Wyrestorm MAT8T820 Manual de usuario
HDMI 8 x 8 Matrixes (Routing Type)
Model No. MAT8T820 (P/N of this Instructions is INS- MAT8T820)
Features
1) Allows up to eight HDMI audio/video devices to be independently switched to eight
HDMI monitors, HDTVs, or projectors.
2) The eight outputs could show the same or different source simultaneously no matter the
source is HDCP or not.
3) Each output includes one HDMI A type connecter and a set of dual RJ-45 connecters as
the second mirrored HDMI output. The two outputs work simultaneously. The UTP
output supports both dual and single cat5e/cat6
4) Reading and saving EDID function from displays.
5) Support high definition resolutions, including 1080p, 1080i, 720p and other standard
video formats.
6) Each port supports both HDMI and DVI inputs.
7) With extra infrared extension receiver.
8) Six switching modes: panel buttons, local IR, IR call back from remote locations, RS232,
RS485 and Ethernet.
9) Eight IR emitters to control the HDMI sources.
10)HDCP compliant.
11)HDMI 1.3 version.
Dear customer:
Thank you for purchasing this product. For optimum performance and safety, please read these
instructions carefully before connecting, operating or adjusting this product. Please keep this
manual for future reference.
NOTICE
Wyrestorm reserves the right to make changes in the hardware, packaging and any
accompanying documentation without prior written notice.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE:
1) DO NOT EXPOSE THIS UNIT TO WATER OR MOISTURE OF ANY KIND.
2) DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET
OR IN ANY OTHER CONFINED SPACE. MAKE SURE THE UNIT IS WELL
VENTILATED.
3) TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS.
4) DO NOT INSTALL NEAR ANY HEAT SOURCE OR OTHER UNITS THAT MAY
PRODUCE HEAT.
5) DO NOT PLACE UNIT NEAR FLAMES.
6) CLEAN THIS UNIT ONLY WITH DRY CLOTH.
7) UNPLUG THIS UNIT DURING LIGHTNING STORMS OR WHEN UNUSED FOR
LONG PERIODS OF TIME.
8) PROTECT THE POWER CORD FROM BEING WALKED ON OR PINCHED
PARTICULARLY AT PLUGS.
9) ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE
MANUFACTURER.
10)REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.
TABLE OF CONTENTS
Introduction
Package Contents
Panel Descriptions
Connect and Operation
Specification
Typical Application
Maintenance
Product Service
Warranty
Contact Information
INTRODUCTION
Wyrestorm’s MAT8T820 is an 8-by-8 DVI/HDMI true matrix. It allows any of the eight source
(Blue-Ray player, HD DVD player, satellite receiver, game system, etc.) to be routed to any of
the eight displays simultaneously, no matter the source is HDCP or not. Users can choose several
different ways to control the matrix: by using infrared extension receiver, RS232, RS485, LAN,
and supplied remote control. IR emitters in the matrix are for controlling the sources; the IR
control signal could be from remote locations via STP/UTP type HDMI connection on the rear
panel.
MAT8T820 has the ability of equalization and amplification to ensure HDMI signal's
transmission through long cable without quality loss. The transmission distance of STP/UTP
outputs reaches up to 30 meters under the video format of 1080P, together with infrared control
signal.
MAT8T820offers solutions for digital entertainment center, HDTV retail and show site, HDTV,
STB, DVD and projector factory, noise, space and security concerns, data center control,
information distribution, conference room presentation, school and corporate training
environments.
PACKAGE CONTENTS
Main Unit. P/N_ MAT8T820.
1) 12VDC Power Supply. P/N_VDC1204
2) Remote.
3) IR extension cable.
4) USB to UART cable.
5) Operating Instructions. P/N_INS MAT8T820.
6) Mounting ears.
*PART NUMBER (Abbreviation as P/N).
PANEL DESCRIPTIONS
Front panel
1) Power switch.
2) Output selection push button (Use it to choose the output channel you want to change).
3) LED indicator of input for output port 1 to 8.
4) Action Confirmation button (Push the ‘Enter’ button to confirm the changing of input
channel to the output).
5) Input selection knob(Rotate it to select the input to the output)
6) IR window.
Rear panel
1) IR extension.
2) RS485 port.
3) LAN port.
4) IR emitter, corresponding to the Input port from 1 to 8
5) RS232 port.
6) Output 1 to 4 with HDMI and CAT5E.
7) Input ports 1 to 4.
8) Power input.
9) Output 5 and 8 with HDMI and CAT5E.
10)Input ports 5 to 8.
11)DIP switch setting.
Note: RS232 port and LAN port are for matrix control. The LAN port is connected to the
computer via cross UTP and connected to the router or switcher via direct UTP.
CONNECT AND OPERATION
1) Connect the HDMI input sources (such as HD-DVD, PS3, STB etc) into MAT8T820
2) Connect the standard HDMI outputs (such as HD-LCD, HD-DLP) into MAT8T820.
3) Connect two CAT-5E cables to both the STP/UTP outputs of MAT8T820and inputs of
STP/UTP receiver (such as EXT131/33/51/53 etc). Please pay attention to the sequence
of the two cables, CAT5e-1->CAT5e1, CAT5e-2->CAT5e2. (The cable termination must
follow the standard of EIA/TIA 568B, if Single UTP mode, just connect CAT5E-2)
4) Connect the HDMI output (such as: HD-LCD.HD-DLP) into the STP/UTP receiver.
5) Connect the IR RX receiving cable into STP/UTP receiver IR RX and connect The IR
TX cable into MAT8T820 IR emitter.
6) Power on the input source you want to show. (Keep the unused input power off,
otherwise it may interfere the normal display.)
7) Connect the power supply into MAT8T820
8) Turn on the power, when the LED panel stops flashing circularly, the initialization of the
matrix is ready.
9) Turn on the displays you want to watch.
10)Use the remote supplied or push the button on the front panel to choose input source, or
using infrared extension receiver, RS232, RS485 or LAN port to do the control.
Operation on front panel
1) Press the output select button to the output channel which you want to change. Then the
corresponding LED of the output channel will blink slowly.
2) Rotate the input select knob to choose the desired input channel.
3) Press the ‘Enter’ button to confirm the action. Then the LED stops blinking.
Control via RS232.
The Interface of MAT8T820_COMCTL
The Message Window
Receive Window
The “receive window” will show the message received from MAT8T820. When you click the
Control Buttons (see step 4) or send Control Command (see 2.3) to MAT8T820, it will send out
the message about “operation results” as seen below:
Status Button
Click this button to read the status of MAT8T820. The status displays which input is selected by
which output.
Send Window
Input the control command in this window. The control command uses ASCII.
Mode button
Click this button to set the switch mode: Quick switch or Normal switch. When you click this
button it will read the current mode of MAT8T820, if you want to change the mode, select the
mode you want and click OK.
Set IP button
Click this button to set IP address for NETCTL.
The Com Status
Connect state
1) Connect state shows if the com is open or not. If it is open, the state is green. Otherwise,
the state is red.
Tabla de contenidos
Otros manuales de Conmutador de matriz de Wyrestorm
Wyrestorm
Wyrestorm MX-0606-PP Manual de usuario
Wyrestorm
Wyrestorm MX0404-PP Manual de usuario
Wyrestorm
Wyrestorm MX-0404-PP-KIT Manual de usuario
Wyrestorm
Wyrestorm MX-0404-H2A Manual de usuario
Wyrestorm
Wyrestorm MX-0404-H2 v2 Manual de usuario
Wyrestorm
Wyrestorm MX-1010-HDBT-H2X Manual de usuario
Wyrestorm
Wyrestorm MX-0808-H2A-MK2 Manual de usuario
Wyrestorm
Wyrestorm MXV-0808-H2A Manual de usuario
Wyrestorm
Wyrestorm MX-0816-HDBT Manual de usuario
Wyrestorm
Wyrestorm MX-0404-POH-KIT Manual de usuario
Wyrestorm
Wyrestorm MXV-0606-H2A Manual de usuario
Wyrestorm
Wyrestorm MX-0808-PP-AUD Manual de usuario
Wyrestorm
Wyrestorm ESSENTIALS EXP-MX-0402-H2 Manual de usuario
Wyrestorm
Wyrestorm ESSENTIALS EXP-MX-0404-KIT Manual de usuario
Wyrestorm
Wyrestorm MAT4T401 Manual de usuario
Wyrestorm
Wyrestorm MXV-0808-H2A-70 Manual de usuario
Wyrestorm
Wyrestorm MX-0404-HDBT-H2-KIT Manual de usuario
Wyrestorm
Wyrestorm MX-0404-HDMI Manual de usuario
Wyrestorm
Wyrestorm MXV-0408-H2A Manual de usuario
Wyrestorm
Wyrestorm MX-1010-H2XC Manual de usuario
