Yamaha DM 1000 Manual de usuario

DM1000/MB1000/SP1000

SERVICE MANUAL

PA 011681

1.329K-6554 Printed in Japan ’03.03

HAMAMATSU, JAPAN

This document is printed on chlorine free (ECF) paper with soy ink.

DIGITAL PRODUCTION CONSOLE/

PEAK METER BRIDGE/WOODEN SIDE PANELS

/MB1000/SP1000

CONTENTS

SPECIFICATIONS ................................................... 4

DIMENSIONS .......................................................... 13

PANEL LAYOUT .................................. 14

CIRCUIT BOARD LAYOUT ............... 23

DISASSEMBLY PROCEDURE ............................ 28

INSTALLING AN OPTIONAL CARD

............................................ 46

LSI PIN DESCRIPTION ................................ 47

IC BLOCK DIAGRAM .................................. 58

CIRCUIT BOARDS ....................................... 65

INSPECTIONS ...................................................103/109

DM1000/MB1000 SERVICE CHECK PROGRAM

..................115/129

MB1000 TEST PROGRAM ........................................143/144

INITIALIZING THE DM1000 ................. 145

TRANSMITTING PARAMETER SETTINGS VIA MIDI (BULK DUMP)

....146/148

CHECKING THE BATTERY AND THE SYSTEM VERSION

.......... 150

CALIBRATING THE FADERS ................................... 150

MIDI DATA FORMAT ............... 151

MIDI IMPLEMENTATION CHART ............................ 166

PARTS LIST

BLOCK DIAGRAM

OVERALL CONNECTOR CIRCUIT DIAGRAM

CIRCUIT DIAGRAM

このサービスマニュアルはエコパルプ

（ECF：無塩素系漂白パルプ）を使用しています。

このサービスマニュアルは大豆油

インクで印刷しています。

DM1000: 200303-600000

MB1000: 200303-105000

SP1000: 200303-35000

（目次）

（

総合仕様

）

（寸法図）

（パネルレイアウト）

（ユニットレイアウト）

（分解手順）

（オプションカードの取り付け）

（LSI端子機能表）

（ICブロック図）

（シート基板図）

（検査）

（DM1000/MB1000サービス検査プログラム）

（MB1000テストプログラム）

（DM1000の初期化）

（内部設定をMIDI経由で出力（バルクダンプ機能））

（バッテリーの残量やシステムのバージョンの確認）

（フェーダーのキャリブレーション）

（MIDIデータフォーマット）

（MIDIインプリメンテーションチャート）

（ブロックダイアグラム）

（総コネクタ接続回路図）

（回路図）

DM1000/MB1000/SP1000

IMPORTANT NOTICE

This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed

that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under-

stood by the users, and have therefore not been restated.

WARNING : Failure to follow appropriate service and safety procedures when servicing this product may result in per-

sonal injury, destruction of expensive components and failure of the product to perform as specified. For

these reasons, we advise all Yamaha product owners that all service required should be performed by an

authorized Yamaha Retailer or the appointed service representative.

IMPORTANT : This presentation or sale of this manual to any individual or firm does not constitute authorization certifi-

cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of

any form.

The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and

service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable

and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to

exist, please contact the distributor’s Service Division.

WARNING : Static discharges can destroy expensive components. Discharge any static electricity your body may have

accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to

this bus.)

IMPORTANT : Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power

to the unit.

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where

applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly

other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT

SO EVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose

eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling

food.

WARNING

Components having special characteristics are marked and must be replaced with parts having specification equal to those

originally installed.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be

connected to the terminal in the plug which is marked by the letter E

or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

印の商品は、安全を維持するために重要な部品です。交換する場合は、安全のために必ず指定の部品をご使用下さい。

DM1000/MB1000/SP1000

Take care not to trap your fingers.

LITHIUM BATTERY HANDLING

This product uses a lithium battery for memory back-up.

WARNING : Lithium batteries are dangerous because they can be exploded by improper handling. Observe the following pre-

cautions when handling or replacing lithium batteries.

Leave lithium battery replacement to qualified service personnel.

Always replace with batteries of the same type.

When installing on the PC board by soldering, solder using the connection terminals provided on the battery cells.

Never solder directly to the cells. Perform the soldering as quickly as possible.

Never reverse the battery polarities when installing.

Do not short the batteries.

Do not attempt to recharge these batteries.

Do not disasemble the batteries.

Never heat batteries or throw them into fire.

ADVARSEL!

Lithiumbatteri-Eksplosionsfare ved fejlagtig handtering. Udskiftning ma kun ske med batteri af samme fabrikat og type. lever det brugte

batteri tilbage til leverandren.

VARNING

Explosionsfara vid felaktigt batteribyte.

Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera anvant batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi rajahtaa, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiiin.

Havita kaytetty paristo valmistajan ohjeiden mukaisesti.

The following information complies with Dutch official Gazette 1995. 45; ESSENTIALS OF ORDER ON THE COLLECTION OF BATTERIES.

• Please refer to the diassembly procedure for the removal of Back-up Battery.

• Leest u voor het verwijderen van de backup batterij deze beschrijving.

リチウム電池の取り扱い

＜注意＞

リチウム電池を誤って交換すると爆発する危険があります。交換する場合は、サービスマニュアルで指定された部品を

使用してください。

（作業中は指を挟まない様に注意して下さい。）

DM1000/MB1000/SP1000

SPECIFICATIONS

General Spec

Number of scene memories 99

Sampling Frequency Internal 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

External Normal rate: 44.1 kHz–10% to 48 kHz+6%

Double rate: 88.2 kHz–10% to 96 kHz+6%

Signal Delay fs=48 kHz Less than 1.6 ms CH INPUT to OMNI OUT

fs=96 kHz Less than 0.8 ms CH INPUT to OMNI OUT

Fader 100 mm motorized with touch sense x 17

Fader Resolution +10 to –138, –∞dB (1024 steps/100 mm) input faders

0 to –138, –∞dB (1024 steps/100 mm) master faders, stereo fader

Total Harmonic Distortion *

(CH INPUT to OMNI OUT)

(Input Gain=Min.)

fs=48 kHz Less than 0.05% 20 Hz to 20 kHz @ +14 dB into 600Ω

Less than 0.01% 1 kHz @ +24 dB into 600Ω

fs=96 kHz Less than 0.05% 20 Hz to 40 kHz @ +14 dB into 600 Ω

Less than 0.01% 1 kHz @ +24 dB into 600Ω

Frequency Response

(CH INPUT to OMNI OUT) fs=48 kHz 20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600Ω

fs=96 kHz 20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600Ω

Dynamic Range

(maximum level to noise level)

110 dB typ. DA Converter (OMNI OUT)

106 dB typ. AD+DA (to OMNI OUT) @ fs=48 kHz

106 dB typ. AD+DA (to OMNI OUT) @ fs=96 kHz

Hum & Noise*

(20 Hz–20 kHz)

Rs=150Ω

–128 dB Equivalent Input Noise

–86 dB residual output noise. OMNI OUT (STEREO OUT off)

Input Gain=Max.

Input Pad =0 dB –86 dB (90 dB S/N) OMNI OUT

(STEREO fader at nominal level and all CH INPUT faders at minimum level)

Input Pad =0 dB

Input Sensitivity

=–60 dB

–64 dB (68 dB S/N) OMNI OUT

(STEREO fader at nominal level and one CH INPUT fader at nominal level)

Maximum Voltage Gain 74 dB CH INPUT (CH1–16) to OMNI OUT (STEREO, BUS, AUX)

Crosstalk

(@ 1 kHz)

Input Gain=Min.

80 dB adjacent input channels (CH1–16)

80 dB input to output

AD Input (1–16)

Phantom switch +48 V DC

Pad switch 0/20 dB attenuation

Gain control 44 dB (–60 to –16), detented

Peak indicator LED (red) turns on when post HA level reaches 3 dB below clipping at dig-

ital domain

Signal indicator LED (green) turns on when post HA level reaches 20 dB below nominal at

digital domain

AD converter 24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-

sampling (fs=88.2, 96 kHz)

Analog Input

(OMNI IN 1–4) AD converter 24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-

sampling (fs=88.2, 96 kHz)

Option Input (SLOT 1–2) Available cards Optional digital interface cards (MY16, MY8, MY4 series)

Digital Input

(2TR IN DIGITAL 1–2) SRC On/off (1:3 and 3:1 maximum input to output sample rate ratio)

（総合仕様）

（一般仕様）

DM1000/MB1000/SP1000

Input Channel CH1–48

Input patch —

Phase Normal/reverse

Gate-type*3On/off

Key in: 12 ch Group (1–12, 13–24, 25–36, 37–48)/AUX1–8

Comp-type*4On/off

Key in: self /Stereo Link

Pre EQ/pre fader/post fader

Attenuator –96.0 to +12.0 dB (0.1 dB step)

EQ 4-band PEQ (TYPE1)*5

On/off

Delay 0–43400 samples

On/off —

Fader 100 mm motorized (INPUT/AUX1–8)

Aux send On/off

AUX1–8; pre fader/post fader

Solo On/off

Pre fader/after pan

Pan 127 positions (Left= 1–63, Center, Right= 1–63)

Surround pan 127 ×127 positions

[(Left= 1–63, Center, Right= 1–63)] , [(Front= 1–63, Center, Rear= 1–63)]

LFE level –∞, –96 dB to +10 dB (256 step)

Routing STEREO, BUS1–8, DIRECT OUT

Direct out Pre EQ/pre fader/post fader

Metering Displayed on LCD

Peak hold on/off

TALKBACK

Level control Analog rotary potentiometer

AD converter 24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times over-

sampling (@fs=44.1, 48 kHz)

Talkback select Built-in microphone/AD IN 1–16/OMNI IN 1–4

On/off —

OSCILLATOR

Level 0 to –96 dB (1 dB step)

On/off —

Waveform

Sine 100 Hz, sine 1 kHz, sine 10 kHz, 400 Hz/1 kHz, pink noise, burst noise

Routing BUS1–8, AUX1–8, STEREO L, R

STEREO OUT DA converter 24-bit linear, 128-times oversampling

OMNI OUT 1–12 Output patch

STEREO, BUS1–8, AUX1–8, SURROUND MONITOR, CONTROL ROOM,

DIRECT OUT 1–48, INSERT OUT (CH1–48, BUS1–8, AUX1–8, STEREO),

MONITOR MATRIX OUT, SOLO OUT, CASCADE OUT (BUS1–8, AUX 1–8,

STEREO, SOLO)

DA converter 24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times over-

sampling (@fs=44.1, 48 kHz)

2TR OUT DIGITAL 1–2

Dither On/off

Word length 16, 20, 24-bit

Output patch

STEREO, BUS1–8, AUX 1–8, CONTROL ROOM, DIRECT OUT 1–48, INSERT

OUT (CH 1–48, BUS 1–8, AUX 1–8, STEREO), SOLO OUT, CASCADE OUT

(BUS 1–8, AUX 1–8, STEREO, SOLO)

Option Output (SLOT 1–2)

Available card Optional digital interface card (MY16, MY8, MY4 series)

Output patch

STEREO, BUS1–8, AUX 1–8, SURROUND MONITOR, CONTROL ROOM,

DIRECT OUT 1–48, INSERT OUT (CH 1–48, BUS 1–8, AUX 1–8, STEREO),

MONITOR MATRIX OUT, SOLO OUT, CASCADE OUT (BUS 1–8, AUX 1–8,

STEREO, SOLO)

Dither On/off

Word length 16/20/24-bit

DM1000/MB1000/SP1000

STEREO

Comp-type*

On/off

Pre EQ/pre fader/post fader

Attenuator –96.0 to +12.0 dB (0.1 dB step)

EQ 4-band PEQ *

On/off

On/off —

Fader 100 mm motorized

Balance 127 positions (Left=1–63, Center, Right=1–63)

Delay 0–29100 samples

Metering Displayed on LCD

Peak hold on/off

32-elements x2 LED meters

BUS1–8

Comp-type*

On/off

Pre EQ/pre fader/post fader

Attenuator –96.0 to +12.0 dB (0.1 dB step)

EQ 4-band PEQ*

On/off

On/off —

Fader 100 mm motorized

Delay 0–29100 samples

Bus to stereo Level (–∞, –130 dB to 0 dB)

On/off

Pan: 127 positions (Left=1–63, Center, Right=1–63)

Metering Displayed on LCD

Peak hold on/off

AUX1–8

Comp-type*

On/off

Pre EQ/pre fader/post fader

Attenuator –96.0 to +12.0 dB (0.1 dB step)

EQ 4-band PEQ*

On/off

On/off —

Fader 100 mm motorized

Delay 0–29100 samples

Metering Displayed on LCD

Peak hold on/off

SURROUND MONITOR

Mute On/off

Solo On/off

Source BUS1–8, SLOT 1–2

Monitor to C-R On/off

Oscillator Pink noise/500–2 kHz/1 kHz

Monitor matrix 6.1→6.1, 6.1→5.1, 6.1→3-1, 6.1→ST, 5.1→5.1, 5.1→3-1, 5.1→ST,

3-1→3-1, 3-1→ST

Bass

management 5 presets

Monitor

alignment ATT (–12.0 dB to 12 dB 0.1 dB step), Delay (0–30.0 msec 0.02 msec step)

INTERNAL EFFECTS

(EFFECT 1–4)

Bypass On/off

In/out 8-in, 8-out (EFFECT1): depends on effects type

2-in, 2-out (EFFECT2–4): depends on effects type

Effect-in from AUX1–8/INSERT OUT/effect-out (out 1, 2 only)

Effect-out 1, 2 to Input patch/effect-in

DM1000/MB1000/SP1000

EQ Parameters

Gate Parameters

Power Requirements U.S./Canada 120 V, 60 Hz 135 W

Japan 100 V, 50/60 Hz 135 W

Other 220–240 V, 50/60 Hz 135 W

Dimensions (H x D x W) 200 x 585 x 436 mm (7.8" x 23.0" x 17.1")

With MB1000 and SP1000 installed: 295 x 635 x 486 mm (11.6" x 25.0" x

19.1")

Net weight 20 kg (75 lbs)

Operating free-air temperature range 10–35°C (50–95°F)

Storage temperature range –20 to 60°C (–4 to 140°F)

Supplied Accessories AC Cable (3P/2P AC plug adapter), CD-ROM (Studio Manager),

Owner’s Manual, Studio Manager Installation Guide, Warranty card (J)

Options

Digital interface card (MY16, MY8, MY4 series)

PEAK METER BRIDGE: MB1000

SIDE PANEL: SP1000

RACK MOUNT KIT: RK1

1. Total harmonic distortion is measured with a 6 dB/octave filter @ 80 kHz.

2. Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave

attenuation.

3. See “Gate Parameters” on page 7.

4. See “Comp Parameters” on page 8.

5. See “EQ Parameters” on page 7.

LOW/HPF L-MID H-MID HIGH /LPF

0.1–10.0

(41 points)

low shelving

HPF

0.1–10.0

(41 points)

0.1–10.0

(41 points)

high shelving

LPF

F21.2 Hz–20 kHz (1/12 oct step)

G±18 dB

(0.1 dB step)

HPF: on/off

±18 dB

(0.1 dB step)

±18 dB

(0.1 dB step)

LPF: on/off

Gate

Threshold –54 dB to 0 dB (0.1 dB step)

Range –70 dB to 0 dB (1 dB step)

Attack 0 ms–120 ms (1 ms step)

Hold

0.02 ms–1.96 s (216 points) @ 48 kHz

0.02 ms–2.13 s (216 points) @ 44.1 kHz

0.01 ms–981 ms (216 points) @ 96 kHz

0.01 ms–1.06 s (216 points) @ 88.2 kHz

Decay

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Ducking

Threshold –54 dB to 0 dB (0.1 dB step)

Range –70 dB to 0 dB (1 dB step)

Attack 0 ms–120 ms (1 ms step)

Hold

0.02 ms–1.96 s (216 points) @ 48 kHz

0.02 ms–2.13 s (216 points) @ 44.1 kHz

0.01 ms–981 ms (216 points) @ 96 kHz

0.01 ms–1.06 s (216 points) @ 88.2 kHz

Decay

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

（EQ パラメーター）

（Gateパラメーター）

DM1000/MB1000/SP1000

Compressor

Threshold –54 dB to 0 dB (0.1 dB step)

Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞(16 points)

Out gain 0 dB to +18 dB (0.1 dB step)

Knee Hard, 1, 2, 3, 4, 5 (6 step)

Attack 0 ms–120 ms (1 ms step)

Release

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Expander

Threshold –54 dB to 0 dB (0.1 dB step)

Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞(16 points)

Out gain 0 dB to +18 dB (0.1 dB step)

Knee Hard, 1, 2, 3, 4, 5 (6 points)

Attack 0 ms–120 ms (1 ms step)

Release

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Compander H

Threshold –54 dB to 0 dB (0.1 dB step)

Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points)

Out gain –18 dB to 0 dB (0.1 dB step)

Width 1 dB–90 dB (1 dB step)

Attack 0 ms–120 ms (1 ms step)

Release

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Compander S

Threshold –54 dB to 0 dB (0.1 dB step)

Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points)

Out gain –18 dB to 0 dB (0.1 dB step)

Width 1 dB–90 dB (1 dB step)

Attack 0 ms–120 ms (1 ms step)

Release

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Comp Parameters

（Compパラメーター）

DM1000/MB1000/SP1000

In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.

Allinput AD converters (INPUT 1–16,OMNIINPUT 1–4, TALKBACK) are 24-bitlinear,128-times oversampling. (@fs=44.1,

48 kHz)

+48 V DC (phantom power) is supplied to CH INPUT (1–16) XLR type connectors via individual switches.

In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.

All output DA converters

(

OMINI OUT 1–12, PHONES

)

are 24-bit, 128-times oversamplin

(

@fs=44.1, 48 kHz

)

Effect library (EFFECT 1–4) Presets 52 (EFFECT 2–4: 44)

User memories 76

Compressor library Presets 36

User memories 92

Gate library Presets 4

User memories 124

EQ library Presets 40

User memories 160

Channel library Presets 2

User memories 127

Surround Monitor library Presets 1

User memories 32

Input patch library Presets 1

User memories 32

Output patch library Presets 1

User memories 32

Bus to Stereo library Presets 1

User memories 32

Input PAD GAIN Actual Load

Impedance For Use With

Nominal

Input level Connector

Sensitivity*

1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit

is set to maximum gain. (All faders and level controls are maximum position.)

Nominal Max.

before clip

INPUT 1–16 0–60 dB

3k Ω50–600 Ω

Mics & 600 Ω

Lines

–70 dB

(0.245 mV) –60 dB

(0.775 mV) –40 dB

(7.75 mV)

XLR-3-31 type

(Balanced)*

2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).

–16 dB

–26 dB

(38.8 mV) –16 dB

(0.123 V) +4 dB

(1.23 V)

20 –6 dB

(338 mV) +4 dB

(1.23 V) +24 dB

(12.28 V)

OMNI IN 1–4 — 10k Ω600 ΩLines +4 dB

(1.23 V) +4 dB

(1.23 V) +24 dB

(12.28 V)

Output Actual

Source

Impedance

For Use With

Nominal

Output level Connector

Nominal Max.

before clip

OMNI OUT 1–12 150 Ω600 ΩLines +4 dB

(1.23 V) +24 dB

(12.28 V) XLR-3-32 type (Balanced)*

1. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).

PHONES 100 Ω8 ΩPhones 4 mW 25 mW Stereo Phone Jack (TRS)

(Unbalanced)

2. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND).

Ω

Phones

12 mW 75 mW

Libraries

Analog Input Spec

Analog Output Spec

（ライブラリー）

（アナログ入力仕様）

（アナログ出力仕様）

DM1000/MB1000/SP1000

Input Format Data length Level Connector

2TR IN DIGITAL 1AES/EBU 24-bit RS422 XLR-3-31 type (Balanced)*

1. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).

2IEC-60958 24-bit 0.5 Vpp/75 ΩPhono

Output Format Data length Level Connector

2TR OUT DIGITAL 1AES/EBU *

Professional use

1. Channel status of 2TR OUT DIGITAL 1

Type: linear PCM

Emphasis: NO

Sampling rate: depends on the internal configuration

24-bit*

2. Dither: word length 16/20/24 bit

RS422 XLR-3-32 type

(Balanced)*

3. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).

2IEC-60958*

Consumer use

4. Channel status of 2TR OUT DIGITAL 2

Type: linear PCM

Category code: Digital signal mixer

Copy prohibit: NO

Emphasis: NO

Clock accuracy:Level II (1000 ppm)

Samplin

rate: depends on the internal confi

uration

24-bit*

0.5V pp/75 ΩPhono

Digital Input Spec

Digital Output Spec

（デジタル入力仕様）

（デジタル出力仕様）

Otros manuales para DM 1000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mezclador de música de Yamaha

Yamaha

Yamaha MG8/2FX Manual de usuario

Yamaha

Yamaha PM5D Manual de usuario

Yamaha

Yamaha 02R96 Version 2 Manual de usuario

Yamaha

Yamaha DM 2000 Version 2 Manual de usuario

Yamaha

Yamaha EMX66M Guía de configuración

Yamaha

Yamaha EM-1620 Manual de usuario

Yamaha

Yamaha EMX2 Manual de usuario

Yamaha

Yamaha MG102Cc Manual de usuario

Yamaha

Yamaha AI8-ML8F Manual de usuario

Yamaha

Yamaha SB168-ES Manual de usuario

Yamaha

Yamaha PM5D Manual de usuario

Yamaha

Yamaha DM 1000 Manual

Yamaha

Yamaha LS9 Editor Manual de usuario

Yamaha

Yamaha EMX3500 Manual de usuario

Yamaha

Yamaha M7CL StageMix V1.5 Instrucciones y recetas

Yamaha

Yamaha RIVAGE PM3 CS-R3 Manual de usuario

Yamaha

Yamaha DMR8 v.3.0 Manual de usuario

Yamaha

Yamaha MG102C - 10 Input Stereo Mixer Manual de usuario

Yamaha

Yamaha M2500 Manual de usuario

Yamaha

Yamaha DME4IO-C Manual de usuario

Yamaha

Yamaha MG124C Manual de usuario

Yamaha

Yamaha UW500Plus Manual de usuario

Yamaha

Yamaha Ncs500-FD Manual de usuario

Yamaha

Yamaha NUAGE Manual de usuario

Manuales populares de Mezclador de música de otras marcas

Neve

Neve 8816 Manual de usuario

Mackie

Mackie Onyx Analogue Mixer Manual de usuario

Behringer

Behringer EUROPOWER PMP518M Manual de usuario

Peavey

Peavey S-32 Sanctuary Series Manual de usuario

Rane

Rane MP 4 Manual de usuario

True

True T9 Touchscreen Console Manual de usuario

Studiomaster

Studiomaster Air Pro 24 Manual de usuario

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Manual de usuario

Roland

Roland M-160 Manual de usuario

Ecler

Ecler MAC40v Manual de usuario

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Manual de usuario

Veeder-Root

Veeder-Root TLS-350 Series Manual de usuario

Alto

Alto APM80.QUAD Manual de usuario

Omnitronic

Omnitronic PM-211 Manual de usuario

SoundCraft

SoundCraft B400 Manual de usuario

Roland

Roland SoundCanvas SC-8820 Manual de usuario

CARVIN

CARVIN RX 1200 Manual de usuario

Roland

Roland M-16E Manual de usuario