Yamaha 01V96 Manual de usuario

01V96

SERVICE MANUAL

PA 011680

1.329K-1933 Printed in Japan ’03.03

HAMAMATSU, JAPAN

CONTENTS

SPECIFICATIONS ................................................... 4

DIMENSIONS .......................................................... 12

PANEL LAYOUT .................................. 13

CIRCUIT BOARD LAYOUT ............... 21

DISASSEMBLY PROCEDURE ............................ 23

INSTALLING AN OPTIONAL CARD

............................................ 32

LSI PIN DESCRIPTION ................................ 33

IC BLOCK DIAGRAM .................................. 41

CIRCUIT BOARDS ....................................... 46

INSPECTIONS .......................................................76/83

SERVICE CHECK PROGRAM

...90/102

INITIALIZING THE 01V96 ....................... 114

TRANSMITTING PARAMETER SETTINGS VIA MIDI (BULK DUMP)

....115/117

CHECKING THE BATTERY AND THE SYSTEM VERSION

.......... 119

CALIBRATING THE FADERS ................................... 119

MIDI DATA FORMAT ............... 120

MIDI IMPLEMENTATION CHART ............................ 134

PARTS LIST

BLOCK DIAGRAM

OVERALL CONNECTOR CIRCUIT DIAGRAM

CIRCUIT DIAGRAM

This document is printed on chlorine free (ECF) paper with soy ink.

DIGITAL MIXING CONSOLE

200304-250000

（目次）

（

総合仕様

）

（寸法図）

（パネルレイアウト）

（ユニットレイアウト）

（分解手順）

（オプションカードの取り付け）

（LSI端子機能表）

（ICブロック図）

（シート基板図）

（検査）

（サービス検査プログラム）

（01V96の初期化）

（内部設定をMIDI経由で出力（バルクダンプ機能））

（バッテリーの残量やシステムのバージョンの確認）

（フェーダーのキャリブレーション）

（MIDIデータフォーマット）

（MIDIインプリメンテーションチャート）

（ブロックダイアグラム）

（総コネクタ接続回路図）

（回路図）

このサービスマニュアルはエコパルプ

（ECF：無塩素系漂白パルプ）を使用しています。

このサービスマニュアルは大豆油

インクで印刷しています。

01V96

IMPORTANT NOTICE

This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed

that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under-

stood by the users, and have therefore not been restated.

WARNING : Failure to follow appropriate service and safety procedures when servicing this product may result in per-

sonal injury, destruction of expensive components and failure of the product to perform as specified. For

these reasons, we advise all Yamaha product owners that all service required should be performed by an

authorized Yamaha Retailer or the appointed service representative.

IMPORTANT : This presentation or sale of this manual to any individual or firm does not constitute authorization certifi-

cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of

any form.

The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and

service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable

and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to

exist, please contact the distributor’s Service Division.

WARNING : Static discharges can destroy expensive components. Discharge any static electricity your body may have

accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to

this bus.)

IMPORTANT : Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power

to the unit.

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where

applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly

other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT

SO EVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose

eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling

food.

WARNING

Components having special characteristics are marked and must be replaced with parts having specification equal to those

originally installed.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be

connected to the terminal in the plug which is marked by the letter E

or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

印の商品は、安全を維持するために重要な部品です。交換する場合は、安全のために必ず指定の部品をご使用下さい。

01V96

Take care not to trap your fingers.

LITHIUM BATTERY HANDLING

This product uses a lithium battery for memory back-up.

WARNING : Lithium batteries are dangerous because they can be exploded by improper handling. Observe the following pre-

cautions when handling or replacing lithium batteries.

Leave lithium battery replacement to qualified service personnel.

Always replace with batteries of the same type.

When installing on the PC board by soldering, solder using the connection terminals provided on the battery cells.

Never solder directly to the cells. Perform the soldering as quickly as possible.

Never reverse the battery polarities when installing.

Do not short the batteries.

Do not attempt to recharge these batteries.

Do not disasemble the batteries.

Never heat batteries or throw them into fire.

ADVARSEL!

Lithiumbatteri-Eksplosionsfare ved fejlagtig handtering. Udskiftning ma kun ske med batteri af samme fabrikat og type. lever det brugte

batteri tilbage til leverandren.

VARNING

Explosionsfara vid felaktigt batteribyte.

Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera anvant batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi rajahtaa, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiiin.

Havita kaytetty paristo valmistajan ohjeiden mukaisesti.

The following information complies with Dutch official Gazette 1995. 45; ESSENTIALS OF ORDER ON THE COLLECTION OF BATTERIES.

• Please refer to the diassembly procedure for the removal of Back-up Battery.

• Leest u voor het verwijderen van de backup batterij deze beschrijving.

リチウム電池の取り扱い

＜注意＞

リチウム電池を誤って交換すると爆発する危険があります。交換する場合は、サービスマニュアルで指定された部品を

使用してください。

（作業中は指を挟まない様に注意して下さい。）

01V96

SPECIFICATIONS

General Spec

Number of scene memories 99

Sampling Frequency Internal 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

External Normal rate: 44.1 kHz–10% to 48 kHz+6%

Double rate: 88.2 kHz–10% to 96 kHz+6%

Signal Delay fs=48 kHz Less than 1.6 ms CH INPUT to STEREO OUT

fs=96 kHz Less than 0.8 ms CH INPUT to STEREO OUT

Fader 100 mm motorized with touch sense ×17

Fader Resolution +10 to –138, – ∞dB input faders

0 to –138, – ∞dB master faders, stereo fader

Total Harmonic Distortion

(CH INPUT to STEREO OUT)

(Input Gain=Min.)

fs=48 kHz Less than 0.05% 20 Hz–20 kHz @ +14 dB into 600 Ω

Less than 0.01% 1 kHz @ +24 dB into 600 Ω

fs=96 kHz Less than 0.05% 20 Hz–40 kHz @ +14 dB into 600 Ω

Less than 0.01% 1 kHz @ +24 dB into 600 Ω

Frequency Response

(CH INPUT to STEREO OUT) fs=48 kHz 20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω

fs=96 kHz 20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω

Dynamic Range

(maximum level to noise level)

110 dB typ. DA Converter (STEREO OUT)

105 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz

105 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz

Hum & Noise

(20 Hz–20 kHz)

Rs=150

Ω

–128 dB Equivalent Input Noise

–86 dB residual output noise. STEREO OUT (STEREO OUT off)

Input Gain=Max.

Input Pad =0 dB –86 dB (90 dB S/N) STEREO OUT

(STEREO fader at nominal level and all CH INPUT faders at minimum level)

Input Pad =0 dB

Input Sensitivity

=–60 dB

–64 dB (68 dB S/N) STEREO OUT

(STEREO fader at nominal level and one CH INPUT fader at nominal level)

Maximum Voltage Gain

74 dB CH INPUT (CH1–12) to STEREO OUT/OMNI (BUS) OUT

40 dB CH INPUT (CH13–16) to STEREO OUT

74 dB CH INPUT (CH1–12) to OMNI (AUX) OUT (via pre input fader)

74 dB CH INPUT (CH1–12) to MONITOR OUT (via STEREO BUS)

Crosstalk

(@ 1 kHz)

Input Gain=Min.

80 dB adjacent input channels (CH1–12)

80 dB adjacent input channels (CH13–16)

80 dB input to output

AD Input (1–12)

Phantom switch +48 V DC (each 4ch)

Pad switch 0/20 dB attenuation

Gain control 44 dB (–60 to –16), detented

Peak indicator LED (red) turns on when post HA level reaches 3 dB below clipping at dig-

ital domain

Signal indicator LED (green) turns on when post HA level reaches 20 dB below nominal at

digital domain

AD converter 24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-

sampling (fs=88.2, 96 kHz)

AD Input (13–16)

Gain control 30 dB (–26 to +4), detented

Peak indicator LED (red) turns on when post HA level reaches 3 dB below clipping at dig-

ital domain

Signal indicator LED (green) turns on when post HA level reaches 20 dB below nominal at

digital domain

AD converter 24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-

sampling (fs=88.2, 96 kHz)

Input selector CH15/16/2TR IN for CH15/16

（総合仕様）

（一般仕様）

01V96

Digital Input

(2TR IN DIGITAL, ADAT input)

Option Input (SLOT) Available cards Optional digital interface cards (MY16, MY8, MY4 series)

Input Channel CH1–32

Input patch —

Phase Normal/reverse

Gate-type*3 On/off

Key in: 12 ch Group (1–12, 13–24, 25–32)/AUX1–8

Comp-type*4 On/off

Key in: self /Stereo Link

Pre EQ/pre fader/post fader

Attenuator –96.0 to +12.0 dB (0.1 dB step)

EQ 4-band PEQ (TYPE1) *5

On/off

Delay 0–43400 samples

On/off —

Fader 100 mm motorized (INPUT/AUX1–8)

Aux send On/off

AUX1–8; pre fader/post fader

Solo On/off

Pre fader/after pan

Pan 127 positions (Left= 1–63, Center, Right= 1–63)

Surround pan 127 ×127 positions

[(Left= 1–63, Center, Right= 1–63)], [(Front= 1–63, Center, Rear= 1–63)]

LFE level –∞, –96 dB to +10 dB (256 step)

Routing STEREO, BUS1–8, DIRECT OUT

Direct out Pre EQ/pre fader/post fader

Metering Displayed on LCD

Peak hold on/off

Stereo Input Channel CH1–4

Input patch (L/R) —

Phase (L/R) Normal/reverse

Attenuator (L/R) –96.0 to +12.0 dB (0.1 dB step)

Equalizer 4band PEQ (TYPE1) *5

On/off —

Fader 100 mm motorized

INPUT/AUX1–8 send

Aux send On/off

AUX1–8; pre fader/post fader

Solo On/off

Pre fader/after pan

Pan (L/R) 127 positions (Left= 1–63, Center, Right= 1–63)

Surround pan

(L/R) 127 ×127 positions

([Left= 1–63, Center, Right= 1–63] x [Front= 1–63, Center, Rear= 1–63])

LFE level (L/R) –∞, –96 dB to +10 dB (256 step)

Routing STEREO, BUS1–8, DIRECT OUT

Metering Displayed on LCD

Peak hold on/off

OSCILLATOR

Level 0 to –96 dB (1 dB step)

On/off —

Waveform Sine 100 Hz, sine 1 kHz, sine 10 kHz, pink noise, burst noise

Routing BUS1–8, AUX1–8, STEREO L/R

STEREO OUT DA converter 24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times over-

sampling (@fs=88.2, 96 kHz)

01V96

MONITOR OUT DA converter 24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times over-

sampling (@fs=88.2, 96 kHz)

OMNI OUT 1–4 Output patch STEREO, BUS1–8, AUX1–8, DIRECT OUT 1–32, INSERT OUT (CH1–32,

BUS1–8, AUX1–8, STEREO), CASCADE OUT (BUS1–8, AUX 1–8, STEREO,

SOLO)

DA converter 24-bit linear, 128-times oversampling (@fs=44.1, 48 kHz), 64-times over-

sampling (@fs=88.2, 96 kHz)

2TR OUT DIGITAL

Dither On/off

Word length 16, 20, 24-bit

Output patch

STEREO, BUS1–8, AUX 1–8, DIRECT OUT 1–32, INSERT OUT (CH 1–32,

BUS 1–8, AUX 1–8, STEREO), CASCADE OUT (BUS 1–8, AUX 1–8, STEREO,

SOLO)

ADAT Output

Dither On/off

Word length 16, 20, 24-bit

Output patch

STEREO, BUS1–8, AUX 1–8, DIRECT OUT 1–32, INSERT OUT (CH 1–32,

BUS 1–8, AUX 1–8, STEREO), CASCADE OUT (BUS 1–8, AUX 1–8, STEREO,

SOLO)

Option Output (SLOT)

Available card Optional digital interface card (MY16, MY8, MY4 series)

Dither On/off

Word length 16/20/24-bit

Output patch

STEREO, BUS1–8, AUX 1–8, DIRECT OUT 1–32, INSERT OUT (CH 1–32,

BUS 1–8, AUX 1–8, STEREO), CASCADE OUT (BUS 1–8, AUX 1–8, STEREO,

SOLO)

STEREO

Comp-type

On/off

Pre EQ/pre fader/post fader

Attenuator –96.0 to +12.0 dB (0.1 dB step)

EQ 4-band PEQ

On/off

On/off —

Fader 100 mm motorized

Balance 127 positions (Left=1–63, Center, Right=1–63)

Delay 0–29100 samples

Metering Displayed on LCD

Peak hold on/off

12-elements x2 LED meters

BUS1–8

Comp-type

On/off

Pre EQ/pre fader/post fader

Attenuator –96.0 to +12.0 dB (0.1 dB step)

EQ 4-band PEQ

On/off

On/off —

Fader 100 mm motorized

Delay 0–29100 samples

Bus to stereo Level (–∞, –130 dB–0 dB)

On/off

Pan: 127 positions (Left=1–63, Center, Right=1–63)

Metering Displayed on LCD

Peak hold on/off

01V96

AUX1–8

Comp-type

On/off

Pre EQ/pre fader/post fader

Attenuator –96.0 to +12.0 dB (0.1 dB step)

EQ 4-band PEQ

On/off

On/off —

Fader 100 mm motorized

Delay 0–29100 samples

Metering Displayed on LCD

Peak hold on/off

INTERNAL EFFECTS

(EFFECT 1–4)

Number of

effects [email protected], 48kHz

[email protected], 96kHz

Bypass On/off

In/out 2-in, 2-out

Effect-in from AUX1–8/INSERT OUT

Effect-out to

Japan

U.S/Canada

Others

Input patch

Power Requirements

100 V, 50/60 Hz 90 W

120 V, 60 Hz 90 W

220-240 V, 50/60 Hz 90 W

Dimensions (H x D x W) 150 x 548 x 436 mm

Net weight 15 kg

Operating free-air temperature range 10–35°C

Storage temperature range –20–60°C

Supplied Accessories

AC Cable (3P/2P AC plug adapter)

CD-ROM (Studio Manager)

Owner’s Manual

Studio Manager Installation Guide

Options Digital interface card (MY16, MY8, MY4 series)

RACK MOUNT KIT: RK1

*1. Total harmonic distortion is measured with a 6 dB/octave filter @ 80 kHz.

*2. Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave

attenuation.

*3. See “Gate Parameters” on page 8.

*4. See “Comp Parameters” on page 8.

*5. See “EQ Parameters” on page 7.

LOW/HPF L-MID H-MID HIGH /LPF

0.1–10.0

(41 points)

low shelving

HPF

0.1–10.0

(41 points)

0.1–10.0

(41 points)

high shelving

LPF

F20 Hz–20 kHz (1/12 oct step)

G±18 dB

(0.1 dB step)

HPF: on/off

±18 dB

(0.1 dB step)

±18 dB

(0.1 dB step)

LPF: on/off

Warranty card (J)

EQ Parameters（EQ パラメーター）

01V96

Gate

Threshold –54 dB–0 dB (0.1 dB step)

Range –70 dB–0 dB (1 dB step)

Attack 0 ms–120 ms (1 ms step)

Hold

0.02 ms–1.96 s (216 points) @ 48 kHz

0.02 ms–2.13 s (216 points) @ 44.1 kHz

0.01 ms–981 ms (216 points) @ 96 kHz

0.01 ms–1.06 s (216 points) @ 88.2 kHz

Decay

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Ducking

Threshold –54 dB–0 dB (0.1 dB step)

Range –70 dB–0 dB (1 dB step)

Attack 0 ms–120 ms (1 ms step)

Hold

0.02 ms–1.96 s (216 points) @ 48 kHz

0.02 ms–2.13 s (216 points) @ 44.1 kHz

0.01 ms–981 ms (216 points) @ 96 kHz

0.01 ms–1.06 s (216 points) @ 88.2 kHz

Decay

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Compressor

Threshold –54 dB–0 dB (0.1 dB step)

Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞(16 points)

Out gain 0 dB to +18 dB (0.1 dB step)

Knee Hard, 1, 2, 3, 4, 5 (6 step)

Attack 0 ms–120 ms (1 ms step)

Release

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Expander

Threshold –54 dB to 0 dB (0.1 dB step)

Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞(16 points)

Out gain 0 dB to +18 dB (0.1 dB step)

Knee Hard, 1, 2, 3, 4, 5 (6 points)

Attack 0 ms–120 ms (1 ms step)

Release

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Gate Parameters

Comp Parameters

（Gateパラメーター）

（Compパラメーター）

01V96

Compander H

Threshold –54 dB to 0 dB (0.1 dB step)

Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points)

Out gain –18 dB to 0 dB (0.1 dB step)

Width 1 dB–90 dB (1 dB step)

Attack 0 ms–120 ms (1 ms step)

Release

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Compander S

Threshold –54 dB to 0 dB (0.1 dB step)

Ratio (x :1) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points)

Out gain –18 dB to 0 dB (0.1 dB step)

Width 1 dB–90 dB (1 dB step)

Attack 0 ms–120 ms (1 ms step)

Release

5 ms–42.3 s (160 points) @ 48 kHz

6 ms–46.0 s (160 points) @ 44.1 kHz

3 ms–21.1 s (160 points) @ 96 kHz

3 ms–23.0 s (160 points) @ 88.2 kHz

Effect library (EFFECT 1–4) Presets 44

User memories 76

Compressor library Presets 36

User memories 92

Gate library Presets 4

User memories 124

EQ library Presets 40

User memories 160

Channel library Presets 2

User memories 127

Input patch library Presets 1

User memories 32

Output patch library Presets 1

User memories 32

Libraries

（ライブラリー）

01V96

In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.

For 2TR IN levels, 0 dBV is referenced to 1.00 Vrms.

All input AD converters (CH INPUT 1–16) are 24-bit linear, 128-times oversampling. (@fs=44.1, 48 kHz)

+48 V DC (phantom power) is supplied to CH INPUT (1–12) XLR type connectors via individual switches.

Three PHANTOM +48V switches CH1–4, 5–8, 9–12 turn on the phantom power for inputs 1–4, 5–8, 9–12 respectively.

In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.

2TR OUT [L, R] levels, 0 dBV is referenced to 1.00 Vrms.

All output DA converters are 24-bit, 128-times oversampling. (@fs=44.1, 48 kHz)

Input PAD GAIN Actual Load

Impedance For Use With

Nominal

Input level Connector

Sensitivity

*1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit

is set to maximum gain. (All faders and level controls are maximum position.)

Nominal Max.

before clip

INPUT A/B

1–12

0–60 dB

3k Ω50–600 Ω

Mics & 600 Ω

Lines

–70 dB

(0.245 mV) –60 dB

(0.775 mV) –40 dB

(7.75 mV) A: XLR-3-31 type

(Balanced)

B: Phone jack

(TRS) (Balanced)

*2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).

*3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).

–16 dB

–26 dB

(38.8 mV) –16 dB

(123 mV) +4 dB

(1.23 V)

20 –6 dB

(338 mV) +4 dB

(1.23 V) +24 dB

(12.28 V)

INPUT 13–16 —–26 dB 10k Ω600 ΩLines

–36 dB

(1.23 mV) –26 dB

(38.8 mV) –6 dB

(388 mV) Phone jack (TRS)

(Balanced)

+4 dB –6 dB

(388 mV) +4 dB

(1.23 V) +24 dB

(12.28 V)

CH INSERT IN

1–12 — 10k Ω600 ΩLines –12 dB

(195 mV) –2 dB

(616 mV) +18 dB

(6.16 V) Phone jack (TRS)

(Unbalanced)

*4. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).

2TR IN [L, R] — 10k Ω600 ΩLines –10 dB

(316 mV) –10 dBV

(316 mV) +10 dBV

(3.16 V) RCA pin jack

(Unbalanced)

Output Actual

Source

Impedance

For Use With

Nominal

Output level Connector

Nominal Max.

before clip

STEREO OUT [L, R] 150 Ω600 ΩLines +4 dB

(1.23 V) +24 dB

(12.28 V) XLR-3-32 type (Balanced)

*1. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).

OMNI OUT 1–4 150 Ω10k ΩLines +4 dB

(1.23 V) +24 dB

(12.28 V) Phone jack (TRS) (Balanced)

*2. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).

MONITOR OUT [L, R] 150 Ω10k ΩLines +4 dB

(1.23 V) +24 dB

(12.28 V) Phone jack (TRS) (Balanced)

CH INSERT OUT 1–12 600 Ω10k ΩLines –2 dB

(616 mV) +18 dB

(6.16 V) Phone jack (TRS) (Unbal-

anced)

*3. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).

2TR OUT [L, R] 600 Ω10k ΩLines –10 dBV

(316 mV) +10 dBV

(3.16 V) RCA Pin Jack (Unbalanced)

PHONES 100 Ω8 ΩPhones 4 mW 25 mW Stereo Phone Jack (TRS)

(Unbalanced)

*4. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND).

40 ΩPhones 12 mW 75 mW

Analog Input Spec

Analog Output Spec

（アナログ入力仕様）

（アナログ出力仕様）

Otros manuales para 01V96

Tabla de contenidos

Otros manuales de Mezclador de música de Yamaha

Yamaha

Yamaha SH-01 Manual de usuario

Yamaha

Yamaha MV12/6 Manual de usuario

Yamaha

Yamaha MG20XU Manual de usuario

Yamaha

Yamaha TF-Rack Manual de usuario

Yamaha

Yamaha DS2416 Manual de usuario

Yamaha

Yamaha CL Series Guía

Yamaha

Yamaha CL5 Instrucciones y recetas

Yamaha

Yamaha PM1D Manager V2 Manual de usuario

Yamaha

Yamaha MJ100 Manual de usuario

Yamaha

Yamaha EM-1620 Manual de usuario

Yamaha

Yamaha AM802 Manual de usuario

Yamaha

Yamaha EMX212S Manual de usuario

Yamaha

Yamaha EMX5 Manual de usuario

Yamaha

Yamaha MV422 Manual de usuario

Yamaha

Yamaha MC1203 Manual de usuario

Yamaha

Yamaha 01x Manual de usuario

Yamaha

Yamaha LS9 Editor Instrucciones y recetas

Yamaha

Yamaha QL5 Manual de usuario

Yamaha

Yamaha PM 5000 Series Manual de usuario

Yamaha

Yamaha MG124C Manual de usuario

Yamaha

Yamaha MC1608M Manual de usuario

Yamaha

Yamaha PM5D Manual de usuario

Yamaha

Yamaha RM800 Manual de usuario

Yamaha

Yamaha MG10 Manual de usuario

Manuales populares de Mezclador de música de otras marcas

Neve

Neve 8816 Manual de usuario

Mackie

Mackie Onyx Analogue Mixer Manual de usuario

Behringer

Behringer EUROPOWER PMP518M Manual de usuario

Peavey

Peavey S-32 Sanctuary Series Manual de usuario

Rane

Rane MP 4 Manual de usuario

True

True T9 Touchscreen Console Manual de usuario

Studiomaster

Studiomaster Air Pro 24 Manual de usuario

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Manual de usuario

Roland

Roland M-160 Manual de usuario

Ecler

Ecler MAC40v Manual de usuario

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Manual de usuario

Veeder-Root

Veeder-Root TLS-350 Series Manual de usuario

Alto

Alto APM80.QUAD Manual de usuario

Omnitronic

Omnitronic PM-211 Manual de usuario

SoundCraft

SoundCraft B400 Manual de usuario

Roland

Roland SoundCanvas SC-8820 Manual de usuario

CARVIN

CARVIN RX 1200 Manual de usuario

Roland

Roland M-16E Manual de usuario