Woxcon TPHD463 Manual de usuario
TPHD463
HDBaseT Lite Transmitter/PoH
All Rights Reserved
Version: 2016V1.0
User Manual
HDBaseT Lite Transmitter/PoH
Preface
Read this user manual carefully before using this product. Pictures shown in this
manual is for reference only, different model and specifications are subject to real
product.
This manual is only for operation instruction only, not for any maintenance usage. Any
changes of functions and parameters since then will be informed separately. Please
refer to the dealers for the latest details.
Trademarks
Any other trademarks mentioned in this manual are acknowledged as the properties of
the trademark owner. No part of this publication may be copied or reproduced without
the prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.
HDBaseT Lite Transmitter/PoH
SAFETY PRECAUTIONS
To i nsur e the b es t f r om t he p rod u ct, plea s e r e ad a ll ins t ruct i ons c a refu l ly b e for e usi n g
the device. Save this manual for further reference.
l Unpack the equipment carefully and save the original box and packing material for
possible future shipment
l Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
l Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
l Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
l Refer all servicing to qualified service personnel.
l To p r event fire or s h oc k ha z ard , do not e xpos e the unit to r ain, mois t ure or ins t all
this product near water.
l Do not put any heavy items on the extension cable in case of extrusion.
l Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
l Install the device in a place with fine ventilation to avoid damage caused by
overheat.
l Keep the module away from liquids.
l Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module immediately.
l Do not twist or pull by force ends of the optical cable. It can cause malfunction.
l Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
l Unplug the power cord when left unused for a long period of time.
l Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.
HDBaseT Lite Transmitter/PoH
Contents
1. Introduction .................................................................................................................. 1
1.1 Product Overview ............................................................................................... 1
1.2 Package Contents .............................................................................................. 2
2. Panel Description ........................................................................................................ 3
3. Installation Instructions ................................................................................................ 4
3.1 Basic Installation ................................................................................................ 4
3.2 Device Power ..................................................................................................... 5
3.3 RS232 Connections ........................................................................................... 5
4. General Operation ....................................................................................................... 7
4.1 Automatic Switching ........................................................................................... 7
4.2 RS232 Switching ................................................................................................ 7
4.3 LED indicators .................................................................................................... 7
4.4 Firmware Port ..................................................................................................... 8
4.5 EDID Management ............................................................................................. 8
4.6 HDCP Management ........................................................................................... 9
4.7 Low Power Mode ................................................................................................ 9
4.8 Display Control Functionality ............................................................................ 10
5. RS232 Control ........................................................................................................... 11
5.1.1 Installation/uninstallation of RS232 Control Software ............................ 11
5.1.2 Basic Settings ......................................................................................... 11
5.1.3 Switching Commands ............................................................................. 12
5.1.4 Power Management ............................................................................... 14
5.1.5 HDCP Compliance ................................................................................. 14
5.1.6 Device Baud Rate .................................................................................. 14
5.1.7 Device Information ................................................................................. 14
5.1.8 Factory Reset ......................................................................................... 15
5.1.9 EDID Configuration ................................................................................ 15
5.1.10 VGA Scaling Configuration ................................................................... 15
5.1.11 Display Control Settings ....................................................................... 16
HDBaseT Lite Transmitter/PoH
5.1.12 Display Control Queries ....................................................................... 18
5.1.13 Display Control Hex Commands .......................................................... 19
6. Troubleshooting ......................................................................................................... 20
7. Techn i cal S peci fic a tion s ............................................................................................. 21
8. After-sales Service ..................................................................................................... 23
HDBaseT Lite Transmitter/PoH
1
1. Introduction
1.1 Product Overview
The product is an under table mounted switcher designed to be the primary PC
interface for classrooms, boardrooms, and conference centers. It features VGA + Audio
to HDMI conversion with VGA scaling up to 1920x1200 and an HDMI input.
The HDBaseT Lite Transmitter utilizes HDBaseT technology to extend the digital output
up to 70 meters away using solid core shielded Category 5e or greater cable. This
transmitter device is compatible with several HDBaseT receivers, but is designed to
work primarily with the HDBaseT Receiver. The unit features multiple EDID modes to
eliminate user confusion, and incompatible video formats. An HDMI output is available
for use to connect to a local display.
The HDBaseT Lite Transmitter can be powered from the rear panel or by Power over
HDBaseT (PoH), including midspan injectors that support Power over Ethernet (PoE)
Alternative A. The HDBaseT Lite Transmitter may also power compatible HDBaseT
receivers. Built-in surge protection and diagnostic LEDs ensure hassle-free and robust
installations. The HDBaseT Lite Transmitter also features a customizable power
management system, which will put the unit into a low power state after no video for 30
minutes or being inactive for 3 hours by default.
The HDBaseT Lite Transmitter will detect which input has an active video input, and
switch to that input – if both inputs are active, the “last in” will be selected. RS232
control of the HDBaseT Lite Transmitter can be accomplished by connecting to the
RS232 port on a compatible receiver, such as a HDBaseT Receiver, or through a direct
connection on the RS232 input of the device.
The HDBaseT Lite Transmitter can be programmed to control the connected display.
This allows display power and input to be automatically controlled based on video
activity, eliminating the need for a third party control system in many installations.
HDBaseT Lite Transmitter/PoH
2
1.2 Package Contents
l HDBaseT Lite Transmitter
l 12V DC Power Supply
l RS232 cable (3-pin to DE9)
l 3-pin Removable Screw Terminal
l USB Programming Cable
l User Manual
NotePlease confirm if the product and the accessories are all included, if not, please
contact with the dealers.
HDBaseT Lite Transmitter/PoH
3
2. Panel Description
1. Micro USB port for firmware updating.
2. HDCP status LED.
3. HDBaseT Link status LED.
4. VGA input status LED.
5. HDMI input status LED.
6. Power LED.
A. HDBaseT output with PoH
support.
B. Local HDMI output.
C. HDMI input.
D. VGA with analog audio input.
E. RS232 connection
F. 12V DC power input
Note: Pictures shown in this manual are for reference only, different model and
specifications are subject to real product.
HDCP LINK HDMIFIRMWARE VGA
HDMI OUT HDMI IN DC 12V
Tx Rx
PoH
HDBT VGA IN
1
ABCDEF
2345 6
HDBaseT Lite Transmitter/PoH
4
3. Installation Instructions
3.1 Basic Installation
1. Turn off power and disconnect the audio/video equipment by following the
manufacturer’s instructions.
2. Connect shielded Category 5E or greater twisted pair cable with the TIA/EIA-568B
crimp pattern between the transmitter (HDBaseT Lite Transmitter) and the
HDBaseT receiver.
3. If the HDBaseT receiver cannot provide power to the HDBaseT Lite Transmitter or
the receiver requires remote power, connect the included power supply to the 12V
DC power input of the device.
4. Connect an HDMI cable between the display and the HDBaseT receiver per the
manufacturer’s instructions
5. If a local display is part of the installation, connect an HDMI cable between the
display and the HDMI output port on the HDBaseT Lite Transmitter.
6. Power on attached audio/video devices.
7. Apply power to the HDBaseT receiver.
8. If the HDBaseT receiver cannot provide power to the HDBaseT Lite Transmitter or
the receiver requires remote power, connect the power supply going to the
HDBaseT Lite Transmitter an AC outlet.
9. Connect HDMI or VGA/Audio sources. The analog audio input is only paired with
the VGA input.
HDBaseT Lite Transmitter/PoH
5
HDBaseT Cabling Requirements
For all HDBaseT Cabling, the EIA/TIA-568B crimp pattern must be used on
Category 6 or greater cable. In areas with large amounts of electromagnetic (EM) or
radio frequency (RF) interference, a shielded variety of Category 5e or greater cable
is recommended with shielded connectors on both ends of the selected cable.
3.2 Device Power
The HDBaseT Lite Transmitter supports two types of power input: PoH (Power over
HDBaseT) and rear panel input.
When using PoH, a compatible HDBaseT receiver can power the HDBaseT Lite
Transmitter by inserting power onto the twisted pair cable. When using a compatible
HDBaseT receiver, there is no need to use the rear panel power input.
If using a different receiver that does not supply power or the receiver requires remote
power, you must connect power to the rear power input. Using this method, the
included 12V DC 2A power supply must be used.
3.3 RS232 Connections
The HDBaseT Lite Transmitter can be controlled via RS232 by connecting to a
computer’s serial port or third party control system via the connected HDBaseT
receiver. The HDBaseT Lite Transmitter may also be directly controlled via the RS232
connection on the rear panel. Additionally, a third party device connected to the local
RS232 port may communicate directly to the display via RS232 through the HDBaseT
receiver.
Tabla de contenidos
Otros manuales de Transmisor de Woxcon
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
