Xantech HDRXSG01 Manual de usuario
08905063A - 1 -
INSTALLATION INSTRUCTIONS
HDRXSG01
High Definition Receiver Module
DESCRIPTION
The HDRXSG01 CAT5 receiver automatically senses and compensates for the both cable length and
wire quality for the simplest installation in the industry. It senses cable run length in 20-feet
increments and self-adjusts with no switches to set and no charts to consult, removing the guesswork
from high definition video distribution over CAT5 wire.
The HDRXSG01 receiver mounts in the zone up to 1000 feet from the HD44CC5 switcher, and
installs easily in a single-gang J-box. It contains a RJ45 input for the HD video and digital audio signal
as well as a standard IR pass through connection (requires separate wire run) and power connection.
Outputs include component video, digital audio via S/PDIF connection and IR signal.
The HDRXSG01 is to be used with either the HD44CC5 (video matrix transmitter) or HDTXSG01
(single transmitter module). Both the HD44CC5 and HDTXSG01 are sold separately.
SPECIFICATIONS
Size: 1 1/2” W x 2 1/4” D x 4” H
Weight: 0.38 lbs (0.17 kilos)
Bandwidth supports resolutions of 1080p, 1080i, 720p, 480p and 480i.
Includes external power supply (8VAC, 400mA, 50-60Hz)
Gold plated RCA connectors
08905063A - 2 -
QUICK INSTALLATION: HD44CC5 and HDRXSG01
[1] Connect the High-Definition Source to the HD44CC5 or HDTXSG01. The figure below shows a
HD44CC5 (video matrix transmitter).
[2] Using CAT5 cable, connect the HD44CC5 zone output. Be sure to connect power to the
HD44CC5 first. Then connect power to the HDRXSG01.
[3] On the HD44CC5, set the correct source to zone to route the signal to the HDRXSG01 from the
connected High-Definition source. Refer to the HD44CC5 manual on how to use RS232 and IR
RC68+ controls for source to zone routing.
[4] Installation Complete! No adjustments needed!
08905063A - 3 -
QUICK INSTALLATION: HDTXSG01 and HDRXSG01
[1] Connect the High-Definition Source to the HDTXSG01.
[2] Using CAT5 cable, connect the HDTXSG01 output to the HDRXSG01 input.
[3] Connect the High-Definition Display to the HDRXSG01.
[4] Installation Complete! No adjustments needed!
08905063A - 4 -
POWER SUPPLY
The HDRXSG01 is supplied with a 8VAC, 400mA power supply. Do not use any power supply other
than the one included with the HDRXSG01.
The HDRXSG01 can be powered from either the front on the unit (DIN connection) or the rear of the
unit (Screw Terminal connection). DO NOT USE FRONT AND REAR POWER SUPPLY
CONNECTIONS AT THE SAME TIME.
Do not install the HDRXSG01 in conditions where the temperature is greater than 55 Celsius (131
degrees Fahrenheit).
IMPORTANT NOTICE
After connecting the CAT5 cable to the receiver (HDRXSG01), the
power supply to the receiver should be unplugged for a few seconds
and then reconnected. This allows the receiver to go through the full
process of line length and line quality self-calibration.
As an alternate process to this procedure, the power may be cycled
off for a few seconds and reapplied to accomplish the same full self-
calibration process.
If for some reason the system losses power at the receiving end
(HDRXSG01), the transmitting end (HD44CC5 or HDTXSG01), or both
ends, the full self-calibration process will automatically occur.
Xantech Corporation
13100 Telfair Avenue, 2/F
Sylmar, CA 91342
www.xantech.com
Phone: (818) 362-0353, Fax: (818) 362-9506
Installation Instructions, HDRXSG01 © 2007 Xantech Corporation
This document is copyright protected. No part of this manual may be copied or reproduced in any form without prior
written consent from Xantech Corporation.
Xantech Corporation shall not be liable for operational, technical, or editorial errors/omissions made in this document.
Document Number 08905063A
Tabla de contenidos
Otros manuales de Receptor de Xantech
Xantech
Xantech Micro Link 49085D Manual de usuario
Xantech
Xantech 48195D Manual de usuario
Xantech
Xantech Micro Link 490D Series Manual de usuario
Xantech
Xantech 490-95 KITRP Manual de usuario
Xantech
Xantech ML25 Manual de usuario
Xantech
Xantech XT-CAT-ARC-KIT Manual de usuario
Xantech
Xantech 490-85 KITRP Manual de usuario
Xantech
Xantech ML85K Manual de usuario
Xantech
Xantech 291-95 KITRP Manual de usuario
Xantech
Xantech 291-10 Manual de usuario
Xantech
Xantech 490-95 Manual de usuario
Xantech
Xantech 780-10 Manual de usuario
Xantech
Xantech MICRO LINK 490-30 Manual de usuario
Xantech
Xantech ML25K Manual de usuario
Xantech
Xantech ML85 Manual de usuario
Xantech
Xantech 29110D Manual de usuario
Xantech
Xantech XT-DL-IRK Manual de usuario
Xantech
Xantech Wall Link WL25 Manual de usuario
Xantech
Xantech WL85 Manual de usuario
Xantech
Xantech 480-85 Manual de usuario
