Xylem YSI Pro1030 Manual de usuario

Pro1030

Quick Start Guide

Item #605183

This Quick Start Guide is meant to serve as a quick reference in calibrating and

operating the Pro1030. It is not intended to replace the information found in the User

Manual.

Installing the pH or ORP Sensor

Prior to use, install either a Pro Series pH, pH-ampliﬁed or ORP sensor. Failure to install

a pH or ORP sensor may cause permanent damage to the cable not covered under

warranty.

1. Remove the temporary plastic plug from the cable’s port by pulling it straight

out of the port. This can be discarded.

2. Remove the plastic plug from the sensor’s connector by pulling it straight off the

sensor. This can be discarded.

3. Ensure both the sensor connector and cable connector are clean and dry.

4. Grasp the sensor with one hand and the cable bulkhead in the other.

5. Push the sensor into the connector on the cable until it is ﬁrmly seated and only

1 o-ring is visible. Failure to properly seat the sensor may result in damage.

6. Twist the sensor clockwise to engage the threads and ﬁnger tighten. Do NOT

use a tool. This connection is water-tight.

7. You may remove the shipping storage vessel from the sensing end of the

sensor. This can be saved for later use when storing the sensor for long periods

of time. For short term storage (<30 days), place the probe in the grey storage

sleeve with a sponge moistened with tap water.

pH Calibration

The Pro1030 pH sensor can be calibrated by performing a 1, 2 or 3-point calibration. At

least one of the calibration points must be done with pH buffer 7 or 6.86. For highest

accuracy, perform at least a 2-point calibration.

1 Point Calibration

1. Place the sensor in pH buffer 7 or 6.86 and allow the temperature and pH

readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight pH and press Enter. If pH is not listed as an option, check the System

Setup menu to ensure pH is enabled in the ISE Sensor Type menu.

4. Highlight 1 point and press Enter.

5. If necessary, use the up and down arrow keys to adjust the pH buffer value.

6. Press Enter to complete the calibration or press Cal to cancel.

7. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

8. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen. Refer to the troubleshooting section of the manual for a possible

solution or contact YSI Technical Supportelectrolyte will overﬂow.

2 or 3-Point Calibration

1. Place the sensor in pH buffer 7 or 6.86 and allow the temperature and pH

readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight pH and press Enter. If pH is not listed as an option, check the System

Setup menu to ensure pH is enabled in the ISE Sensor Type menu.

4. Highlight 2 point or 3 point and press enter.

5. If necessary, use the up and down arrow keys to adjust the pH buffer value.

6. Press Enter to continue to second point.

7. Rinse the sensor and place it in the second pH buffer (4/4.01 or 10/9.18). If

necessary, use the up and down arrow keys to adjust the pH buffer value.

8. Wait approximately 30 to 60 seconds for the pH sensor to stabilize and for the

temperature reading to stabilize.

9. Press Enter to either complete the 2-point calibration or to continue with the 3rd

calibration point. Or, press Cal to cancel.

10. If continuing on with a 3rd calibration point, rinse the sensor and place it in the

third pH buffer (4/4.01 or 10/9.18). If necessary, use the up and down arrow keys

to adjust the pH buffer value.

11. Wait approximately 30 to 60 seconds for the pH sensor to stabilize and for the

temperature reading to stabilize.

12. Press Enter to complete the 3-point calibration. Or, press Cal to cancel.

13. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

14. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen.

Conductivity Calibration

The Pro1030 can be calibrated in conductivity, speciﬁc conductance or salinity.

Calibration of any option will automatically calibrate the others. YSI recommends

calibrating speciﬁc conductance for both ease and accuracy. The following procedure

outlines the speciﬁc conductance calibration.

1. Fill a clean container with conductivity calibration solution and place the sensor

into the solution. The solution must cover the holes of the conductivity sensor

that are closest to the cable. Ensure the entire conductivity sensor is submerged

in the solution or the instrument will read approximately half the expected

value. Gently agitate the probe to remove any air bubbles from the conductivity

sensor.

2. Turn the instrument on and allow the conductivity and temperature readings

to stabilize. Press the Cal key. Highlight Conductivity and press Enter. Next,

highlight Sp. Conductance and press Enter.

3. Highlight the units you wish to calibrate, either uS/cm or mS/cm, and press

Enter. 1 mS = 1,000 uS. Next, use the up or down arrow key to enter the value

of the conductivity solution as it is listed for 25°C. Most conductivity solution is

labeled with a value at 25°C. Depressing either the up or down arrow key for 5

seconds will move the changing digit one place to the left.

4. Press Enter to complete the calibration. Or, press Cal to cancel the calibration

and return to the Run screen.

5. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

ORP Calibration

1. Place the clean sensor in ORP calibration solution. Wait for the ORP and

temperature readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight ORP and press Enter. If ORP is not listed as an option, check the

System Setup menu to ensure ORP is enabled in the ISE Sensor Type menu.

4. Use the up and down arrow keys to adjust the ORP calibration solution value.

5. Wait for the temperature reading to stabilize, then press Enter to complete the

calibration or press Cal to cancel.

6. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

7. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen. Refer to the troubleshooting section of the manual for a possible

solution or contact YSI Technical Support.

Visit YSI.com/Pro1030 to ﬁnd the

User Manual, specs, and accessories.

Item# 605057 Dwg# 605183

December 2019 Rev C

1725 Brannum Lane

Yellow Springs, OH 45387

(800) 765-4974, (937) 767-7241

[email protected]

6. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen. Refer to the troubleshooting section of the manual for a possible

solution or contact YSI Technical Support.

Taking Measurements

1. Before taking measurements, be sure the instrument has been calibrated to

ensure the most accurate readings.

2. Turn the instrument on, install the sensor guard and then insert the sensors into

the sample.

3. Ensure the conductivity sensor is completely submerged in the sample. The two

holes near the cable should be covered by the sample for accurate conductivity

readings.

4. Wait for the readings to stabilize.

5. Highlight Save and press Enter to store the reading.

Contact Information

Otros manuales para YSI Pro1030

Tabla de contenidos

Otros manuales de Instrumento de medición de Xylem

Xylem

Xylem WTW Turb 430 IR/T Manual de usuario

Xylem

Xylem Sensus iPERL Manual de usuario

Xylem

Xylem YSI pH/ISE 1320P Manual de usuario

Xylem

Xylem wtw Multi 3310 IDS Manual de usuario

Xylem

Xylem Sensus iPERL Manual de usuario

Xylem

Xylem SI Analytics ViscoClock plus Manual de usuario

Xylem

Xylem WTW Multi 3430 Manual de usuario

Xylem

Xylem SI Analytics HandyLab 600 Manual de usuario

Xylem

Xylem FLYGT MAS 711 Manual de usuario

Xylem

Xylem TM 40 Manual de usuario

Xylem

Xylem WTW pHotoFlex Turb Manual de usuario

Xylem

Xylem ebro FOM 330 Manual de usuario

Xylem

Xylem SI Analytics Lab 865 Manual de usuario

Xylem

Xylem SonTek RiverSurveyor Manual de usuario

Xylem

Xylem Sontek River Surveyor RS5 Manual de usuario

Xylem

Xylem WTW Alyza IQ PO4 Manual de usuario

Xylem

Xylem ebro EBI DA Set Manual de usuario

Xylem

Xylem EXO Series Manual de usuario

Xylem

Xylem WTW inoLab Multi 9310 IDS Manual de usuario

Xylem

Xylem SENSUS PolluTherm Integrator Manual de usuario

Xylem

Xylem FLYGT Concertor APP 411 Manual de usuario

Xylem

Xylem WTW Multi 3320 Manual de usuario

Xylem

Xylem YSI TruLab pH 1110 Manual de usuario

Xylem

Xylem Sensus Domo R Manual de lista de piezas

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario