Xerox PHASER 6250 Manual de funcionamiento

Phaser® 6250 Color Laser Printer

1-14

Printer Settings

This topic includes:

■"Accessing the Startup Page" on page 1-14

■"Accessing Power Saver" on page 1-15

■"Accessing Intelligent Ready Mode" on page 1-15

■"Accessing Protected Mode" on page 1-16

■"Accessing Load Paper Timeout" on page 1-17

■"Selecting Tray Settings" on page 1-17

■"Adjusting Front Panel Brightness" on page 1-20

■"Adjusting Front Panel Contrast" on page 1-20

■"Changing Printer Language" on page 1-21

Accessing the Startup Page

The printer automatically produces a “Startup Page” each time the printer is turned on or reset.

You can turn off the automatic printing of the “Startup Page” and later print it from the

information pages menu.

To turn on/off the “Startup Page” use either:

■The printer’s front panel

■CentreWare IS

Using the Printer’s Front Panel

To turn on/off the Startup Page:

1. Select Printer Setup, then press the OK button.

2. Select Printer Controls, then press the OK button.

The Startup Page is highlighted. The end of the line displays the setting (On or Off).

3. Press the OK button to change the setting.

Using CentreWare IS

To turn on/off the automatic printing of the “Startup Page”:

1. Launch your web browser.

2. Enter your printer’s IP address.

3. Select Properties.

4. Click Printer Defaults on the left sidebar of the Properties page.

5. Select Off or On from the Printer Startup Page drop-down list to change the setting.

6. Click Save Changes at the bottom of the page.

Printer Settings

Phaser® 6250 Color Laser Printer

1-15

Printing the Startup Page

To print the “Startup Page”:

1. Select Information, then press the OK button.

2. Select Information Pages, then press the OK button.

3. Select Startup Page, then press the OK button to print.

Accessing Power Saver

To save energy, the printer enters a Power Saver, low-energy consumption mode after a pre-

defined period of time since its last activity. In this mode, most printer electrical systems are

shut down. When a print job is sent to the printer, the printer enters Warmup Mode. You can

also warm up the printer by pressing the OK button on the front panel.

If you find that the printer is going into Power Saver mode too often and you do not want to

wait while the printer warms up, increase the length of time before the printer goes into Power

Saver mode. Change the timeout value as follows:

1. At the printer’s front panel, select Printer Setup, then press the OK button.

2. Select Printer Controls, then press the OK button.

3. Select Power Saver Timeout, then press the OK button.

4. Press the Down Arrow or Up Arrow button to scroll to a selected Power Saver timeout

value. Select a larger value if you want to extend the length of time before the printer goes

into Power Saver mode.

5. Press the OK button.

Accessing Intelligent Ready Mode

Intelligent Ready mode is an automated system that:

■Monitors the printer’s usage.

■Warms up the printer when you are most likely to need it based on past usage patterns.

■Activates the Power Saver mode when the printer times out.

To turn on/off the Intelligent Ready mode, use either:

■The printer’s front panel

■CenterWare IS

Using the Printer’s Front Panel

To turn Intelligent Ready mode on/off:

1. Select Printer Setup, then press the OK button.

2. Select Printer Controls, then press the OK button.

3. Select Intelligent Ready.

4. Press the OK button to turn on/off Intelligent Ready.

5. Select Exit, then press the OK button to return to the main menu.

Printer Settings

Phaser® 6250 Color Laser Printer

1-16

Using CentreWare IS

To select Intelligent Ready mode or to schedule warmup/standby settings:

1. Launch your web browser.

2. Enter your printer’s IP address in the browser’s Address field (http://xxx.xxx.xxx.xxx).

3. Click Properties.

4. Click Warmup on the left sidebar.

5. Click the Warmup Mode drop-down list and select Intelligent Ready, Scheduled, or Job

Activated.

6. If you select Scheduled in Step 5, make selections for each day’s warmup setting and

standby setting.

7. Click Save Changes at the bottom of the screen.

Note

Although the front panel selections only allow you to turn Intelligent Ready Mode on or

off, CentreWare IS allows you to specify particular printer Warmup Modes and settings.

Accessing Protected Mode

Using CentreWare IS

To enter or exit Protected Mode:

1. Launch your web browser.

2. Enter your printer’s IP address in the browser’s Address field (http://xxx.xxx.xxx.xxx).

3. Click Properties.

4. Click the General folder on the left sidebar, then click Printer Defaults.

5. Click the Front Panel Menu drop-down list, then select On or Off.

■Select Off to have all menus available.

■Select On to lock all menu items that change printer setup values.

6. Click Save Changes at the bottom of the page.

Turn on Protected Mode from the front panel to prevent users from changing

printer settings that may impact the jobs of other users. Users can select

printing features, such as color corrections, through the printer drivers. Users

can access general menus that can improve the print quality of their jobs.

These menus direct them to user features, while locking the menus and items

in menus that the system administrator uses to manage the printer.

Printer Settings

Phaser® 6250 Color Laser Printer

1-17

Accessing Load Paper Timeout

When the printer cannot satisfy a print job’s specification for paper tray, type, or size, the front

panel prompts you to load the type and size specified in the print job. If you do not load the

requested paper within the load paper timeout, the printer picks paper from the default tray.

To change the load paper timeout, use either:

■The printer’s front panel

■CenterWare IS

Using the Printer’s Front Panel

To change the load paper timeout:

1. Select Printer Setup, then press the OK button.

2. Select Paper Handling Setup, then press the OK button.

3. Select Load Paper Timeout, then press the OK button.

4. Scroll to the desired timeout value. The values (None, 1,3, 5, or 10 minutes, 1hour or

24 hours) indicate the length of time you want the printer to wait for you to load paper

before printing. If you select a value of None, the printer does not wait for paper to be

inserted and immediately picks paper from the default tray.

5. Press the OK button to save the change.

Using CentreWare IS

To change the load paper timeout:

1. Launch your web browser.

2. Enter your printer’s IP address in the browser’s Address field (http://xxx.xxx.xxx.xxx).

3. Click Properties.

4. Click the General folder on the left sidebar, then click Printer Defaults.

5. Scroll to the desired Load Paper Timeout value in Timeout Settings. The values (None,

1, 3, 5, or 10 minutes, 1or 24 hours) indicate the length of time you want the printer to

wait for you to load paper before printing. If you select a value of None, the printer does

not wait for paper to be inserted and immediately picks paper from the default tray.

6. Click Save Changes at the bottom of the screen.

Selecting Tray Settings

Tray Switching

Tray switching is controlled by the printer driver, front panel, or CentreWare IS. If a specific

tray is selected, tray switching is turned off.

Tray 1 (MPT) and Tray 2, a 500-sheet adjustable tray, are standard with the Phaser 6250

printers. Additional paper feeders can be purchased:

Printer Settings

Phaser® 6250 Color Laser Printer

1-18

■500-Sheet Feeder (Tray 3)

■1000-Sheet High-Capacity Feeder (Tray 3 and Tray 4)

The printer selects the tray from which to draw paper when:

■The front panel paper source is set to Auto Select, and

■The Let printer select which tray to print from option is selected in the printer driver.

Note

If you use the driver to specify a tray to use for your print job, tray switching is disabled

for that job. If the tray becomes empty during printing, the front panel prompts you to load

paper in that tray even if another tray contains the correct paper type and size for the job.

Tray Switching Settings

■If tray switching is enabled, and a tray runs out of paper while printing, then the printer

selects another tray containing the same paper type, size, and orientation to continue

printing the job.

■If tray switching is disabled, and a tray runs out of paper while printing, then the front

panel prompts you that the tray is empty and must be refilled.

Tray Sequence

You can specify the sequence the printer uses to select trays containing the correct paper type

and size for a print job. When a tray runs out of the correct paper during printing, the printer

selects the next tray in the sequence containing the correct paper type and size to continue

printing the job.

For example, if the tray sequence is set to 4-3-2, the printer selects paper from Tray 4 to print a

job. If Tray 4 does not contain the requested paper, or runs out of paper while printing, the

printer selects Tray 3. If neither Tray 4 nor Tray 3 contains the requested paper, or is out of

paper, then Tray 2 is selected.

You can specify the tray sequence by two different methods:

■The printer’s front panel

■CentreWare IS

Printer Settings

Phaser® 6250 Color Laser Printer

1-19

Using the Front Panel

To specify the tray sequence:

1. At the printer’s front panel, select Printer Setup, then press the OK button.

2. Select Paper Handling Setup, then press the OK button.

3. Select Tray Sequence, then press the OK button.

4. Scroll to the desired tray sequence. (If you want to turn off tray switching, select Off.)

5. Press the OK button to save the changes.

Using CentreWare IS

To specify the tray sequence:

1. Launch your web browser.

2. Enter your printer’s IP address in the browser’s Address field (http://xxx.xxx.xxx.xxx).

3. Click the Properties tab.

4. Select Printer Defaults in the left sidebar.

5. Select the desired tray sequence from the Tray Sequence drop-down list. (If you want to

turn off tray switching, select Off.)

6. Click the Save Changes button at the bottom of the screen.

Selecting the Default Tray

If you do not want to use tray switching, you can specify a default tray to use for printing jobs.

The default tray contains the paper type and size used for printing jobs. When the default tray

is empty, or contains a different paper type, you are prompted to load the correct paper type in

the tray even if another tray contains the correct paper type and size for the job.

You can select the default tray by two different methods:

■The printer’s front panel

■CentreWare IS

Using the Front Panel

To select a default tray:

1. Select Printer Setup, then press the OK button.

2. Select Paper Handling Setup, then press the OK button.

3. Select Paper Source, then press the OK button.

4. Scroll to the desired tray to use as the default tray. (If you want tray switching enabled,

select Auto Select.)

5. Press the OK button to save the change.

Using CentreWare IS

To select a default tray:

1. Launch your web browser.

2. Enter your printer’s IP address in the browser’s Address field (http://xxx.xxx.xxx.xxx).

Printer Settings

Phaser® 6250 Color Laser Printer

1-20

3. Click Properties.

4. Select Printer Defaults in the left sidebar.

5. Select the tray from the Paper Source drop-down list.

6. Click Save Changes at the bottom of the screen.

Note

The driver overrides the front panel settings for tray selection.

Adjusting Front Panel Brightness

To adjust the brightness of the front panel’s background lighting:

1. At the printer’s front panel, select Printer Setup, then press the OK button.

2. Select Front Panel Setup, then press the OK button.

3. Select Front Panel Brightness, then press the OK button.

4. Press the Down Arrow or Up Arrow button to increase or decrease the front panel

brightness value. The brightness values range from 0(no background light) to 10

(brightest background light).

5. Press the OK button to save your change.

Adjusting Front Panel Contrast

To adjust the contrast between the text and the background to make the front panel text more

readable:

1. At the printer’s front panel, select Printer Setup, then press the OK button.

2. Select Front Panel Setup, then press the OK button.

3. Select Front Panel Contrast, then press the OK button.

4. Press the Down Arrow or Up Arrow button to increase or decrease the front panel

contrast value. The contrast values range from 1(brightest background light) to 10 (no

background light).

5. Press the OK button to save your change.

Printer Settings

Phaser® 6250 Color Laser Printer

1-21

Changing Printer Language

To change the language used for the text on the front panel, CentreWare IS, and some

information pages:

1. At the printer’s front panel, select Printer Setup, then press the OK button.

2. Select Front Panel Setup, then press the OK button.

3. Select Front Panel Language, then press the OK button.

4. Select the desired language, then press the OK button.

Otros manuales para PHASER 6250

Tabla de contenidos

Otros manuales de Impresora de Xerox

Xerox

Xerox Phaser 4600 Manual

Xerox

Xerox Phaser 3330 Manual de usuario

Xerox

Xerox 6130N - Phaser Color Laser Printer Manual de usuario

Xerox

Xerox Phaser 6120 Manual de usuario

Xerox

Xerox Phaser 7100 Manual de usuario

Xerox

Xerox C11 - DocuPrint Color Inkjet Printer Manual de usuario

Xerox

Xerox Phaser 5550 Manual de usuario

Xerox

Xerox DocuPrint N4025 Manual técnico

Xerox

Xerox DocuPrint C1618 Manual de usuario

Xerox

Xerox 4890 Advanced Manual de usuario

Xerox

Xerox Document Centre 400 series Manual de usuario

Xerox

Xerox VersaLink B600 Manual de usuario

Xerox

Xerox Phaser 4500 Instrucciones de instalación y mantenimiento

Xerox

Xerox D110 Manual de usuario

Xerox

Xerox Phaser 6000 Manual de usuario

Xerox

Xerox PHASER 3435 Manual de usuario

Xerox

Xerox 6100BD - Phaser Color Laser Printer Manual de usuario

Xerox

Xerox 3150 - Phaser B/W Laser Printer Manual de usuario

Xerox

Xerox Nuvera 100 Manual de usuario

Xerox

Xerox Synergix 8825 Guía de inicio rápido

Xerox

Xerox VersaLink C400 Manual de funcionamiento

Xerox

Xerox DocuColor 1632 Manual de usuario

Xerox

Xerox C8 - DocuPrint Color Inkjet Printer Manual de usuario

Xerox

Xerox DocuPrint 65 Manual técnico

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario