Woo Audio WA22 Manual de usuario



WOO AUDIO WA22

Fully Balanced Class-A Stereo Headphone Amplifier

Owner’s Manual

Please review this manual before operating your WOO AUDIO™ product.



Important Safety Information

CAUTION: These amplifiers are shipped without the vacuum

tubes installed. It is necessary to install the tubes first. The tubes

must be installed correctly or serious damage that is not covered

by the warranty will result.

Turn off immediately in the event of malfunction

Should you notice smoke or an unusual smell coming from the

equipments, turn it off immediately. Continued operation could

result in injury.

Do not disassemble

High voltage circuit. Touching the product’s internal parts could

result in injury. In the event of malfunction, the product should be

repaired only by a qualified technician.

Keep out of children

Failure to observe this precaution could result in injury.

WARNING: Failure to follow these instructions could result in

fire, electric shock, or other injury or damage.



Table of Contents

IMPORTANT SAFETY INFORMATION 2

TABLE OF CONTENTS 3

OVERVIEW 4

QUICK INSTALLATION 5

OPERATION 9

COMPATIBLE TUBES 11

FAQ - FREQUENTLY ASKED QUESTIONS 12

WARRANTY AND SERVICE 13

REVIEWS 14

PRODUCT SPECIFICATION 15



Overview

Thank you for choosing a Woo Audio product. The WA22 is a finely hand-crafted

amplifier that delivers uncompromised performance and superior listening experience.

Point-to-Point wiring

True balanced topology

All tubes. No semi-conductors in the entire signal circuitry

Soft start tube protection circuit

One 5U4G rectifier tube

Two 6SN7 drive tubes, one per channel

Two 6AS7 / 6080 power tubes, one per channel

DACT CT2 balanced stereo stepped attenuator

One balanced XLR input

One single-ended RCA input

One mono 3-pin headphone output (left and right channel)

One 4-pin stereo headphone output

One TRS headphone output (1/4”)

High and low impedance headphone output

Die cast full aluminum enclosure and knobs, anodized finished



Quick Installation

What’s in the box?

①WA22 amplifier

②One matched pair of 6080 power tubes

③One 5U4G rectifier tube

④One matched pair of 6SN7 driver tubes

The actual tubes may look different.

Compatible tubes may be included instead of the ones illustrated above.

Power cord and interconnection cable are not included.



Installing the tubes:

Note: avoid oil or smudge on the tube glass; clean hands before installation.

1. Find the correct tube for the socket. There is a label below each tube socket that

indicates a standard tube for the amplifier. For example, a 6080 tube should

install on the “6080” labeling socket. You MUST use the compatible tube or

serious damage may occur to the amplifier. See Compatible Tubes section for all

the approved direct substitute tubes.

2. Align the tube guide pin to the socket as below.

3. Hold the tube base firmly then squeeze it into the socket slowly. Be sure to apply

force perpendicular to the tube socket; never insert the tube at an angle. Apply

slight rocking motion for the tube, which is harder to insert; never apply circular

motion. Apply pressure from the top of the tube if needed.

Tube to tube

Tube socket guide pin indicator

Guide pin shows on the

bottom of a tube.

Do no insert a tube at an angle

Insert a tube perpendicular to

the socket.

Hold base firmly.







4. Check installation. The tube pins should be inserted fully into the tube socket

receptacles.

Selecting AC voltage:

WARNING: failure to select the correct voltage will result in damage of the amp.

Installing the power cord:

Plug the power cord into the AC inlet. See ①in the below diagram. The AC inlet socket is a

standard IEC type. You will need to obtain the correct type for your region.

Installing the source input:

Plug the RCA interconnection cable into the RCA connectors; see ③in the below diagram. Or,

plug the XLR interconnection cable into the XLR connectors; see ④in the below diagram.





U.S.

European

U.K.

Switch to label “115” for

AC100 to 125V voltage.

Switch to label “230” for

AC210 to 240V voltage.



Replacing the fuse when needed:

The fuse is located on the same unit of the AC inlet.

Back panel diagram:



①AC Inlet with fuse box

②Voltage selection switch

③RCA connectors

④XLR connectors

⑤RCA, XLR selector

Insert a small flat

screwdriver into

the fuse door

which located on

the AC inlet.

Release the fuse

door by pulling it

out.

The fuse holder is

released from the

AC inlet.

The fuse is held by

a clip.





Operation

DO NOT

oTurn on the amp before properly installing ALL tubes.

oUse tubes that are not approved by Woo Audio.

oTurn on the equipment without checking the correct AC voltage setting.

oRemove any tubes or the DC cord while the amp is operating.

oTouch tubes (extremely hot) after warm-up.

oLeave the amp running unattended. To use the amp safely, please allow it to cool

down for every 8 hours of continuous play time.

oPlace the amp away from any wireless or frequency-emitting devices, such as

mobile phones, PDAs and radios, to avoid noise interference.

oKeep away from water or excessive moisture.

oTurn off the amp if its sound is abnormal.

oAllow a minimum of 2 inches of air clearance for heat dissipation.

oAllow approximately 5 minutes of warm-up.

oAllow the tubes to cool down before replacing them.



Turning the amplifier on:

1. Turn the volume knob ①to the lowest position.

2. Insert a headphone into either ②,or③,or④output.

3. Turn the power switch knob ⑤from OFF to HI or OFF to LO position. Then, the power

LED will pulsate for approx 20 seconds.

4. Observe that all tubes light gradually.

5. Wait until the LED ⑥ becomes solid and let the tubes warm up for at least 1 minute

before turning up the volume.

Front panel diagram:

①Volume control

②3-pin XLR headphone output, Left and Right channel.

③4-pin XLR headphone output

④TRS (¼” or 6.35mm) headphone output

⑤Multi-functional switch for power switch and high/low impedance selection

⑥PowerLED indicator

Break-in period:

It is recommended to allow the amplifier to operate 150+ hours so that peak performance can be

realized. An effective way to break in the amp is to run the amp normally with music playing.

Please do not leave the amp running continuously.

Tabla de contenidos

Otros manuales de Amplificador de Woo Audio

Woo Audio

Woo Audio WA5 Manual de usuario

Woo Audio

Woo Audio WA5 Manual de usuario

Woo Audio

Woo Audio WA2 Manual de usuario

Woo Audio

Woo Audio WA23 LUNA Manual de usuario

Woo Audio

Woo Audio WA-5 300B Manual de usuario

Woo Audio

Woo Audio WA7 Fireflies Manual de usuario

Woo Audio

Woo Audio WA7 Fireflies Manual de usuario

Woo Audio

Woo Audio WA6-SE Manual de usuario

Woo Audio

Woo Audio WA11 topaz Manual de usuario

Woo Audio

Woo Audio WES Manual de usuario

Woo Audio

Woo Audio WA7d Manual de usuario

Woo Audio

Woo Audio WA6 Manual de usuario

Woo Audio

Woo Audio WA3 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario