otherwise, fire, electrical shock or burns may be caused.
• When removing the power cord plug from the product or
an outlet, always hold the plug itself and not the cord.
Otherwise, the power cord may be damaged, resulting in
fire or electrical shock.
Installation
• Do not place this product in an unstable position or a
location subject to vibration.
Otherwise, the product may fall or tip over, resulting in
injuries, malfunction or damage.
• Do not block the heat dissipation of this product when
installing it.
- Do not cover the product with a cloth or table cloth.
- Do not install the product on a carpet or rug.
- Do not block the vents (holes for taking in outside air,
heat dissipation and fan exhaust).
- Do not use the product in a confined, poorly-ventilated
location.
Inadequate ventilation may result in overheating inside
the product, possibly causing fire or malfunction.
• Install this product in accordance with the instructions
described in the following manual.
- User Guide (on our website)
• Inadequate ventilation may result in the product
internally overheating, possibly causing fire or
malfunction, and may also cause the product to fall or tip
over, resulting in injury, malfunction or damage.
• Do not stack this product on top of or under other devices,
since doing so may cause fire or burns.
• Do not install the product in a place where it may come
into contact with salt air, corrosive gases, oily fume or
steam.
Otherwise, the product may fall or tip over, resulting in
injuries, malfunction or damage.
• Before moving this product, be sure to remove all
connected cables.
Otherwise, the cables might be caught by a foot or hand,
and the product may fall or tip over, resulting in injuries,
malfunction or damage.
• When mounting on a wall, ceiling or rack be sure to have
someone with specialized knowledge install the product.
If necessary, ask the store where you purchased the
product or a specialized construction company.
Improper installation may cause injuries, damage, or
malfunction of this product.
• When installing horizontally, be sure to attach rubber feet.
Failing to do so may cause fire or burns.
Connections
• If you plan to connect external devices, first read the
owner’s manual for each device, and connect them in
accordance with the instructions.
If you do not follow the instructions correctly, injury or
malfunction may be caused.
Maintenance
• Before cleaning the product, be sure to remove the power
cord plug from the AC outlet.
Otherwise, electrical shock may be caused.
Handling
• Do not insert your hands or fingers in any gaps on this
product.
Otherwise, injury may be caused.
• Do not drop a foreign object, such as a piece of metal or
paper, into any gap on this product.
Otherwise, fire, electrical shock or malfunction may be
caused.
• Keep small parts away from infants.
Otherwise, they may swallow them by accident.
• Do not apply the following excessive force to this product.
- Resting your weight on this product
- Placing heavy objects on this product
- Stacking up this product
- Applying excessive force to the buttons or I/Oconnectors
- Hanging on to this product
- Leaning against this product
Otherwise, injury, electrical shock, malfunction or
damage may be caused.
• Do not pull connected cables.
Otherwise, the product may fall or tip over, resulting in
injuries, malfunction or damage.
CAUTION
English
SWX2320-16MT 5
Precautions for use
NOTICE
Follow the precautions below to avoid malfunction and
damage to this product and to prevent the loss of data.
Installation
•Ifyouhearnoise,changethe product location or
orientation, or the surrounding environment. Depending
on the environment in which you use the product, a
phone, radio or TV may generate noise.
• Do not install this product in a place subject to:
- Direct sunlight
- Extremely high or low temperatures
- Excessive dust
Otherwise, malfunction, deformation or disfiguration may
be caused.
• Do not install this product in a place where condensation
can form due to rapid, drastic changes in ambient
temperature. Using the product while condensation is
present may cause malfunction. If there is a reason to
believe that condensation might have occurred on or in
this product, leave it for several hours without turning on
the power. You can start using the product when the
condensation has completely dried.
• Do not install this product in a place subject to strong
electro-magnetic waves. Otherwise, malfunction may be
caused.
• Do not install telecommunication cables near the power
cord. Otherwise, high voltage maybe induced, resulting in
malfunction.
• Do not install using a wall mount kit or rack mount kit
other than the included items.
Connections
• Do not connect this product to a public Wi-Fi and/or
Internet service directly. Only connect this product to the
Internet through a router with strong password
protections. Consult your router manufacturer for
information on optimum security practices.
• Do not connect any noise generating devices to the same
power supply line as this product. Doing so may cause
damage or malfunctions.
• If you plan to use this product on a 1000BASE-T /
2.5GBASE-T / 5GBASE-T network, use LAN cables of
Enhanced Category 5 (CAT5e) or higher. If you plan to use
this product on a 10GBASE-T network, use cables of
Category 6 (CAT6) or higher. However, if you plan to use
this product on a 2.5GBASE-T / 5GBASET / 10GBASE-T
network, the resulting maximum transmission distance
may be shorter than the standard value due to the
influence of adjacent cables and external noise.
For details, refer to the "User Guide" on the Yamaha
website.
• When connecting using a Direct Attach cable or an STP
cable, make sure that the grounding for the devices is at
the same potential.
Handling
• Do not place any vinyl, plastic or rubber products on this
product.
Otherwise, the panel may be discolored or deteriorate.
• Before you touch this product, remove static electricity
from your body or clothing.
Otherwise, static electricity may lead to malfunction of
the product.
• Do not touch the inside of the terminal with your finger or
a metal object.
Doing so may result in malfunction or poor contact.
• Be sure to read the user guide for this product on the
website, and then only connectthe specified SFP modules
(class 1 laser; sold separately) or Direct Attach cables (sold
separately) to the SFP+ port. Operation cannot be
guaranteed if any SFP module or Direct Attach cable other
than those specified is connected.
• Attach the dust cover to SFP+ ports that are not in use.
Failing to do so could allow foreign objects to enter,
causing malfunctions. Keep the dust cover in a safe place
so that it is not lost.
• If it is difficult to pull out the Direct Attach cable (sold
separately), refer to the User Guide (available from the
website) to disconnect it. Forcibly pulling out the cable
may damage this product or the Direct Attach cable.
Maintenance
• Use a dry, soft cloth to clean this product. Do not use
benzine, thinner, detergent or chemical rag to clean the
surface of the product. Otherwise, the surface may be
discolored or deteriorate.
Disposal or transfer
• Before you transfer ownership or dispose of this product,
initialize the product settings to default. If you transfer
ownership or dispose of this product without initializing
the settings, your personal data may be stolen by a third
party.
6SWX2320-16MT
Important
information
NOTE
This section describes precautions to be observed during
use, functional restrictions, and supplemental information
that may be helpful for you.
Product features
• Yamaha continuously makes improvements and updates
to the software included in this product. You can
download the latest software from the Yamaha website.
• Use certified Optical Fiber Transceiver Class I Laser
Product.
Contents of this document
• The illustrations as shown in this document are for
instructional purposes only.
• The company names and product names in this document
are the trademarks and registered trademarks of their
respective companies.
• The contents of this document apply to the latest
specifications as of the publishing date. You can
download the latest version from the Yamaha website.
• Unauthorized copying of this document in part or in its
entirety is prohibited.
Open-source software used by this product
Visit the following website for the relevant license
agreement.
http://www.yamahaproaudio.com/
Disposal or transfer
• If you plan to transfer ownership of this product, include
this document and the supplied accessories along with
the unit.
• Follow the rules of your local authority to dispose of this
product and its accessories.
• Follow the rules of your local authority to dispose of used
batteries. This product uses a lithium battery to back up
the power for the clock function.
Nameplate of this product
This is a class A product. Operation of this product in a
residential environment could cause radio interference.
Product information, such as the model name (product
number), manufacturing number (serial number), and
power requirements, is displayed on or in the vicinity of
the nameplate on the product (top panel). We
recommend that you fill in the following space with the
model name and serial number, and store this
document in a safe place so that the information will
help you identify your product in case you lose the
product.
Model Name
Serial Number
English
Introduction
SWX2320-16MT 7
Introduction
Thank you for purchasing this Yamaha product.
• Be sure to first read the separate “Precautions”.
• For correct and safe use of this product, be sure to observe the warnings and cautions in
this manual.
• Please retain this manual in a safe location so that it is not lost.
Optional accessories, User Guide, Command Reference and technical data
are available on the Yamaha website.
http://www.yamahaproaudio.com/
Verify that the following included items are present.
• Read This First (this document)
•Powercord
• Power cord clamp (used only for the included dedicated power cord)
• Dust covers (pre-installed on the SFP+ ports when the product is shipped): 4 pcs.
• Legs (rubber feet): 4 pcs.
• 19-inch rack mount hardware: 2 pcs.
• Wall mount hardware: 2 pcs.
• Screws (M3 x 8L): 8 pcs.
Note
The screw thread diameter is 3.0 mm, the screw head diameter is 5.5 mm, and the screw
length is 8.0 mm.
Details are provided on the website.
Be sure to read the instruction manuals for other products and the User Guide for this product
before use.
Website information
Included items
Separately sold items
Introduction
8SWX2320-16MT
The following manuals are prepared according to the intended use of this product.
Read the appropriate manual according to your particular application.
• Read This First (this document)
Describes the precautions for using this product. Be sure to read before use.
• User Guide (website)
Describes how to install, connect, and set this product and other options.
• Command reference (website)
Describes the command format for setting up this product and a usage example.
• Technical reference (website)
Describes detailed information about the features of this product.
• Help for “Web Settings Screen”
Describes detailed explanations about each setting item.
Related software and documents
English
Controls and Connectors
SWX2320-16MT 9
Controls and Connectors
Note
The many holes on the front are a cooling vent for taking in outside air.
1POWER indicator
Lights when power is provided to the unit.
2mini-USB CONSOLE port
This is a mini-USB port for making settings. Use a USB cable to connect it to the USB port
of a computer.
3RJ-45 CONSOLE port
This is an RJ-45 port for making settings. Use an RJ-45/DB-9 console cable to connect it
to the RS-232C connector (COM port) of the computer.
4microSD indicator
Indicates the connection and usage status of the microSD card.
5microSD slot
A microSD card can be inserted in this slot.
6LAN ports
These ports support 100BASE-TX, 1000BASE-T, 2.5GBASE-T, 5GBASE-T, and
10GBASE-T.
7SFP+ ports
These ports support 1000BASE-SX, 1000BASE-LX, 10GBASE-SR, and 10GBASE-LR.
Install the SFP module (sold separately) and direct attach cable (sold separately).
8Stack ID indicator
This is a 7-segment display that indicates the stack ID when stack connection is used.
Front panel
①
②③④⑤ ⑦ ⑧
⑥
Controls and Connectors
10 SWX2320-16MT
9Rubber foot attachment guides
These are the locations where the rubber feet are to be attached when placing the unit on
a level surface.
0Wall mount accessory attachment holes
These are screw holes for attaching the included wall mount accessory when installing on
a wall or ceiling.
Bottom panel
9
9
00
Otros manuales para SWX2320-16MT
1
Tabla de contenidos
Idiomas:
Otros manuales de Cambiar de Yamaha
Yamaha
Yamaha SFP-SWRG-SX Manual de usuario
Yamaha
Yamaha SWX2200-8G Manual de usuario
Yamaha
Yamaha DCH8 Manual de usuario
Yamaha
Yamaha EKS Manual de usuario
Yamaha
Yamaha L2 Manual de instalación
Yamaha
Yamaha SWP1-8 Manual de usuario
Yamaha
Yamaha SWP2 Manual de usuario
Yamaha
Yamaha SWR2310-28GT Manual de usuario
Yamaha
Yamaha AVS-700 Manual de usuario
Yamaha
Yamaha SWR2100P-10G Manual de usuario
