Xerox WorkCentre 5222 Manual de usuario

Quick Network Setup Guide

This guide includes instructions for:

Quick Network Setup (DHCP) on page 1

Quick Network Setup (Static IP) on page 3

Note

For more detailed instructions, see the System Administration Guide.

Quick Network Setup (DHCP)

The System Administration Guide contains detailed information about network setups.

Prerequisites for Quick Network Setup Using TCP/IP

1. Confirm that an existing operational network utilizing TCP/IP is available.

2. Confirm that the Ethernet cable is plugged into the multifunction machine and into an

operational Ethernet port on the network.

Note

The Ethernet cable is an RJ45 type and is not supplied by Xerox.

Configuring an IP Address via DHCP

On startup, the multifunction machine defaults to DHCP to obtain its network configurations.

A DHCP server delivers an IP address, as well as other configuration settings to the machine.

If you use a DHCP server to allocate an IP address to the machine, then proceed as follows:

Procedure for Quick Network Setup Using TCP/IP

1. Power on the machine.

2. Wait a minute or so while the machine negotiates an IP address.

3. Print the Configuration Report:

a. Press the <Machine Status> button on the machine.

b. On the [Machine Information] screen, select [Print Reports].

c. Select [Printer Reports].

d. Select [Configuration Report].

e. Press the <Start> button on the machine.

XE3023EN0-2

Quick Network Setup (DHCP)

4. Read the Configuration Report to confirm that an IP address has been allocated and that

it is a valid IP address on your network.

Note

If the IP address starts with 169.xxx.xxx.xxx, then the DHCP server has not

properly allocated an address or DHCP is not enabled on your network.

5. Record the IP address allocated.

6. From a workstation, open a web browser (such as Internet Explorer), and then enter the

machine’s IP address. If connected properly, you should see the CentreWare Internet

Services web page for your machine.

Note

CentreWare Internet Services is a powerful tool for configuring the machine

remotely. The default user name is “11111” and the passcode is “x-admin”. The

user name and passcode are case sensitive and should be changed after install.

7. Load the print drivers on the computers that will be accessing the machine.

Quick Network Setup (Static IP)

Prerequisites for Manual Setup of Network Using Static IP Address

Note

On startup, the WorkCentre multifunction machine defaults to DHCP to obtain its

network configurations, so DHCP must be turned off by manually entering a static IP

address.

Before installing, record the following information for use during setup:

Note

To obtain this information, contact your System Administrator.

Procedure for Manual Setup of Network Using Static IP Address

1. Power on the machine.

2. Press the <Log In/Out> button on the control panel, and then type the System

Administrator login ID to enter the System Administration mode.

Note

The passcode may also be required depending on the machine configuration.

3. Press the <Machine Status> button on the control panel, and then select the [Tools] tab

on the screen.

4. Select [System Settings] in the menu at the left side of the screen.

5. Select [Connectivity & Network Setup] in the [Group] menu.

6. Select [Protocol Settings] in the [Features] menu.

7. Under [TCP/IP - IP Mode], select [IPv4 Mode], [IPv6 Mode], or [Dual Stack].

When IPv4 Mode or Dual Stack is selected in step 7.

a. Select [IP Address Resolution], and then [Change Settings].

b. Select [STATIC], and then select [Save].

c. Select [IPv4 - IP Address], and then [Change Settings].

TCP/IP Address:

Gateway Address:

Subnet Mask (for IPv4) / Prefix (for IPv6):

DNS Server Address:

Quick Network Setup (Static IP)

d. Use the keypad on the screen to enter the IP Address for the machine in the format

"xxx.xxx.xxx.xxx". Select [Save].

e. Select [IPv4 - Subnet Mask], and then [Change Settings].

f. Using the same method as in step d., enter the Subnet Mask.

g. Select [IPv4 - Gateway Address], and then [Change Settings].

h. Using the same method as in step d., enter the Gateway Address.

Note

If you do not wish to set the gateway address, leave this field blank.

i. Select [IPv4 - IP Filter], and then [Change Settings].

j. Select [Enabled] to filter access to the machine.

Note

If you do not wish to use the IP filter feature, select [Disabled].

k. When you have finished establishing TCP/IP, select [Close] on the [Protocol

Settings] screen.

When IPv6 Mode or Dual Stack is selected in step 7.

a. Set [IPv6 Address Manual Configuration] to [Enabled].

b. Select [Manually Configured IPv6 Address], and then [Change Settings].

c. Use the keypad on the screen to enter an IP Address for the machine in the format

"xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx". Select [Save].

d. Select [Manually Configured IPv6 Prefix], and then [Change Settings].

e. Enter an IP address prefix, and then select [Save].

f. Select [Manually Configured IPv6 Gateway], and then [Change Settings].

g. Using the same method as in step c., enter a Gateway Address.

h. Select [IPv6 - IP Filter], and then select [Enabled] or [Disabled].

Note

If you do not wish to use the IP filter feature, select [Disabled].

i. When you have finished establishing TCP/IP, select [Close] on the [Protocol

Settings] screen.

Otros manuales para WorkCentre 5222

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora todo en uno de Xerox

Xerox

Xerox B205 Manual de usuario

Xerox

Xerox Legacy 4112 Guía de instalación

Xerox

Xerox WorkCentre 4118 Manual de usuario

Xerox

Xerox WorkCentre 7232 Manual de usuario

Xerox

Xerox DocuPrint 4850 Manual de servicio

Xerox

Xerox DocuPrint 4850 Guía de referencia

Xerox

Xerox C315 Manual de usuario

Xerox

Xerox WorkCentre XE88 Manual de usuario

Xerox

Xerox WorkCentre BookMark 40 Manual de usuario

Xerox

Xerox 4150 - WorkCentre B/W Laser Guía de instalación y uso

Xerox

Xerox WorkCentre 7132 Manual de usuario

Xerox

Xerox ColorQube 8700 Manual de usuario

Xerox

Xerox WorkCentre 6400V/S Manual de usuario

Xerox

Xerox Phaser 6115 MFP Manual de funcionamiento

Xerox

Xerox WorkCentre Pro 412 Manual de usuario

Xerox

Xerox WorkCentre 7232 Manual de funcionamiento

Xerox

Xerox WorkCentre 6015 Manual de usuario

Xerox

Xerox Wide Format 6030 Manual de usuario

Xerox

Xerox WorkCentre Pro 657 Manual de usuario

Xerox

Xerox WorkCentre 5325 Manual de funcionamiento

Xerox

Xerox Phaser 3200MFP Manual de usuario

Xerox

Xerox Phaser 3250 Manual de usuario

Xerox

Xerox WorkCentre 5845 Manual de usuario

Xerox

Xerox WorkCentre 5665 Manual de usuario

Manuales populares de Impresora todo en uno de otras marcas

Triumph Adler

Triumph Adler DC 2016 Manual

Epson

Epson WorkForce WF-2510 Guía del usuario

Epson

Epson Stylus Scan 2000 Manual de instalación y operación

Epson

Epson PictureMate Snap PM 240 Manual de instrucciones

Konica Minolta

Konica Minolta bizhub C35 Manual de usuario

Brother

Brother MFC-J430w Manual de usuario

Konica Minolta

Konica Minolta BIZHUB 558 Manual de usuario

Lexmark

Lexmark MX710 Series Manual

Brother

Brother MFC-9760 Manual de usuario

Lexmark

Lexmark XC8155 Manual de usuario

Lexmark

Lexmark X642E Manual de usuario

Sharp

Sharp MX-2310U Guía

Aficio

Aficio 200 Manual de usuario

Canon

Canon ImageCLASS 2300 Manual

Ricoh

Ricoh Pro C900 Manual de usuario

Lexmark

Lexmark X925 Manual de usuario

Brother

Brother Business Smart MFC-J4510dw Manual de usuario

Epson

Epson Stylus CX8400 Series Manual de usuario