Wolf MWD24-2U/S Manual de usuario

IN S TA L L AT I O N IN S T RU C T I O N S

DR A W E R MI C R O W A V E

As you follow these instructions, you will

notice WARNING and CAUTION symbols.

This blocked information is important for the

safe and efficient installation of Wolf equip-

ment. There are two types of potential

hazards that may occur during installation.

Another footnote we would like to identify is

IMPORTANT NOTE: This highlights informa-

tion that is especially relevant to a problem-

free installation.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF®is a registered trademark of Wolf Appliance, Inc.

CO N TA C T

INFORMATION

Wolf Customer

Service:

800-332-9513

Website:

wolfappliance.com

Any questions or problems regarding the

installation should be directed to your dealer

or Wolf Appliance, Inc. at 800-332-9 13. You

can also visit our website, wolfappliance.com.

C L E A R A N C E S A N D D I M E N S I O N S

R AT I N G P L A T E L O C A T I O N

Record the model and serial numbers before

installing the drawer microwave. Both

numbers are listed on the product rating plate.

Refer to the illustration below.

The rating plate includes model and serial

number. Open the drawer fully. The label is

slightly beyond the back wall of the

microwave cavity facing up from the flat

surface.

W O L F D R AW E R M I C R OWAV E

Rating plate location

RAT I N G P L AT E

INFORMATION

Model Number

Serial Number

I N S TA L L AT I O N REQUIREMENTS

IMPORTANT NOTE:

This installation must be

completed by a qualified installer or Wolf

authorized service center technician. Save this

installation manual for local electrical inspec-

tor’s use. Read and save these instructions for

future reference.

INSTALLER

Read all of the Installation Instructions

before installing the drawer microwave.

Remove all packing material before

connecting the electrical supply.

Observe all governing codes and ordi-

nances.

Be sure to leave these instructions with the

consumer.

C O N S U M E R

Keep this manual with your Use & Care Guide

for future reference.

As when using any microwave oven gener-

ating heat, there are certain safety precau-

tions you should follow. These are listed in

the Use & Care Guide. Read all and follow

carefully.

Be sure your drawer microwave is installed

and grounded properly by a qualified

installer or service technician.

For safety considerations do not install

drawer in any combustible cabinetry,

which is not in accord with the stated

clearances and dimensions on pages 6–8.

Rating plate: Open the

drawer fully. The label is

slightly beyond the back

wall of the microwave

cavity facing up from the

flat surface.

W O L F D R AW E R M I C R OWAV E

IMPORTANT SAFETY I N S T R U C T I O N S

If the information in this manual is not

followed exactly, a fire or electrical shock

may result that could cause property

damage, personal injury or death.

To reduce the risk of tipping, the drawer

microwave must be secured by a

properly installed Anti-Tip block.

This drawer microwave must be electri-

cally grounded in accordance with local

codes.

Make sure the wall coverings and the

cabinets around the drawer microwave

can withstand the heat generated by the

drawer microwave.

Never leave children alone or unattended

in the area where a drawer microwave is

in use. Never leave the drawer open

when the microwave is unattended.

Stepping, leaning or sitting on the

drawer may result in serious injuries and

can also cause damage to the drawer

microwave.

Do not use the drawer microwave as a

storage space. This creates a potentially

hazardous situation.

Check that the time-of-day is in the

display. If not, touch Stop/Clear to

prevent unintended use.

I N S TA L L AT I O N I N S T R U C T I O N S

U N PAC K I N G Y O U R M I C R O WA V E

Remove all packing materials from inside

the drawer microwave.

Do not remove the

waveguide cover,

which is located on the

top of the drawer microwave.

Remove the feature sticker, if there is one.

Check the drawer for any damage, such as

misaligned or bent drawer, damaged

drawer seals and sealing surfaces, broken

or loose drawer guides and dents inside the

cavity or on the front side of the drawer. If

there is any damage, do not operate the

drawer microwave and contact your dealer

or a Wolf authorized service center.

Refer to the illustrations below.

C L E A R A N C E S A N D D I M E N S I O N S

Dimensions shown on the following pages

must be used. Given dimensions provide

minimum clearance. Locate electrical outlet

in the shaded area in the upper left-hand

corner of the cutout. See page 9.

Contact surface must be solid and level. Pay

special attention to the floor on which the

drawer microwave will sit. The floor of the

opening should be constructed of plywood

strong enough to support the weight of the

oven, about 100 pounds (4 kg).

Check location where the drawer

microwave will be installed for proper elec-

trical supply.

Your oven can be built into a cabinet or wall

by itself or under a gas or electric wall

oven.

Be sure that the clearance of the floor

between the wall oven and the drawer

microwave is a minimum of 2" ( 1).

The microwave interior will easily accom-

modate a 9" (229) x 13" (330) oblong dish or

a bag of microwave popcorn.

The trim will overlap cabinetry by 7/16" (11)

at the top, 1/8" (3) at the bottom and 3/4" (19)

on each side.

Dimensions in parentheses are in

millimeters unless otherwise specified.

Waveguide cover

Sealing surface Sealing surface

Oven cavity

Waveguide cover location Sealing surface location

Dimensions in parentheses are in

millimeters unless otherwise specified.

W O L F D R AW E R M I C R OWAV E

24" (610) DRAWER M I C R OWAV E

OVERALL DIMENSIONS

INSTALLATION SPECIFICATIONS

Standard Installation

Flush Inset Installation

221/8"(562)

OPENING WIDTH

27" rec (686)

24" min (610)

CABINET WIDTH

231/2"min (597)

OPENING DEPTH

36" (914)

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

2" (51)

24" min (610)

CABINET DEPTH

31/2"(89) x 2"(51)

ANTI-TIP BLOCK

143/4"(375)

OPENING

HEIGHT

Dashed lines represent profile of unit.

FRONT VIEWSIDE VIEW

5/8"(16) PLATFORM

243/8"(619)

FLUSH INSET WIDTH

221/8"(562)

OPENING WIDTH

11/8"(29)

SIDE CLEATS

7/16"(11) PLATFORM

7/16"(11)

TOP CLEAT

27" rec (686)

24" min (610)

CABINET WIDTH

SIDE CLEATS

243/4"min

(629)

FLUSH

INSET

DEPTH

11/4"

(32)

36" (914)

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

19/16"(38)

25" min (635)

CABINET DEPTH

1515/16"

(405)

FLUSH INSET

HEIGHT

31/2"(89) x 2"(51)

ANTI-TIP BLOCK

15" (381)

OPENING

HEIGHT

Dashed line represents profile of unit.

FRONT VIEWSIDE VIEW

TOP VIEW

233/8"(594)

BEHIND FRAME

157/16"

(392)

237/8"(606)

219/16"(548)

149/16"

(370)

233/8"

(594)

237/8"(606)

POWER

CORD

CHANNEL

11/4"

(32)

411/16"

(119)

13/4"

(44)

161/2"

(419)

The drawer microwave

can also be installed

using an electrical

outlet in an adjacent

cabinet within the area

where the provided

electrical cord can

reach. Power cord

access hole in cabinet

should be a minimum

11/2" (38) diameter

hole and deburred of

all sharp edges.

IMPORTANT NOTE:

Always allow sufficient

power cord length to

the electrical outlet to

prevent tension.

Always chec electrical

codes for requirements.

I N S TA L L AT I O N I N S T R U C T I O N S

3 0 " ( 7 6 2 ) DRAWER M I C R OWAV E

OVERALL DIMENSIONS

INSTALLATION SPECIFICATIONS

Standard Installation

Flush Inset Installation

287/16"(722)

OPENING WIDTH

231/2"min (597)

OPENING DEPTH

33" rec (838)

30" min (762)

CABINET WIDTH

36" (914)

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

2" (51)

24" min (610)

CABINET DEPTH

31/2"(89) x 2"(51)

ANTI-TIP BLOCK

143/4"(375)

OPENING

HEIGHT

Dashed lines represent profile of unit.

FRONT VIEWSIDE VIEW

5/8"(16) PLATFORM

36" rec (914)

33" min (838)

CABINET WIDTH

303/8"(772)

FLUSH INSET WIDTH

281/2"(724)

OPENING WIDTH

1"(25)

SIDE CLEATS

7/16"(11) PLATFORM

7/16"(11) TOP CLEAT

SIDE CLEATS

243/4"min

(629)

FLUSH

INSET

DEPTH

11/4"

(32)

36" (914)

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

19/16"(38)

25" min (635)

CABINET DEPTH

15" (381)

OPENING

HEIGHT

1515/16"

(405)

FLUSH INSET

HEIGHT

31/2"(89) x 2"(51)

ANTI-TIP BLOCK

Dashed line represents profile of unit.

FRONT VIEWSIDE VIEW

TOP VIEW

233/8"(594)

BEHIND FRAME

157/16"

(392)

297/8"(759)

281/8"(714)

POWER

CORD

CHANNEL

11/4"

(32)

411/16"

(119)

(51)

149/16"

(370)

233/8"

(594)

161/2"

(419)

297/8"(759)

The drawer microwave

can also be installed

using an electrical

outlet in an adjacent

cabinet within the area

where the provided

electrical cord can

reach. Power cord

access hole in cabinet

should be a minimum

11/2" (38) diameter

hole and deburred of

all sharp edges.

IMPORTANT NOTE:

Always allow sufficient

power cord length to

the electrical outlet to

prevent tension.

Always chec electrical

codes for requirements.

W O L F D R AW E R M I C R OWAV E

30" (762) DRAWER M I C R OWAV E

273/16"

(691)

OPENING

HEIGHT

281/2"min

(724)

FLUSH

INSET

HEIGHT

281/2"(724)

ESERIES OVEN

OPENING WIDTH

36" rec (914)

33" min (838)

CABINET WIDTH

25" min (635)

CABINET DEPTH

303/8"min (772)

FLUSH INSET WIDTH

281/2"(724)

DRAWER MICROWAVE

OPENING WIDTH

SIDE VIEW

19" (483)

TO FLOOR

(typical)

7/8"(22) TOP CLEAT

5/16"(8) PLATFORM*

7/16"(11) PLATFORM

SIDE CLEATS

243/4"min

(629)

FLUSH

INSET

DEPTH

11/4"(32)

FOR DRAWER

MICROWAVE

1" (25) FOR

ESERIES OVEN

*Platform must be able to support 250 lbs (113 kg). Refer to the 30" (762) E Series built-in oven specifications for electrical location.

Dashed lines represent profile of unit.

FRONT VIEWSIDE VIEW

TOP VIEW

15" (381)

OPENING

HEIGHT

1515/16"

(405)

FLUSH INSET

HEIGHT

1"(25)

SIDE CLEATS

1"(25)

SIDE CLEATS

The drawer microwave

can also be installed

using an electrical

outlet in an adjacent

cabinet within the area

where the provided

electrical cord can

reach. Power cord

access hole in cabinet

should be a minimum

11/2" (38) diameter

hole and deburred of

all sharp edges.

IMPORTANT NOTE:

Always allow sufficient

power cord length to

the electrical outlet to

prevent tension.

Always chec electrical

codes for requirements.

INSTALLATION SPECIFICATIONS

Installation below a

Wolf E Series Built-In Oven

Dimensions in parentheses are in

millimeters unless otherwise specified.

I N S TA L L AT I O N I N S T R U C T I O N S

A N T I - T I P B L O C K

INSTALL ANTI-TIP BLOCKING

To reduce the risk of tipping of the drawer, the

Anti-Tip block must be properly installed

located 1413/16" (376) above the floor on which

the drawer microwave will sit. The 6" (1 2)

Anti-Tip block must be provided by the

installer. See pages 6–7. The Anti-Tip block

prevents serious injury that might result from

spilled hot liquids.

If the drawer microwave is ever moved to a

different location, the Anti-Tip block must also

be moved and installed. When installed to the

wall, make sure that the screws completely

penetrate the dry wall and are secured in wood

or metal so that the block is totally stable.

When fastening, be sure that the screws do not

penetrate electrical wiring or plumbing.

E L E C T R I C A L R E Q U I R E M E N T S

E L E C T R I C A L O U T L E T L O C A T I O N

The electrical requirements are a 120 volt 60

Hz, AC only, 1 amp or more protected electri-

cal supply. It is recommended that a separate

circuit serving only this appliance be provided.

The drawer is equipped with a 3-prong

grounding plug. It must be plugged into a wall

receptacle that is properly installed and

grounded. Should you only have a 2-prong

outlet, have a qualified electrician install a

correct wall receptacle.

NOTE:

If you have any questions about the

grounding or electrical instructions, consult a

qualified electrician or service person.

(102)

5" (127)

Electrical Outlet

Location

Anti-tip

Block

6" (153)

Electrical OutletAnti-tip block

IM P O R TA N T

N O T E

You must follow

all National

Electrical Code

regulations. In

addition, be aware

of local codes and

ordinances when

installing your

service.

Dimensions in parentheses are in

millimeters unless otherwise specified.

W O L F D R AW E R M I C R OWAV E

ELECTRICAL REQUIREMENTS

GROUNDING

I N S T R U C T I O N S

This appliance must be grounded. The drawer

microwave is equipped with a cord having a

grounding wire with a grounding plug. It must

be plugged into a wall receptacle that is

properly installed and grounded in accordance

with the National Electrical Code and local

codes and ordinances. In the event of an elec-

trical short circuit, grounding reduces risk of

electric shock by providing an escape wire for

the electric current.

Mounting

Flange

4 screws provided

Drawer installation

3-Prong Plug

Grounding Pin

3-Prong Receptacle

Ground Receptacle Box

Grounding

Improper use of the grounding plug can

result in a risk of electric shock. Do not

use an extension cord. If the power

supply cord is too short, have a qualified

electrician or serviceman install an outlet

near the appliance.

IM P O R TA N T

N O T E

You must follow

all National

Electrical Code

regulations. In

addition, be aware

of local codes and

ordinances when

installing your

service.

D R AW E R I N S T A L L AT I O N

Place the drawer adjacent to the wall or

cabinet opening. Plug the power supply

cord into the electrical outlet.

Carefully guide the drawer into the

prepared opening. Avoid pinching the cord

between the oven and the wall.

Slide the drawer all the way until the

mounting flange is flush with the face of

the cabinet. See illustration below.

)

Open the drawer. Using the 4 holes on the

drawer as a template, pre drill the cabinet

using a 1/16" (1.6) bit. See illustration below.

Secure the drawer with the 4 screws

supplied. See illustration below.

Otros manuales para MWD24-2U/S

Tabla de contenidos

Otros manuales de Microondas de Wolf

Wolf

Wolf MWD24-2U/S Manual de usuario

Wolf

Wolf 1200154 Instrucciones de funcionamiento

Wolf

Wolf Drawer Microwave Oven Manual de usuario

Wolf

Wolf MWD24-2U/S Manual de usuario

Wolf

Wolf M Series Manual de usuario

Wolf

Wolf SO30F/S Guía

Wolf

Wolf MWC24 Manual de usuario

Wolf

Wolf MWD24-2 Manual de referencia

Wolf

Wolf MW24 Manual de servicio

Wolf

Wolf CONVECTION MICROWAVE OVEN WITH GRILL Manual del propietario

Wolf

Wolf MWC24 Instrucciones de uso

Wolf

Wolf MWD30-2F/S Manual de usuario

Wolf

Wolf MDD24TESTH Guía de inicio rápido

Wolf

Wolf ICBMDD30TM Manual de usuario

Wolf

Wolf ICBMW30-240 Manual del propietario

Wolf

Wolf MWD24-2U/S Manual de usuario

Wolf

Wolf Drawer Microwave Oven Manual de usuario

Wolf

Wolf M I C R O W AV E O V E N Manual del propietario

Wolf

Wolf MC24 Manual de usuario

Wolf

Wolf MWC24 Instrucciones de uso

Wolf

Wolf Drawer Microwave Oven Manual de usuario

Wolf

Wolf e Series Manual de usuario

Wolf

Wolf MWD30-2F/S Manual de usuario

Wolf

Wolf MWD24-2U Manual de usuario

Manuales populares de Microondas de otras marcas

Daewoo

Daewoo KOG-574R0S Manual de usuario

LG MH7040SS Manual de usuario

Sharp

Sharp R-895(AL)M Manual de usuario

Dometic

Dometic DOTRM13W Manual de usuario

Sanyo

Sanyo EM-X680 Manual de usuario

Sharp

Sharp R-393M Manual de usuario

KitchenAid

KitchenAid KMCX4510 Instrucciones de instalación

Smeg

Smeg S45MCX1 Manual de usuario

Russell Hobbs

Russell Hobbs RHM2044 Manual de usuario

Sunbeam

Sunbeam SMW759 Manual de usuario

Gallet

Gallet FMOE230S Manual de usuario

Bosch

Bosch CEG732X.1B Manual de usuario

Dometic

Dometic Roadmate 230 Manual de usuario

Samsung

Samsung SJ0396W Manual de usuario

Sanyo

Sanyo EM-P494WS Manual de usuario

Sharp

Sharp R-240 Manual de usuario

Electrolux

Electrolux EMS2840 Manual de usuario

Daewoo

Daewoo KOC-984T2S13 Manual de usuario