Yaesu FT-991A Manual de usuario

Yaesu FT-991A

1200 Baud Packet Radio Setup

DO NOT connect a USB cable

from your computer to the FT-991

until you load the drivers listed below.

Download the FT-991A/ SCU-17 USB Driver (Virtual COM Port Driver) from the

manufacturer's website and follow the directions to install it on your computer.

This will install 2 new COM ports. One is labeled ENHANCED COM port, and the other

is STANDARD COM port. After you have installed the drivers, you can connect a USB

cable from the PC to the radio.

With the radio still connected you can check that these COM ports were installed on

your computer by going to Device Manager. Click the arrow next to the

“Ports (COM & LTP)” Menu. You should see two newly added ports:

Silicon Labs Dual CP210x USB to UART Bridge: Enhanced COM Port (COM 4*)

Silicon Labs Dual CP210x USB to UART Bridge: Standard COM Port (COM 5*)

(*or a different number) (Make a note of which COM port is which)

Once the ports are installed, The following menu items need to be changed from their

default values in the radio.

•Press the Menu/Setup button.

•Scroll through the menus using the multi-purpose knob.

•Use the touch screen to select a menu Item.

•Turn the multi-purpose knob to adjust the settings.

•Use the touch screen to save the selection.

031 CAT RATE 38400 (This is the baud rate between the radio and modem)

032 CAT TOT 100ms

033 CAT RTS Enable

062 Data Mode OTHERS

064 OTHER DISP (SSB) = 1500 Hz

065 OTHER SHIFT (SSB) = 1500 Hz

066 DATA LCUT FREQ = OFF

068 DATA HCUT FREQ = OFF

070 DATA IN SELECT = REAR

071 DATA PTT SELECT = RTS

072 DATA PORT SELECT = USB

076 FM PKT PTT SELECT = RTS

077 FM PKT PORT SELECT = USB

079 FM PKT MODE = 1200

Next, Download soundmodem113.zip and easyterm49.zip from the UZ7HO

website at http://uz7.ho.ua/packetradio.htm and extract into a new folder.

Open Soundmodem

Click on Settings in the menu bar. Select the Enhanced COM port and Standard COM

port for the Output device and input device, respectively. Check the following boxes

ONLY:

•Single channel output

•Stop waterfall on minimize

•Minimized window on startup

The rest of the settings under “Sound Card”, leave at defaults.

Select PTT Port – Choose the Standard COM Port from above. Then click OK.

Open EasyTerm.

Under the settings menu, select Station Setup.

Enter your Terminal Callsign.

Enter your Mailbox Callsign. Then click OK.

Select your frequency on the FT-991A.

Set the Mode to DATA-FM.

Otros manuales para FT-991A

5

Tabla de contenidos

Otros manuales de Radio de Yaesu

Manuales populares de Radio de otras marcas

EisSound

EisSound KBSound iSelect Manual de usuario

Midland

Midland 1001LWX Manual de usuario

Konig

Konig HAV-SR41 Manual de usuario

Roberts

Roberts exprssion Manual de usuario

VDigi

VDigi DD3.0 Manual de usuario

Radio Shack

Radio Shack 21-1863 Manual de usuario

Roberts

Roberts Stream 207 Manual de usuario

Sony

Sony Walkman SRF-M97 Manual de usuario

Stanley

Stanley FatMax FMC770 Manual de usuario

auna

auna DAB-Radio 10026947 Manual de usuario

SOUNDMASTER

SOUNDMASTER UR190 Manual de usuario

HYT

HYT TC-320 Manual de usuario

auna multimedia

auna multimedia Yellowstone 10026851 Manual de usuario

B-Tech

B-Tech GMRS-V2 Manual de usuario

Weierwei

Weierwei VEV-V8 Manual de usuario

SOUNDMASTER

SOUNDMASTER DAB750 Manual de usuario

Telefunken

Telefunken TF-1505 Manual de usuario

Makita

Makita LXRM03 Manual de usuario