Yamaha Studio Manager V2 DM2000 Editor Guía de configuración

Cubase SX3 / DM2000 V2 Setup and Operation Page 1

Cubase SX3 / DM2000 V2 Setup and Operation

This document describes setup and operation for remote control of Cubase SX from the

DM2000 digital mixing console. These instructions apply to DM2000 V2.0 or higher

and Cubase SX V3.0.0 or higher.

Driver Installation

1) Connect your PC or Macintosh computer

The DM2000 should be connected to your computer by connecting the TO HOST

USB port on the DM2000 to a USB port on your computer.

2) Install Driver

Once your computer is connected, you will need to install the USB-MIDI driver

included on the DM2000 CD-ROM. It is recommended that you install the latest

driver which can be downloaded from www.yamahaproaudio.com

Configuring DM2000 V2

1) Press the [SETUP] display access key and select the MIDI/TO HOST screen.

2) Set the DAW port assignment to USB 2-5 (this allows USB port 1 to be used for

the DM2000 Studio Manager Editor software). Note: you must use USB ports 2-

5 for DAW Control and USB port 1 for Studio Manager if you intend to use these

two applications simultaneously.

3) Press the [REMOTE] display access key and assign CUBASE SX as the Target

for one of the Remote layers.

(See “About Remote Layers” in the DM2000 manual for more information.)

4) Press the [LOCATOR] display access key and select DAW Control as the

function for the transport and locate keys. This allows the Cubase SX transport to

be controlled regardless of whether a Remote or Internal mixing layer is active.

5) Press the relevant [REMOTE] LAYER button to select the Cubase SX Remote

Control Layer.

When the Cubase SX Remote Control Layer is selected, the DM2000’s control

surface controls Cubase SX rather than the internal mixing of the DM2000. In

order to control the DM2000, you need to select an Input Channel Layer or the

Master Layer. Audio mixing on the Input and Master Layers, and Automix

continues while the Cubase SX Layer is selected.

Cubase SX3 / DM2000 V2 Setup and Operation Page 2

Configuring Cubase SX V3.0.0 or higher

1) Click on the ‘Devices’ menu and select ‘Device Setup’.

2) Click on the ‘+’ icon (Add Device), then click on ‘Yamaha DM2000 V2’. This

will cause Yamaha DM2000 V2 to appear in the Devices column on the left side

of this window.

3) In the right side of the ‘Device Setup’ window, assign DM2000 V2 to the correct

MIDI Input and Output ports. For example, if you have chosen USB 2-5 on

DM2000, choose ‘YAMAHA USB 0-2’ in Windows XP/2000 systems (choose

‘YAMAHA DM1000 Port2’ in Mac OS X). Then select the same port number

for MIDI Output. This will cause USB ports 2 through 5 to be assigned for

remote control of Cubase SX from DM2000.

4) In the grid below the MIDI port assignments, the functions of various USER

DEFINED keys on the DM2000 can be assigned. Some USER DEFINED keys

have permanent assignments so they are not available in this list. These functions

are described later in this document.

5) After completing these assignments, click ‘Apply’ towards the bottom of the

Device Setup window. Then click ‘OK’ to exit this window.

Controlling Cubase SX

Input Channel Controls

Faders 1-24 control the levels of Cubase SX channels 1-24.

(Refer to the User Defined Keys description below for information about accessing

Cubase SX channels beyond 1-24.)

The first four characters of the names of the Cubase SX channels appear in the

Fluorescent channel strip display. Also PAN position is displayed here and can be

adjusted with each channel’s rotary encoder. For surround panning, pressing the PAN

ENCODER MODE switch alternates the function of the encoder between Left-Right and

Front-Back panning. When the encoder is functioning in PAN mode, pushing the

encoder will activate the MONITOR switch in Cubase SX.

The DM2000 ON switches control each Cubase SX channel’s MUTE, and the SOLO and

SEL switches also control Cubase SX’s corresponding functions. The AUTO switches

on DM2000 control Cubase SX’s Automation Read function.

By changing the DM2000’s ENCODER MODE to AUX/MTRX, Cubase SX’s SENDS

can be controlled. Sends 1-8 can be selected with the DM2000’s AUX SELECT

switches. Then turning the channel rotary encoders will adjust the send level, with the

Cubase SX3 / DM2000 V2 Setup and Operation Page 3

level shown in the fluorescent display section. In this mode, each send can be switched

On/Off by pressing the encoder.

Selected Channel Functions

Pressing any of the DISPLAY switches in the SELECTED CHANNEL section of

DM2000 will cause the VST Audio Channel Settings window to open in Cubase SX.

COPY & PASTE

The CHANNEL COPY and PASTE switches on DM2000 perform the same functions as

COPY and PASTE in Cubase SX’s Edit menu.

The four bands of EQ GAIN, FREQUENCY and Q on DM2000 control the same

functions on the selected Cubase SX channel, and the parameter value is displayed on the

console. To switch an EQ band On or Off, hold down the FREQUENCY/Q encoder for

one second.

The entire EQ section can be bypassed by pressing the EQ ON key in the SELECTED

CHANNEL section of DM2000. (Note: when the EQ ON LED is lit in the DM2000, this

indicates EQ Bypass in Cubase SX.)

PANNING

The PAN encoder and the JOYSTICK on DM2000 control the pan functions of Cubase

SX. Even if there is no surround panning enabled, the joystick can be used for Left-Right

panning.

AUX SENDS

The AUX SEND LEVEL encoders and ON switches edit the 8 sends in Cubase SX. So

only the first two BANKS on DM2000 are used. By pressing the LEVEL encoders, the

send can be switched between Pre and Post Fader.

PHASE AND INSERT

The PHASE switch on DM2000 switches the phase of the selected Cubase SX channel,

and the INSERT ON switch bypasses all Inserts for the selected channel.

Cubase SX3 / DM2000 V2 Setup and Operation Page 4

FX Sends, Routing and Insert Editing

FX SENDS

In the EFFECTS / PLUG-INS section of the DM2000, press the INTERNAL EFFECTS

key to access FX Send information on the LCD screen. The encoders below the screen

can edit various functions:

•Encoder 1 edits the send level.

•Encoder 2 edits the send On/Off status (by turning the encoder).

•Encoder 3 edits between Pre and Post Fader (by turning the encoder).

•Pressing any of the encoders will switch all sends On/Off.

There are 8 sends spread over 8 pages. To access different sends, use the UP and DOWN

cursor buttons to the left of the LCD encoders.

ROUTING

Press the PLUG-INS switch to access Routing information in the LCD. There are two

pages, accessed by pressing the UP and DOWN cursor buttons to the left of the LCD

encoders. The following functions can be edited:

Page 1

•Encoder 1 chooses the Output Bus for the selected channel

•Encoder 2 switches the Monitor On/Off (by pressing or turning the encoder)

•Encoder 3 selects the Input bus

•Encoder 4 edits the Input Gain (the encoder must be pressed down while turning)

Page 2

Only Encoder 1 has a function. It is used to switch the Input Phase On/Off (by pressing

or turning the encoder).

INSERTS

When the CHANNEL INSERTS switch is pressed on DM2000, the LCD shows Insert

information for the selected channel.

•Encoder 1 selects which insert is to be edited

•Encoder 2 switches the insert On/Off (by turning, not pressing)

•Encoder 3 selects the type of effect to insert

Once an Effect has been selected, all the parameters can be edited by changing the page

viewed on the LCD (by pressing the UP and DOWN cursor buttons to the left of the LCD

encoders). The number of pages available depends on the number of parameters used by

the Effect.

Note: in any of the above modes, the EFFECT DISPLAY switch toggles between

showing the parameter names and the parameter values on the LCD.

Cubase SX3 / DM2000 V2 Setup and Operation Page 5

Transport & Automation

Ensure that DAW CONTROL is selected in the LOCATE MEMORY screen of the

LOCATOR display menu on DM2000.

TRANSPORT CONTROLS

The following Transport functions can be controlled from DM2000:

•REC

•PLAY

•STOP

•FF

•REW

•SCRUB

•SHUTTLE

•LOOP

•QUICK PUNCH

•ONLINE

LOCATE FUNCTIONS

The following DM2000 locate functions also control the corresponding Cubase SX

functions:

•RTZ

•END

•IN

•OUT

•SET

•LOCATE 1-8

To set a locate point (Marker in Cubase SX), hold the SET switch on DM2000, and press

the required LOCATE MEMORY switch at the required time. Note: DM2000 must be in

the appropriate Cubase SX Remote Layer in order to set Markers.

TRACK-ARMING

The DM2000 TRACK ARMING 1-24 switches control the RECORD ENABLE switches

of the corresponding Cubase SX channels.

AUTOMATION

The following AUTOMIX switches on DM2000 control automation functions of Cubase

SX:

•ENABLE puts all Cubase SX channels into READ mode

•REC puts all Cubase SX channels into WRITE mode.

•The AUTO switch above each DM2000 channel fader switches READ On/Off for

each channel individually. However, when AUTO-REC is switched on, the channel

AUTO switches function to control WRITE On/Off in Cubase SX.

Cubase SX3 / DM2000 V2 Setup and Operation Page 6

User Defined Keys

When DM2000 is used to remotely control Cubase SX, the following User Defined Keys

have permanently assigned functions:

UDEF 1: Brings the Project window to the front

UDEF 2: Scrolls channels down in banks of 8

UDEF 3: Scrolls channels up in banks of 8

UDEF 9: Open or closes the VST Mixer window

UDEF 10: Scrolls channels down one channel at a time

UDEF 11: Scrolls channels up one channel at a time

Other User Defined Keys (UDEF 4-8 and 12-16) can be programmed by the user to

control various Cubase SX functions. These functions can be selected in the DEVICE

SETUP of Cubase SX, by selecting “YAMAHA DM2000 V2” and choosing the desired

‘Category’ and ‘Command’ from the drop-down list for each button.

Other Functions

ZOOM & NAVIGATION

The DM2000 CURSOR keys (next to the Scrub Wheel) have two different functions.

Their mode can be changed by pressing the INC key above the cursor keys. The mode is

shown on the LCD display.

•ZOOM mode: the cursor keys control the vertical and horizontal zoom of the Project

Window.

•NAVIGATION mode: the cursor keys control the selection of channels and objects in

the Project Window.

TIME COUNTER

The TIME COUNTER is displayed on the DM2000 LCD screen, with the counter mode

(TIME CODE / FEET / BEATS). If “Samples” is selected in Cubase SX, then no

selection is displayed in the DM2000 LCD.

METER BRIDGE

The DM2000 meter bridge displays Cubase SX’s input channel levels when the correct

REMOTE layer is selected. The TIME CODE counter is also displayed on the Meter

Bridge.

Otros manuales para Studio Manager V2 DM2000 Editor

Tabla de contenidos

Otros manuales de Mezclador de música de Yamaha

Yamaha

Yamaha DM 2000 Version 2 Manual de usuario

Yamaha

Yamaha PM2800M Manual de usuario

Yamaha

Yamaha CL5 Instrucciones y recetas

Yamaha

Yamaha RM800 Manual de usuario

Yamaha

Yamaha MM 1402 Manual de usuario

Yamaha

Yamaha MG16/6FX Manual de usuario

Yamaha

Yamaha TF5 Manual de usuario

Yamaha

Yamaha PM5D Manual de usuario

Yamaha

Yamaha n8 Manual de usuario

Yamaha

Yamaha CL5 Manual de usuario

Yamaha

Yamaha 007POTO-G0 Manual de usuario

Yamaha

Yamaha MW10 Manual de usuario

Yamaha

Yamaha MG206C Instrucciones de montaje

Yamaha

Yamaha IM8-40 Manual de usuario

Yamaha

Yamaha MIXING CONSOLE Manual de usuario

Yamaha

Yamaha AM802 Manual de usuario

Yamaha

Yamaha DJX-IIB Manual de usuario

Yamaha

Yamaha AG06 Manual de usuario

Yamaha

Yamaha MG166C-USB Manual de usuario

Yamaha

Yamaha MV12 Manual de usuario

Yamaha

Yamaha PM3500M Manual de usuario

Yamaha

Yamaha EMX 2000 Manual de usuario

Yamaha

Yamaha MG 06 X Manual de usuario

Yamaha

Yamaha M7CL-48ES Manual de usuario

Manuales populares de Mezclador de música de otras marcas

Neve

Neve 8816 Manual de usuario

Mackie

Mackie Onyx Analogue Mixer Manual de usuario

Behringer

Behringer EUROPOWER PMP518M Manual de usuario

Peavey

Peavey S-32 Sanctuary Series Manual de usuario

Rane

Rane MP 4 Manual de usuario

True

True T9 Touchscreen Console Manual de usuario

Studiomaster

Studiomaster Air Pro 24 Manual de usuario

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Manual de usuario

Roland

Roland M-160 Manual de usuario

Ecler

Ecler MAC40v Manual de usuario

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Manual de usuario

Veeder-Root

Veeder-Root TLS-350 Series Manual de usuario

Alto

Alto APM80.QUAD Manual de usuario

Omnitronic

Omnitronic PM-211 Manual de usuario

SoundCraft

SoundCraft B400 Manual de usuario

Roland

Roland SoundCanvas SC-8820 Manual de usuario

CARVIN

CARVIN RX 1200 Manual de usuario

Roland

Roland M-16E Manual de usuario