WIRE SOURCE
WIRE WIZARD
®
GUIDE MODULE INSTALLATION COMPONENTS
See our website for additional parts www.wire-wizard.com
RUN TO WELD CELL AND/OR ADDITIONAL MODULES
CELL WALL MOUNTING OPTIONS
WELD CELL MOUNTING OPTIONS & ACCESSORIES
WIRE FEEDER
End Cap A
WGM-ECK-25 1/4" NPT End Cap Kit
Use only with A-4-ST Disconnect
Recommended for most applications:
WGM-ECK-50 1/2" NPT End Cap Kit
Use w/ A-10HM, A-10XM, A-10RM or WGM-A-5
A-10HM
A-10XM
For EC-3R or FC-X-SW Conduit,
use WGM-A5 Quick Disconnect Here
EC-4-R Conduit Assembly
FC-X Conduit Assembly
A-10RMFC-XH or EC-5 Conduit
Wood Reel
with Wire
Guide Arm
Drum or Box
WWDP
Direct
Pull Kit
WGM-DK
Drum Mounting Kit
WGM-HSK
Drum Hood Swivel Kit
WGM-021
Support Bracket
WGM-024 Slotted
Support Bracket
WGM-025 45° Angle
Support Bracket
WGM-UAK 360° Union Adapter Kit
WGM-A-10BK Face Mount Bracket Kit Allows 360° adjustment on single side
WGM-WK-2-1 Cell Wall Mounting Kit, Double Sided
WGM-WK-1-1 Cell Wall Mounting Kit, Single Sided
WGM-A-10BK with WGM-A5
Assembled on Module
WGM-UAK Assembled
(Modules attach on
both sides)
WGM-WK-1-1
Assembled
WGM-WK-2-1
Assembled
90° GUIDE MODULE KIT
WGM-90K inc. 1/2” End Caps
Other kits available include
WGM-135K (135° kit) and
WGM-180K (180° kit)
Assembled 90°
with End Caps
WGM-LBM-BRKT
L-Bracket Mounting Kit
WGM-1 (Single WGM)
WGM-LBM-BRKT
Assembly
HANGING BRACKETS
END CAP OPTIONS
Each end cap kit contains one
A and one B end cap
WGM-1-BRKT
45° Hanger Kit
WGM-1-90-BRKT
90° Hanger Kit
10" (254mm) to
18" (457mm)
Allows 360° adjustment on both sides
Pivots upward to allow easy wire feeding from drums & reels
20" (508mm) to
36" (914mm)
SETUP FOR MEZZANINE APPLICATION
CELL MOUNTING BRACKET OPTIONS FOR INTERIOR OR EXTERIOR OF CELL
1/4" NPT
1/2" NPT
Strain Relief Connector
(Recommended)
Inlet Guide
360°
Rotation
End Cap B
5750 Marathon Drive • Jackson, MI 49201 • (517) 782-8040 • Fax (517) 782-8039
www.wire-wizard.com
End
Cap A
Tools Required: WGM-1 Kit Contents: End Cap Kit Contents:
(1) 45° module (1) “A” style end cap with threaded insert
(2) Intermediate fasteners (1) “B” style end cap with threaded insert
(1) Intermediate pilot pin (4) End cap fasteners
Assembly of 90°, 135° and 180° Guide Modules
Step 1: Connecting Modules (for 90°, 135° or 180° turn)
Insert intermediate pin in one end of module until it firmly
seats (Step 1-A). Connect the two modules using the interme-
diate pin and ears to align the modules together (Step 1-B).
Use the intermediate fasteners to lock modules together.
Continue connecting modules until you have the proper
bend radius. If only a 45° turn is required (one module), or if
using a WGM-M-1 Mini 90°, simply connect the end caps.
Step 2: Connecting End Caps
Connect the appropriate end cap as shown. Insert and
tighten the end cap fasteners to lock in place. Repeat with
the other end cap. Insert pins for the end caps are only
required when using the A-10RM or A-10XM fittings (caps will
be included with fitting).
Step 3: Adding End Cap Fittings & Connecting Conduit
Pass Through Compression Fitting: Thread the pass-through
compression fitting into the appropriate end cap. Debur and
countersink the conduit out to the conduit edge (a counter-
sink tool for polymer conduit, part # EC-DB, is available from
ELCo Enterprises). If you are using EC-4-R polymer conduit,
you may push the conduit directly into the module, however
be sure to countersink the ends or wire may not feed proper-
ly. Push the conduit through the compression nut until the
conduit stops at the inlet inside the module. Pull the conduit
back approx. 0.25” inches (6 mm). Tighten compression nut.
Doing so will pull the conduit to the face of the end cap pin
without crushing it.
WGM-A5 Quick Disconnect Option: Thread quick disconnect
into the appropriate end cap and attach conduit.
Last Revised: 12/15/15
90° GUIDE
MODULE
ASSEMBLY
WIRE GUIDE MODULE & END CAP ASSEMBLIES
GUIDE MODULE ASSEMBLY INSTRUCTIONS
STEP 1-A STEP 1-B
Insert Fasteners
Insert Pin
Between
Modules
Pull conduit back 0.25” (6 mm)
prior to tightening
STEP 3: Compression Fitting STEP 3: Quick Disconnect
(pt. # WGM-A5)
Intermediate
Pin
(2) 8mm wrenches*
(1) Conduit Cutter* (pt. #EC-CUTTER)
(1) Countersink Tool* (pt. #EC-DB)
*All required tools also available in the Guide Module Assembly Tool Kit, part #WGM-ATK
WGM-044 Weld /
Bolt-on Bracket
WGM-A5 Insulated
QD Adapter Kit
End
Cap B
WGM-A5
Quick
Disconnect
Compression Fittings
Always countersink
conduit ends to avoid
wire hang-ups.
Countersink tool
available, pt. #EC-DB
45° GUIDE
MODULE
ASSEMBLY
FITTING CONDUIT
A-10HM EC-4-R or FC-E
A-10XM FC-X
A-10RM FC-XH or EC-5
End
Cap A
End
Cap B
Part #
WGM-3-BRKT
Side Mount Bracket
Adjustable
height from
50" –86"
(1.3-2.2m)
Adjustable
arm length
from 4" –19"
(102-483mm)
Wire Wizard®
Fire Resistant
Drum Covers &
Dollies Available
Drum -or-
Wood Reel
Additional
arm, part #
WGM-PFA-
STAND-
ARM
Part #
WGM-PFA-STAND
Conduit to wire feeder
WWDP
Direct
Pull Kit
A-10HM EC-4-R Conduit >>
A-10XM FC-X Conduit >>
A-10RM FC-XH / EC-5 Conduit >>
Use disconnect for other conduit sizes
WGM-FLM
Floor
Mounting
Bracket
WGM-FSK-14
Wire Feeder Swivel Kit
Creates 360° rotation point
at the feeder disconnect
WGM-EA-10 & WGM-EA-20 Adjustable Extension Arms (also see pt. #WGM-CM-1)
