Worx MakerX WX746 Manual de usuario
WX746
WX746.X
20V Cordless Glue Gun
1
2
3
4
5
6
A B
C
E
D
F
Red on
Green on
EN
PRODUCT SAFETY
WARNING: Read all safety warnings and instructions.
Failure to follow
all instructions listed below may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
-Children should be supervised to ensure that they do not play with the appliance.
WARNING: For the purposes of recharging the battery, only use the detachable
supply unit provided with this appliance.
ADDITIONAL SAFETY INSTRUCTIONS FOR GLUE GUNS
A fire may result if the appliance is not used with care, therefore
– be careful when using the appliance in places where there are combustible
materials;
– do not apply to the same place for a long time;
– do not use in presence of an explosive atmosphere;
– be aware that heat may be conducted to combustible materials that are out of
sight;
– place the appliance on its stand after use and allow it to cool down before
storage;
– do not leave the appliance unattended when it is switched on.
SAFETY WARNINGS FOR BATTERY PACK
a) Do not dismantle, open or shred cells or battery pack.
b) Do not short-circuit a battery pack. Do not store battery packs
haphazardly in a box or drawer where they may short-circuit each other or
be short-circuited by conductive materials. When battery pack is not in use,
keep it away from other metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
c) Do not expose battery pack to heat or fire. Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the liquid to come into contact
with the skin or eyes. If contact has been made, wash the affected area
with copious amounts of water and seek medical advice.
f) Keep battery pack clean and dry.
g) Wipe the battery pack terminals with a clean dry cloth if they become
dirty.
EN
h) Battery pack needs to be charged before use. Always refer to this
instruction and use the correct charging procedure.
i) Do not maintain battery pack on charge when not in use.
j) After extended periods of storage, it may be necessary to charge
and discharge the battery pack several times to obtain maximum
performance.
k) Recharge only with the charger specified by Worx. Do not use any charger
other than that specifically provided for use with the equipment.
l) Do not use any battery pack which is not designed for use with the
equipment.
m) Keep battery pack out of the reach of children.
n) Retain the original product literature for future reference.
o) Remove the battery from the equipment when not in use.
p) Dispose of properly.
q) Do not mix cells of different manufacture, capacity, size or type within a
device.
r) Keep the battery away from microwaves and high pressure.
SYMBOLS
Read operator’s manual
Warning
Wear eye protection
Wear protective gloves
Do not burn
Batteries may enter water cycle if disposed improperly, which
can be hazardous for ecosystem. Do not dispose of waste
batteries as unsorted municipal waste.
EN
Li-Ion battery. This product has been marked with a symbol
relating to ‘separate collection’ for all battery packs and
battery pack. It will then be recycled or dismantled in order to
reduce the impact on the environment. Battery packs can be
hazardous for the environment and for human health since
they contain hazardous substances.
COMPONENT LIST
1. NOZZLE
2. CAP
3. TRIGGER
4. GLUE STICK HOLE
5. POWER BUTTON
6. GLUE STICK*
* Not all the accessories illustrated or described are included in stan-
dard delivery.
TECHNICAL DATA
WX746 WX746.X **
Rated voltage 20 V Max. ***
Glue Stick Diameter 7.2mm
Nozzle Caliber 1.2 mm
Preheating Time 25 s
Temperature when heated 200° C
Runtime(2.0Ah) more than 120 mins
Machine weight (bare tool) 0.12Kg
* * X=1-999, A-Z, M1-M9 there are only used for different customers, there are no safe
relevant changes between these models.
** * Voltage measured without workload. Initial battery voltage reaches maximum of 20
volts. Nominal voltage is 18 volts.
EN
Category Model Capacity
20V Hub/HubX
WA7160 Input: 20 V 10 A Max.
Output: 20 V 10 A Max.
WA7161 Input: 20 V 10 A Max.
Output 1: 20 V 10 A Max.
Output 2: 5 V 2 A (USB port)
We recommend that you purchase your accessories from the same store that sold you
the tool. Refer to the accessory packaging for further details. Store personnel can assist
you and offer advice.
MakerX series tools and 20V Hub/HubX are specially designed to work together, so do
not attempt to use any other devices.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction book carefully.
INTENDED USE
The tool can be used for bonding wood, leather, plastics ,papers and other mate-
rials.
ASSEMBLY
1. Insert the appropriate glue stick for the material being glued via the hole at
the rear of the glue gun.Use 7.2mm mini glue sticks (See Fig. A)
2. Connect the gun and the hub. (See Fig. B)
WARNING: Before operation, make sure the speed control button on
the hub is at the “Min” position. (See Fig. C) and the surfaces to be
glued must be clean, dry and free of grease.
NOTE The speed control does not work with the glue gun. The speed
control is for other tools, such as the MakerX Rotary Tool or Angle
Grinder.
OPERATION
1. Confirm the speed control button is set to “Min”. Grasp the tool by the grip.
Press the on/off switch on the hub. Then press button on the tool for 3s until
the it turns red ,which means the glue gun is heating. When the light turns
green, the gun is ready for operation. Press the trigger for gluing. (See Fig.
D,E,F) After applying the glue, immediately press the surfaces to be glued
together.
NOTEIt is recommended to apply the glue on large surfaces or long work
pieces in the form of points. On flexible materials, apply in lines.
EN
WARNING: Do not allow the hot glue or the nozzle tip to come into
contact with persons or animals.If hot glue contacts with the skin,
do not try to remove the glue from the skin,but put the affected area
immediately under a stream of cold water for several minutes.
2. Press the power button until the light goes out. Then press the on/off switch
on the hub to turn off after use.
NOTE In order to save energy, the glue gun switches off automatically after 10
minutes.
NOTE Put down the glue gun in a safe way and allow it to cool down completely
before packing it away after each use.
MAINTENANCE
Remove the battery before carrying out any adjustment, servicing or
maintenance.
There are no user serviceable parts in your power tool. Never use water or
chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor ventilation slots clean. Keep
all working controls free of dust. Occasionally you may see sparks through the
ventilation slots. This is normal and will not damage your power tool.
Store the accessories in a dry place.
WARNING Do not use inflammable solvents for cleaning the surfaces
to be glued. For excess hardened glue, it can be removed with a blunt
object. Do not use solvent for cleaning.
TROUBLESHOOTING
Problems Possible Causes Possible Solution
No glue comes out Glue stick is used up.
Glue stick diameter is too
large or small.
Glue stick is not pushed to
the end.
Insert a new glue stick.
Use recommended glue
sticks.
Push the glue stick to the
end when loading.
Glue stick falls out
from the tool. Glue stick diameter is too
small. Use recommended glue
sticks.
There is glue leaking
out without trigger
pressed after use.
The temperature is still
high in short time after use
and will cause glue melted.
It is normal and will stop
leaking out when the
glue gun cools down.
EN
Trigger is blocked for
glue escaping toward
the rear.
Glue stick diameter too
small.
Glue stick’s melting
temperature is too low.
Use recommended glue
sticks.
Glue does not flow
evenly. Glue stick’s melting
temperature is too low.
Glue is not heated long
enough.
Trigger is not pressed
uniformly.
Wait for heating.
Allow the glue gun time
to heat up.
Press trigger slowly and
uniformly.
Adhesive surface only
bonds on one side. Adhesive already partially
has cooled off before
work-pieces have been
bonded.
Bond work-pieces in a
quicker way.
Set gluing points instead
of applying glue over
surface.
Adhesive bond doesn’t
work after cooling. Surface is greasy or too
smooth.
Surface is dusty.
Unsuitable material or
work-piece.
Roughen adhesive
surface slightly.
Clean the surface.
Use specialized
adhesive.
Glued tiles in moist
locations are not
adhesive.
Moisture spreads under
bonding parts. Suggest to use
specialized adhensive
suitable for moist
locations
Glued shoe soles are
not adhesive. Moisture causes leather to
puff up and creeps under
bonding location.
Use specialized
adhesive.
Strands are pulled
out when removing
the glue gun from the
work-piece.
Trigger is still pressed after
operation.
Nozzle has not been wiped
off.
Discontinue pressing
trigger before
completing the
operation.
Wipe off nozzle.
Work-piece melts. Work-piece contains
material that melts at a low
temperature.
Use specialized
adhesive.
Otros manuales para MakerX WX746
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Pistola de pegamento de Worx
