X-Vision XPD700WIR-2 Manual de usuario
Before you begin
Model: XPD700WIR-2
• Please unpack the box carefully and idenfy that all the parts are present.
• Please bear in mind the following points when choosing a mounng posion.
> The camera must be posioned so that it will not point directly into the sun (sunrise
and sunset) or any bright light, as this may cause damage to the camera
> Avoid viewing areas where half the area is in bright sunlight and the other half is
dark, such as in the shadow of a building. All types of cameras have diculty in
‘seeing’ with such a large lux level variaon.
• Do not cut the camera cables, this will void the warranty.
• Make sure you use only the recommended power supply. Damage caused to the
camera by incorrect voltage or wiring is not covered by the warranty.
700 TVL Vandal Resistant Dome
with 40m IR, DNR and WDR
User Manual
2
Contents
1. Safety Precautions ........................................................ 3
2. Product Description ...................................................... 4
3. Features ........................................................................ 4
4. Contents ....................................................................... 4
5. Installation .................................................................... 5
6. Camera OSD Control ..................................................... 7
7. OSD Menu Structure ..................................................... 7
8. SETUP Menu Functions ................................................. 9
8.1 Lens .......................................................................... 8
8.2 Shutter/AGC ............................................................. 8
8.3 White Balance .......................................................... 8
8.4 Backlight ................................................................. 10
8.5 Picture Adjust ......................................................... 10
8.6 ATR ......................................................................... 11
8.7 Motion Detection ................................................... 11
8.8 Day/Night ............................................................... 12
8.9 Noise Reduction ..................................................... 12
8.10 Camera ID ............................................................. 13
8.11 Sync ....................................................................... 13
8.12 Language ............................................................... 13
8.13 Camera Reset ........................................................ 13
3
Thank you for purchasing this Xvision camera. Before operating this product, please
read this instruction manual carefully.
zDo not disassemble or modify the camera. Please refer repairs or service to a
qualified service technician.
zTake care when installing the camera. Avoid scratching the front glass window.
zAvoid shock and vibration. Do not install the camera on an unstable surface. It
can be damaged by improper use or storage.
zDo not attempt to point the camera at the sun or other extremely bright objects.
It can cause image smearing whether the camera is powered on or not and can
lead to the damage of the CCD (Charge Coupled Device).
zWhen camera is installed next to equipment, such as wireless communication
device, that emits a strong electromagnetic field, some irregularity such as noise
on the monitor screen may occur.
zOperating temperature: -10° ~ +45°C
zProvide ample slack in the video and power cables once the camera is installed in
its final position.
zRequest the service of a qualified technician if the camera malfunctions or
generates excessive amounts of heat.
1. Safety Precautions
4
3. Features
2. Product Description
• XPD700WIR-2 Camera
• User Manual
• Screws & Wall Plugs
• Allen Key
4. Contents
The XPD700WIR-2 is a professional CCTV dome camera that has excellent colour
balance and a high resolution 700 TVL image, resulting in natural colours and super
sharp images.
The camera is equiped with high power Infrared (IR) LEDs offering 40m nightvision in
complete darkness and split glass technology that elimates any IR bounceback.
It features a powerful ARM based DSP, which processes the image in real time and
improves it by using Digital Noise Reduction and Wide Dynamic Range to produce an
even image, that does not suffer from bright or dark spots. Further enhancing the
picture is a megapixel lens, which is fully adjustable, allowing you to select the perfect
viewing angle for your application. The camera also features an On Screen Display (OSD)
that allows the user to fully customise the advanced features to its environment.
The XPD700WIR-2 is designed for internal or external use and can be wall or ceiling
mounted.
z700 TVL high resolution colour image
zSony 1/3” Ultra High Resolution CCD Sensor with an Xvision X7 DSP.
zIntegrated Long Life Infra Red LEDs turn on automatically in low light conditions
or complete darkness and provide up to 40 metres
z2.8 to 11mm Varifocal Auto Iris Lens for 26 to 92° viewing angle for super sharp
images and easy selection of the optimum viewing angle during installation.
zSmart DNR (Digital Noise Reduction) reduces the noise on the image when
viewing in low lux environments (like at night). This reduces the size of the image
when being recorded by a DVR, resulting in a saving of disk space.
zWDR (Wide Dynamic Range) feature allows the camera to display balanced
pictures even when the scene being watched has bright spots or various light
levels and back light conditions.
zOn Screen Display menu for complete customisation of advanced features.
zDesigned for wall/ceiling mounting and is suitable for internal or external use.
5
5. Installation
1. Select a suitable posion on the wall or ceiling to install the camera. Take the
mounng bracket o the dome camera by unscrewing the xing screw using
the small Allen key supplied.
2. Rotate the upper ring of the camera, it will unscrew from the dome base. Be
careful when handling the camera as the parts are not xed to the upper ring
or the camera ‘ball’.
3. Using the Dome base as a guide, drill a hole in the middle of the base circle on
the wall or ceiling where the camera is to bemounted, to allow the power and
video cable to be fed through (as shown in the diagram).
4. Screw the Dome base to the wall or ceiling using the Wall Plugs and screws
supplied.
5. Feed the Camera’s cable through the hole and adjust the Camera ‘ball’ so the
camera is posioned in the correct direcon and at the correct angle.
6. When the camera is in the correct posion, put the upper and lower ring of the
camera back into posion.
7. Screw the upper ring back onto the base and re-aach the xing screw to
secure the camera in place.
8. The camera’s focus and zoom can them be adjusted using the 2 adjustment
screws on the front of the camera.
STEP 1
Lower
Ring
Zoom
Adjustment
Focus
Adjustment
Upper
Ring
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
Focus
Adjustment
Zoom
Adjustment
6
5. Installation continued
CONNECT THE POWER & VIDEO CABLES
1. Connect the video output to the monitor or other video device through a 75 Ohms
type coaxial cable.
2. Connect the power source, insert the AC plug into the AC socket and the DC plug
into the DC Jack (+12V DC in jack centre).
12V DC Power Cable
Video Cable
6. Camera OSD Control
Various camera settings can be adjusted using the OSD button located on the
camera’s cable.
Press the SET buon to enter the OSD Menu.
SET
UP
LEFT RIGHT
DOWN
Press these controls For this Action
UP, DOWN Select between items in a list
LEFT, RIGHT Select a menu item to change its settings
SET (MENU) Call up the OSD Menu/
Access a Sub Menu
OSD Button Control Actions
7
7. OSD Menu Structure
Please Note:
• The arrow symbol on the OSD menu indicates that there is a sub-menu
available. You can enter the sub-menu by pressing the SET (Menu) buon.
• RETURN: allows the user to return back to the previous menu.
• NEXT: allows the user to move to page 2 of the main menu.
• BACK: allows the user to return to page 1 of the main menu.
• EXIT: allows the user to exit out of the main menu completely.
• SAVE ALL: allows the user to save all the current sengs.
> AUTO > MANUAL
> ATW > PUSH > USER1 WB > USER2 WB >ANTI CR
> MANUAL WB > PUSH LOCK
> OFF > BLC > HLC
LENS
SHUTTER/AGC
WHITE BALANCE
BACKLIGHT
PICTURE ADJUST
ATR
MOTION DETECTION
PRIVACY
DAY/NIGHT
> AUTO > MANUAL
NOISE REDUCTION
CAMERA ID
SYNC
LANGUAGE
CAMERA RESET
> ON > OFF
> ON > OFF
8
8.1. LENS <Option : AUTO / MANUAL>
Select the iris aperture control method between ‘AUTO’ and ‘MANUAL’ by pressing
LEFT or RIGHT buon. When ‘AUTO’ is selected, you can press the seng buon to
enter its submenu.
• ‘TYPE’ lets you select between DC iris and video iris. However, video iris mode
is not supported on this camera. For the item ‘MODE’, you can select ‘AUTO’ to
let the camera automacally adjust the diameter of aperture. You can also set
the camera to open the aperture to the maximum degree, or use the minimum
aperture. The ‘SPEED’ item allows you to set aperture adjustment speed.
8.2. SHUTTER/AGC <Option : AUTO / MANUAL>
Allows you to congure the shuer speed and the AGC.
• Selecng ‘AUTO’, which is recommended when using a DC-iris lens, will allow the
camera to adjust shuer speed automacally based on the lighng condions.
Congure the funcon under dierent lighng condions in the submenu of
‘AUTO’.
• Under ‘HIGH LUMINANCE’, you can choose ‘AUTO IRIS’ mode (default seng)
to use a xed shuer while making the camera adjust iris level according to the
brightness of the scene. Choose ‘SHUT+AUTO IRIS’ mode to have the camera
adjust iris level according to the brightness, and control the exposure with DC
iris.
8. SETUP Menu Functions
AUTO SETUP
MODE
BRIGHTNESS
RETURN
HIGH LUMINANCE
AUTO IRIS
LOW LUMINANCE
MODE
BRIGHTNESS
AGC
x0.75
SETUP MENU
MODE
SPEED
RETURN
TYPE
AUTO
DC
9
8. SETUP Menu Functions continued
8.3. WHITE BALANCE (WHITE BALANCE MENU)
<Option : ATW / PUSH / USER1 WB / USER2 WB / ANTI CR / MANUAL WB / PUSH LOCK>
White Balance (WB) adjusts the colour temperature of the camera image to match
the type of light available, so that colours appear as natural as possible.
• ATW: Adjusts the cameras automacally to the colour temperature range. ‘SPEED’
controls the speed of ATW. Changing the ‘ATW FRAME’ and ‘ENVIRONMENT’
seng will aect the color temperature range. Smaller value for ‘ATW FRAME’
leads to a smaller range of color temperature. The color temperature ranges
from 2500K to 9500K for indoor environment, and 1800K to 10500K for outdoor
environment.
• Selecng ‘USER1/2’ mode will allow you to adjust the blue gain and red gain
individually. ‘MANUAL’ mode will let you adjust the blue gain and red gain
simultaneously. The ‘ANTI CR’ (an color rolling suppression) mode uses a smaller
range of color temperature than ATW mode does.
8.2. SHUTTER/AGC Continued
• If you have previously selected ‘MANUAL’ for the ‘LENS’ item, the mode will be
forced as ‘SHUT’. The ‘BRIGHTNESS’ item let you adjust the aperture to tailor the
brightness to your preference.
• Under ‘LOW LUMINANCE’, you can choose ‘AGC’ mode (default seng) to have
the camera automacally increase the gain when in low light condions to
produce a brighter image. The ‘BRIGHTNESS’ item allows you to tailor brightness
level to your needs.
• The MANUAL shuer opon provides a submenu that contains Mode, Shuer
and AGC seng. ‘SHUTTER’ item lets you specify the shuer me (between 1/50
sec and 1/10000 sec). Adjust ‘AGC’ level according to your lighng condions.
ATW
DELAY CNT
ATW FRAME
RETURN
SPEED
ENVIRONMENT
x0.75
INDOOR
10
8. SETUP Menu Functions continued
8.5. PICTURE ADJUST
Adjust various settings to sharpen the camera image.
• MIRROR: Provides a mirror reecon (horizontal) of the image.
• BRIGHTNESS: Adjust the brightness of the image (0-255)
• CONTRAST: Adjust the contrast of the image (0-255)
• SHARPNESS: Adjust the shaprness of the image (0-255)
• HUE: Adjust the hue of the image (0-255)
• GAIN: Adjust the gain of the image (0-255)
PICT ADJUST
MIRROR
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
GAIN
RETURN
OFF
8.4. BACKLIGHT <Option : OFF / BLC / HLC>
This funcon allows the user to adjust advanced backlight sengs, giving the
following opons:
• OFF: Turns the BLC funcon o
• BLC: The BLC funcon makes objects in front of a bright scene (such as a
window on a bright sunny day) clearer to see by increasing their brightness and
making the background darker.
• HLC: Select this feature to select masking of bright areas in the image, such as
when viewing number plates when car headlights are on.
SETUP MENU
LENS
SHUTTER/AGC
WHITE BAL
BACKLIGHT
MANUAL
AUTO
OFF
OFF
ON
ATR
MOTION DET
NEXT
EXIT SAVE ALL
PICT ADJUST
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de X-Vision
X-Vision
X-Vision VIS249D-2 Manual de usuario
X-Vision
X-Vision VIS338DX-3 Manual de usuario
X-Vision
X-Vision XSD27ZIR Manual de usuario
X-Vision
X-Vision X100 Series Manual de usuario
X-Vision
X-Vision XSD27ZIR-2 Manual de usuario
X-Vision
X-Vision PCC427 Manual de usuario
X-Vision
X-Vision XSD27ZS Manual de usuario
X-Vision
X-Vision PC810 Manual de usuario
X-Vision
X-Vision XSD27ZIR-2 Manual de usuario
X-Vision
X-Vision XSD27ZIR-2 Manual de usuario
X-Vision
X-Vision XSD27ZS Manual de usuario
X-Vision
X-Vision XPD721WIR Manual de usuario
X-Vision
X-Vision XP1080S20 Manual de usuario
X-Vision
X-Vision XC960DA Manual de usuario
X-Vision
X-Vision XPT600 Manual de usuario
X-Vision
X-Vision VIS238D Manual de usuario
X-Vision
X-Vision XC960VA Manual de usuario
X-Vision
X-Vision XC960VV Manual de usuario
X-Vision
X-Vision XSD27ZDN2 Manual de usuario
X-Vision
X-Vision XPD621 Manual de usuario
