Xerox WORKCENTER 5222 Manual de usuario

Xerox Multifunction Devices

Customer Tips

PDL Reference Guide for the

WorkCentre 5222/5225/5230

dc08cc0440

October 23, 2008

…for the use

Accessing Extended Features

Overview

This document enables you to access the extended features of the WorkCentre

5222/5225/5230 in environments that do not have a custom print driver.

This document applies

to the stated Xerox

products Note: The commands and syntax used in this document requires familiarity with either

PostScript (PS) or Printer Command Language (PCL).

. It is assumed

that your device is

equipped with the

appropriate option(s)

to support the

information within this

document.

This document provides the Printer Description Language (PDL) commands and syntax

for each feature. The following items are also included:

•A PCL table that describes the PCL features the WorkCentre supports and the syntax

to use the feature.

•A PS table that describes the PS features the WorkCentre supports and the syntax to

use the feature.

This document is not intended to be a complete PS or PCL reference manual. It is a

guide for using the PS and PCL commands with the WorkCentre 5222/5225/5230. Refer

to these sources for additional PS and PCL information:

•PostScript Language Reference Manual, Third Edition, ISBN 0-201-38922-8,

•PCL5 Printer Language Technical Reference Manual

(http://h20000.www2.hp.com/bc/docs/support/SupportManual/bpl13210/bpl13210.pdf),

•Printer Job Language Technical Reference Manual

(http://h20000.www2.hp.com/bc/docs/support/SupportManual/bpl13208/bpl13208.pdf), a

Hewlett-Packard manual.

dc08cc0440

Customer Support Page 1

Using this Guide

Search the Feature Table to determine whether the feature you wish to use is supported.

Verify that the feature is supported by the platform. For example, the WorkCentre must have an optional

finisher installed to use stapling commands.

Follow across the table to find the syntax listed for the PDL examples shown. Reference the

“Dependencies/Caveats” section when working with PS and/or PCL commands.

PCL

This WorkCentre supports PCL5e and PCL XL emulations that enable the features listed in the following

table.

Feature Description

Job Name The value for Job Name is stored for printing on the banner page.

Custom Paper Size Customer designated paper size on which to print a job.

Media Size The size of media on which to print a job.

Media Source Specifies the tray to supply the job’s media.

Output Location Indicates the output bin where the completed print job is sent.

Stapling Indicates use and location of staple(s).

Punch Indicates use, location, and number of holes to be punched.

Booklet This command enables you to print documents as booklets. The pages are

reordered sequentially and are oriented so when folded, the paging is

correct.

Quantity Use this command to specify the number of collated sets of a document.

Resolution Resolution used to image a job.

Bits Per Pixel This command sets the color depth value.

Copies Use this command to specify the number of uncollated sets of a document

in a print job.

Simplex Delivers one-sided output.

Duplex Delivers two-sided output.

Orientation Delivers output in landscape or portrait orientation.

Force Short Edge

Feeding Rotates orientation of job.

Job Mode Specifies the Job Mode.

Job Type Specifies Confidential Print or Proof Print.

Interleaving Paper

(transparency

separator)

Insert blank media to separate sheets of transparent media.

Job Based

Accounting Allows entry of an accounting code and user ID. To enable this feature the

optional Network Accounting kit is required.

Auditron

Delayed Print Specify the time to print a job.

Banner Sheet Turns on/off the banner sheet that prints at the beginning of every job.

dc08cc0440

Customer Support Page 2

PCL/PJL Implementation

The following table contains the PCL feature commands and shows the syntax required to use the feature.

After the table are examples of how to use these commands and examples of a PCL file.

Feature Implementation Values

Job Name @PJL SET JOBNAME =

"jobname-string" Where jobname-string is a maximum of 32

characters

Custom

Paper Size –

available only

for PCL

You have to specify by PCL:

<ESC>&l101A

Width of Custom Paper is specified by

<ESC>&f#I

where # equals decipoints (88.9 mm –

297.0 mm).

Length of Custom Paper is specified by

<ESC>&f#J

where # equals decipoints (98.4 mm –

432.0 mm).

For instance:

4.25-inch x 5.5-inch will give

<ESC>&f3060I3960J by

4.25-inch x 720 decipoints/inch = 3060

and

5.5-inch x 720 decipoints/inch = 3960.

dc08cc0440

Customer Support Page 3

Feature Implementation Values

Media Size @PJL SET PAPER = value Where value is one of the following:

A3: A3 (297 x 420mm)

A4: A4 (210 x 297mm)

A5: A5 (180 x 210mm)

JISB4: B4 (257 x 364mm)

JISB5: B5 (182 x 257mm)

STATEMENT: Statement (5.5 x 8.5”) †

EXECUTIVE: Executive (7.25 x 10.5”)

LETTER: Letter (8.5 x 11”)

JISEXEC: 8.5 x 13”

LEGAL: Legal (8.5 x 14”)

LEDGER: Tabloid (11 x 17”)

COM10: No. 10 Envelope (4.1 x 9.5”)

DL: DL Envelope (110 x 220mm)

MONARCH: Monarch Envelope (3.9 x 7.5”)

C5: C5 Envelope (162 x 229mm)

CUSTOM: Custom paper

†: Whether each paper is available depends

on NV memory setting.

The following paper sizes are only available with

bi-pass tray.

A6: A6 (105 x 148mm)

JISB6: B6 (128 x 182mm)

A4COVER: A4 Cover (223 x 297mm)

POSTCARD: Postcard (4 x 6")

50X70: 5 x 7”

8X10: 8 x 10”

SPANISH: 215 x 315mm

LETTERCOVER: 9 x 11”

11X15: 11 x 15”

JPOST: Postcard (100 x 148mm)

JPOSTD: Postcard (148 x 200mm)

TYOUKEI3: Envelope (120 x 235mm)

dc08cc0440

Customer Support Page 4

Feature Implementation Values

<ESC>&l int A Where int is one of the following:

27: A3 (297 x 420mm)

26: A4 (210 x 297mm)

25: A5 (180 x 210mm)

46: B4 (257 x 364mm)

45: B5 (182 x 257mm)

41: Statement (5.5 x 8.5”) †

1: Executive (7.25 x 10.5”)

2: Letter (8.5 x 11”)

18: 8.5 x 13”

3: Legal (8.5 x 14”)

6: Tabloid (11 x 17”)

81: No. 10 Envelope (4.1 x 9.5”)

90: DL Envelope (110 x 220mm)

80: Monarch Envelope (3.9 x 7.5”)

91: C5 Envelope (162 x 229mm)

101: Custom paper

†: Whether each paper is available depends

on NV memory setting.

The following paper sizes are only available with

bi-pass tray.

24: A6 (105 x 148mm)

44: B6 (128 x 182mm)

200: A4 Cover (223 x 297mm)

216: Postcard (4 x 6")

204: 5 x 7”

208: 8 x 10”

43: 215 x 315mm

201: 9 x 11”

217: 11 x 15”

71: Postcard (100 x 148mm)

72: Postcard (148 x 200mm)

218: Envelope (120 x 235mm)

Media

Source @PJL SET MEDIASOURCE

= value Where value is one of the following:

TRAY1: Feed from paper tray1

TRAY2: Tray2

TRAY3: Tray3

TRAY4: Tray4

SMH: Tray5 (Bypass)

TRAY6: Tray6

dc08cc0440

Customer Support Page 5

Feature Implementation Values

<ESC>&l int H Where int is one of the following:

0: Feed paper from default tray

4: Tray1

1: Tray2

5: Tray3

8: Tray4

7or 20 = Auto

2or 3or 6= Tray5 (Bypass)

21: Tray6

Output

Location @PJL SET OUTBIN = value Where value is one of the following:

UPPER: Center output tray (w/o finisher)

MAINTRAY: Center output tray (w/o

finisher)

CENTERTRAY: Center output tray (w/o

finisher)

MAINTRAY2: Center output tray (w/ B-

Finisher)

LOWER: Side Tray (facing up) (w/ side tray)

SIDETRAY: Side Tray (facing up) (w/ side

tray)

OUTBIN101: Finisher tray (w/ finisher)

<ESC>&l int G Where int is one of the following:

0: Automatic Selection

1: Center output tray (w/o finisher)

2: Side Tray (facing up) (w/ side tray)

4: Center output tray (w finisher)

6: Finisher tray (w/ finisher)

Stapling @PJL SET STAPLE = value Where value is one of the following:

TOPDUAL

TOPLEFT

TOPRIGHT

BOTTOMDUAL

BOTTOMLEFT

BOTTOMRIGHT

LEFTDUAL

RIGHTDUAL

SADDLE

NONE

Punch @PJL SET PUNCH =

value1

@PJL SET JOBATTR =

”@PNHN = value2”

Where value1 is one of the following:

TOP

RIGHT

LEFT

BOTTOM

NONE

Where value2 is one of the following:

TWO: 2 holes

THREE: 3 holes

FOUR: 4 holes

dc08cc0440

Customer Support Page 6

Feature Implementation Values

Booklet @PJL SET JOBATTR =

“@BKLT = value1”

@PJL SET JOBATTR =

“@BKSG = value2”

@PJL SET JOBATTR =

“@BKDN = int1”

Where value1 is one of the following:

NONEDIVIDE: Compile a booklet as long

as the number of sheet does not exceed the

limit

MANUALDIVIDE: Divide sheets based on

the specified limit manually(The number of

sheets is specified with “@BKDN”).

OFF: Do not compile a booklet

Where value2 is one of the following:

RIGHT = Right / Bottom Bind

LEFT = Left / Top Bind

Where int1 is:

1~9999 = Booklet dividing number for each

set

Quantity @PJL SET QTY = int Where int is:

1-999

(If you use this parameter, it also indicate

use collate mode automatically.)

Resolution @PJL SET RESOLUTION =

value Where value is one of the following:

600

Bits Per Pixel @PJL SET BITSPERPIXEL

= value Where value is one of the following:

1: 1 bit per pixel (per plane)

Copies @PJL SET COPIES = int Where int is:

1-999

(This parameter used for uncollated mode.)

<ESC>&l int X Where int is:

1-999

Simplex @PJL SET DUPLEX =

value1 Where value1 is one of the following:

OFF: simplex

<ESC>&l int S Where int is one of the following:

0: simplex

Duplex @PJL SET DUPLEX =

value1

@PJL SET BINDING =

value2

Where value1 is one of the following:

ON: duplex

Where value2 is one of the following:

LONGEDGE

SHORTEDGE

(value2 is used combined with value1=ON)

<ESC>&l int S Where int is one of the following:

1: Duplex Long Edge Binding

2: Duplex Short Edge Binding

Orientation @PJL SET ORIENTATION

= value Where value is one of the following:

PORTRAIT

LANDSCAPE

dc08cc0440

Customer Support Page 7

Feature Implementation Values

<ESC>&l int O Where int is one of the following:

0: Portrait

1: Landscape

2: Reverse Portrait

3: Reverse Landscape

Force short

edge feeding @PJL SET

PAPERDIRECTION = value Where value is one of the following:

SEF: Short Edge Feed

LEF: Long Edge Feed

Job Mode @PJL JOB MODE = value Where value is one of the following:

PRINTER for Printer

Job Type @PJL SET HOLD = value1

See Example 3,4

@PJL SET HOLDKEY

="four-digit string"

Where value1 is one of the following:

PROOF: proof print

STORE: confidential print (secure

print)

The HOLDKEY variable acts as a password

without encryption to protect a held job.

Four-digit string can be any four-digit value

from 0000 to 9999. The default value is "".

When "" (null) is specified, no password is

required.

Interleaving

Paper(Transp

arency

Separator)

@PJL SET SLIPSHEET =

value Where value is one of the following:OFF:

Job Based

Accounting

Auditron

@PJL SET JOBATTR =

"@JOAU = string1"

@PJL SET JOBATTR =

"@JOAP = string2"

@PJL SET JOBATTR =

"@DAID = string3"

Where string1 is a maximum of 32 characters

(ASCII characters in the range 20h - 7Eh are

allowed Only) as job owner (Capital character

& small character is distinguished)

Where string2 is a maximum of 12 characters

(ASCII characters in the range 20h - 7Eh are

allowed Only) as password without encryption.

It can be null (zero length string)

Where string3 is a maximum of 32 characters

(ASCII characters in the range 20h - 7Eh are

allowed Only) as account ID. It can be null

(zero length string)

Note: Auditron and JBA cannot be used at the

same time. So the same command works for

both modes.

Delay Print @PJL SET JOBATTR =

"@PRTM =

YYYY:MM:DD:hh:mm"

YYYY:MM:DD:hh:mm

YYYY: year(AD 2000～2099)

MM: month (1～12)

DD: day (1～31)

hh: hour(0～23)

mm: minute(0～59)

dc08cc0440

Customer Support Page 8

Feature Implementation Values

Banner Sheet @PJL SET JOBATTR=

"@BANR=value"

@PJL SET JOBATTR=

"@BCMT=comment string"

Where value is one of the following:

START: start sheet

DEVICE: depend on device setting

OFF: no banner sheet

Where string is a maximum of 255 characters

(ASCII characters in the range 20h - 7Eh are

allowed Only) as comment for banner.

PJL Template

This section illustrates a standard PJL template that is used to access general print features as

well as WorkCentre Product specific features. This template lists each feature and the syntax,

both PCL commands and PJL, required to use these features. The next section of this document

contains other examples of how to use these commands.

Section 1 (Opening Command, Required for all files)

<ESC>%-12345X@PJL JOB MODE=PRINTER

Section 2 (PJL Set Commands)

@PJL SET RESOLUTION=600

@PJL SET COPIES=1

Section 3 (PCL Code used to invoke PCL Language)

@PJL ENTER LANGUAGE=PCL

Section 4 (PCL Data Stream or ASCII Document inserted here for Options such as

selection Different Fonts, Simplex, Duplex, etc.)

,,,,,,,,,,

Section 5 (Closing Command, Required at end of Document)

<ESC>%-12345X@PJL EOJ

Sample PJL Headers

This section contains examples of these commands in use.

Example 1 Simple Print

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL COMMENT Beginning PCL Job<CR><LF>

@PJL SET OUTBIN=MAINTRAY<CR><LF>

@PJL SET QTY=1<CR><LF>

@PJL SET RESOLUTION=600<CR><LF>

@PJL SET JOBATTR="@JOAU=John"<CR><LF>

Example 2 Finishing Options (Stapling)

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=OUTBIN101<CR><LF>

@PJL SET FINISH=ON<CR><LF>

@PJL SET STAPLE=TOPLEFT<CR><LF>

dc08cc0440

Customer Support Page 9

Example 3 Finishing Options (Punch)

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=OUTPIN101<CR><LF>

@PJL SET FINISH=ON<CR><LF>

@PJL SET PUNCH=LEFT<CR><LF>

@PJL SET JOBATTR="@PNHN=TWO"<CR><LF>

Example 4 Finishing Options (Saddle stapling and folding)

It is an example of division in every 5 sheets.

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>

@PJL SET FINISH=ON<CR><LF>

@PJL SET STAPLE=SADDLE<CR><LF>

@PJL SET JOBATTR="@FOLD=BIFOLDMULTIOUTSIDE"<CR><LF>

@PJL SET JOBATTR="@BKLT=MANUALDIVIDE"<CR><LF>

@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>

@PJL SET JOBATTR="@BKDN=5"<CR><LF>

Example 5 Finishing Options (Bi-Folding(multi page))

It is an example of division in every 5 sheets.

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>

@PJL SET FINISH=NONE<CR><LF>

@PJL SET STAPLE=NONE <CR><LF>

@PJL SET JOBATTR="@FOLD=BIFOLDMULTIOUTSIDE"<CR><LF>

@PJL SET JOBATTR="@BKLT=MANUALDIVIDE"<CR><LF>

@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>

@PJL SET JOBATTR="@BKDN=5"<CR><LF>

@PJL SET QTY=1<CR><LF>

Example 6 Finishing Options (Bi-Folding(single page))

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET OUTBIN=BOOKLETTRAY<CR><LF>

@PJL SET FINISH=NONE<CR><LF>

@PJL SET STAPLE=NONE <CR><LF>

@PJL SET JOBATTR="@FOLD=BIFOLDINSIDE"<CR><LF>

@PJL SET JOBATTR="@BKSG=LEFT"<CR><LF>

Example 7 Proof Print

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL SET HOLD=PROOF <CR><LF>

@PJL SET USERNAME="John" <CR><LF>

@PJL SET JOBNAME="Job1" <CR><LF>

dc08cc0440

Customer Support Page 10

Otros manuales para WORKCENTER 5222

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora de Xerox

Xerox

Xerox 2006NPC - DocuColor Color Laser Manual de usuario

Xerox

Xerox C55/C55mp Manual de usuario

Xerox

Xerox Phaser 7100 Manual de funcionamiento

Xerox

Xerox Phaser 5550 Manual de funcionamiento

Xerox

Xerox PHASER 7500 Manual de usuario

Xerox

Xerox Phaser 750P Manual de usuario

Xerox

Xerox 3117 - Phaser B/W Laser Printer Manual de usuario

Xerox

Xerox Nuvera 100 Manual de usuario

Xerox

Xerox PHASER 6250 Manual de usuario

Xerox

Xerox DocuColor 2240 Manual de usuario

Xerox

Xerox Phaser 6300 Manual de usuario

Xerox

Xerox Docutech 128 Manual

Xerox

Xerox Phaser 8200 Manual de instrucciones

Xerox

Xerox HL-4070CDW Manual de usuario

Xerox

Xerox DocuPrint 900 Manual de usuario

Xerox

Xerox PHASER Phaser 4400 Guía de referencia rápida

Xerox

Xerox Phaser 4 400 Manual de usuario

Xerox

Xerox WorkCentre 4265 Manual de usuario

Xerox

Xerox Phaser 5500 series Manual de usuario

Xerox

Xerox DOCUCOLOR 12 Manual del propietario

Xerox

Xerox Phaser 7100 Manual de funcionamiento

Xerox

Xerox Phaser 6100 Manual de usuario

Xerox

Xerox Phaser 6500 Manual de funcionamiento

Xerox

Xerox 3150 - Phaser B/W Laser Printer Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario