Winmate R19IHAT-66EX Manual de usuario

Full IP66 Aluminum

Flat Touch SeriesPanel PC

R19IHAT-66EX for ATEX Zone II and C1D2

R19IHAT-66EX

User Manual

Document Version 11.0

Document Part No. PPM201404282

R19IHAT-66EX User Manual

Contents

Preface 3

Chapter 1: Introduction 7

1.1 Overview 7

1.2 Features 7

1.3 Package Contents 8

1.4 Product Overview 9

1.5 Front Buttons 10

Chapter 2: Getting Started 11

2.1 Turning On Your Device 11

2.2 Adjusting the LCD DisplayBrightness 12

2.3 Turning Off Your Device 12

Chapter 3: Installation 13

3.1 Wiring Requirements 13

3.2 Wiring 14

3.3 Pin Assignments 16

Chapter 3: Mounting Solution 21

3.1 Clamp Mount 21

3.2 VESA Mount 22

Chapter 4: Windows 7 Driver Installation 23

4.1 Chipset Driver Installation 23

4.2 Graphic Driver Installation 25

4.3 USB 3.0 Driver Installation 27

4.4 Ethernet Driver Installation 30

4.5 Audio Driver Installation 31

4.6 Fintek COM Port Driver Installation 32

4.7 Intel Management Engine Software Installation 35

4.8 HotTab Driver and AP Installation 37

4.9 Hottab Utility 43

4.9.1 System information menu 44

4.9.2 Hottab Shortcut Setting 44

4.10 Touch Lock Setting 46

4.11 Brightness Adjustment 47

Appendix 48

Appendix A: Hardware Specifications 48

Appendix B: Cleaning the Monitor 41

Appendix B: Statement of RegulatoryApproval 41

Preface

No part of this document may be reproduced, copied, translated, or transmitted in any form or by

any means, electronic or mechanical, for any purpose, without the prior written permission of the

original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer

We reserves the right to make changes, without notice, to any product, including circuits and/or

software described or contained in this manual in order to improve design and/or performance. We

assume no responsibility or liability for the use of the described product(s), conveys no license or title

under any patent, copyright, or masks work rights to these products, and makes no representations or

warranties that these products are free from patent, copyright, or mask work right infringement,

unless otherwise specified. Applications that are described in this manual are for illustration purposes

only. We make no representation or warranty that such application will be suitable for the specified

use without further testing or modification.

Warranty

Our warranty that each of its products will be free from material and workmanship defects for a period

of one year from the invoice date. If the customer discovers a defect, we will, at its option, repair or

replace the defective product at no charge to the customer, provided it is returned during the warranty

period of one year, with transportation charges prepaid. The returned product must be properly

packaged in the original packaging to obtain warranty service.

If the serial number and the product shipping data differ by over 30 days, the in-warranty service

will be made according to the shipping date. In the serial numbers the third and fourth two digits

give the year of manufacture, and the fifth digit means the month (e. g., with A for October, B for

November and C for December).

For example, the serial number 1W08Axxxxxxxx means October of year 2008.

R19IHAT-66EX User Manual

Customer Service

We provide service guide for any problem as follow steps: First, visit the website of our distributor to

find the update information about the product. Second, contact with your distributor, sales

representative, or our customer service center for technical support if you need additional assistance.

You may have the following information ready before you call:

•

Product serialnumber

•

Peripheral attachments

•

Software (OS, version, application software, etc.)

•

Description of completeproblem

•

The exact wording of any errormessages

In addition, free technicalsupport is available from our engineers every business day. We are

always ready to give advice on application requirements or specific information on the

installation and operation of any of our products. Please do not hesitate to call or e-mail us.

Safety Information

WARNING!

Always completely disconnect the power cord from your chassis whenever

you work with the hardware. Do not make connections while the power is

on. Sensitive electronic components can be damaged by sudden power

surges. Only experienced electronics personnel should open the PC

chassis.

CAUTION!

Always ground yourself to remove any static charge before touching the

CPU card. Modern electronic devices are very sensitive to static electric

charges. As a safety precaution, use a grounding wrist strap at all times.

Place all electronic components in a static-dissipative surface or static-shielded bag when

they are not in the chassis.

Safety Precautions

•

Please read these safety instructionscarefully.

•

Please keep this user’s manual for later reference.

•

Please disconnect this equipment from any AC outlet before cleaning. Do not use liquid

or spray detergents for cleaning. Use a damp cloth.

•

Do not touch the LCD panel surface with sharp or hard objects.

•

For pluggable equipment, the power outlet must be installed near the

equipment and must be easily accessible.

•

Keep this equipment away fromhumidity.

•

Place this equipment on a reliable surface during installation. Dropping it or letting it

fall could cause damage.

•

The openings on the enclosure are for air convection. Protect the equipment from overheating.

DO NOT COVER THE OPENINGS.

•

Make sure the voltage of the power source is correct before connecting the equipment to

Preface

the power outlet.

•

Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

•

All cautions and warnings on the equipment should be noted.

•

If the equipment is not used for a long time, disconnect it from the power source

to avoid damage by transientover-voltage.

•

Never pour any liquid into an opening. This could cause fire or electrical shock.

•

Never open the equipment. For safety reasons, only qualified service personnel should

open the equipment.

•

This equipment is designed to be used in restricted access location. Only service persons or

trained persons are allowed to access this equipment.

•

If any of the following situations arises, get the equipment checked by service personnel:



The power cord or plug isdamaged.



Liquid has penetrated into the equipment.



The equipment has been exposed to moisture.



The equipment does not work well, or you cannot get it to work according to the user’s

manual.



The equipment has been dropped and damaged.



The equipment has obvious signs ofbreakage.

•

Do not leave this equipment in an uncontrolled environment where the storage temperature is

below

-20°C (-4°F) or above 70°C (158°F). It may damage the equipment.

•

Ne laissez pas ce matériel dans un environnement non contrôlé où la température de

stockage est inférieure à -20 ° C ( -4 ° F ) ou au-dessus de 70 ° C ( 158 ° F ) . Il peut

endommager lematériel.

•

CAUTION –Use recommended mounting apparatus to avoid risk ofinjury.

•

ATTENTION - Utilisez recommandé appareil de montage pour éviter les risques de blessure.

•

WARNING –Only use the connection cords which comes along with the product,

when in doubt, please contact the manufacturer.

•

ATTENTION - Utilisez uniquement les cordons de connexion qui vient avec le produit

, en cas de doute , s'il vous plaît contactez le fabricant.

•

Provision shall be made to provide transient protection device to be set at a level not

exceeding 140% of the rated voltage at the power supply terminals of the apparatus.

•

Des dispositions seront prises pour fournir dispositif de protection contre les transitoires à

être fixé à un niveau ne dépassant pas 140 % de la tension nominale aux bornes

d'alimentation del'appareil.

•

WARNING –Explosion Hazard –Do not disconnect equipment unless power has been

switched off or the area is known to be non-hazardous.

•

AVERTISSEMENT - Risque d'explosion - Ne débranchez pas l'équipement que

l'alimentation est coupée ou que la zone est connue pour être non dangereux

•

WARNING –Explosion Hazard –Do not apply any audio connectors in Hazardous Location.

•

AVERTISSEMENT - Risque d'explosion - Ne pas appliquer tous les connecteurs audio

dans des environnements dangereux .

•

WARNING –The equipment should be adequately protected from direct light when

installed indoor or outdoor.

R19IHAT-66EX User Manual

•

AVERTISSEMENT - L'équipement doit être adéquatement protégé de la lumière

directe lors de l'installation intérieure ou extérieure.

•

WARNING –DO NOT OPEN, MAINTAIN OR SERVICE IN AN AREA WHERE AN

EXPLOSIVE ATMOSPHERE MAY BE PRESENT.

•

AVERTISSEMENT - NE PAS OUVRIR , maintenir ou SERVICE DANS UN ENDROIT

OÙ UNE ATMOSPHERE EXPLOSIVE PEUT ETRE PRESENTE .

•

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C,D

OR NON-HAZARDOUS LOCATIONS ONLY.

•

Cet équipement est utilisable en Classe I, Division 2, Groupes A,

B , C ,D LIEUX OU non dangereux.

•

WARNING - EXPLOSION HAZARD –SUBSTITUTION OF COMPONENTS MAY IMPAIR

SUITABILITY FOR CLASS I, DIVISION 2;

•

AVERTISSEMENT - RISQUE D'EXPLOSION - substitution de composants peut nuire à la conformité

Classe I, Division 2 ;

•

WARNING - EXPLOSION HAZARD - DO NOT REPLACE PARTS UNLESS POWER HAS BEEN

SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS;

•

AVERTISSEMENT - RISQUE D'EXPLOSION - NE PAS remplacer les pièces que l'alimentation est

coupée ou que la zone est connue pour être non dangereux;

•

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS

POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-

HAZARDOUS;

•

AVERTISSEMENT - RISQUE D'EXPLOSION - NE PAS déconnecter l'équipement que

l'alimentation est Coupée ou la région est connue pour être non dangereux;

•

WARNING - Do not use USB Port while the hazardous atmosphere is present.

•

AVERTISSEMENT - Ne pas utiliser le port USB tandis que l'atmosphère dangereuse est présente.

Specific Conditions of Use

Contradicts IEC 60079-0:2011 clause 8.3 for EPL Gc

WARNING – In locations where high external humidity and internal temperature variations

(e.g. frequent on-off cycles) may cause condensation inside the equipment, the interior

should be periodically inspected.

When installed, the equipment shall be subjected to an electric strength test using a test

voltage of 500 Vac applied between the circuit and earth for 60 s. Alternatively, a voltage of

20% higher may be applied for 1 s. There shall be no evidence of flashover or breakdown

and the maximum current flowing shall not exceed 5 mA.

When the device is mounted in a hazardous area, connection and disconnection of the

connectors while live is only permitted if the potentially explosive atmosphere is shown to be

absent.

The “9-36” Vdc rated supply shall be protected such that transients are limited to a maximum

of 60Vac or 85 Vdc; no such protection is required for the signal lines.

When the equipment is installed in a location where the ambient temperature is expected to

exceed 55ºC, the cable shall have a temperature rating of 85ºC minimum.

General Guideline

It is recommended to reboot the device when some functions are defect or inactive. If it still

can't solve the problems please contact your dealer or agent.

Chapter 1: Introduction

1.1 Overview

Class1 Division2 certification for equipment was created to ensure employee safety in explosive

atmospheres. Today many countries have made it a requirement for organizations operating in certain

industries to use equipment that meets the regulatory compliance. This includes technologies used in

potentially explosive atmospheres. The Winmate 19” HazLoc PPC is the first of its kind to offer the Class1

Division2 certification, ensuring safe and reliable data collection and processing in Hazardous Locations.

This Panel PC features robust processing power with the 2.6GHz Intel Haswell Core i5-4300U. The panel

PC also offers brilliant visibility with its true flat design, transflective sunlight-viewable, projected

capacitive touchscreen with 1280 x 1024 pixel resolution, all in a compact form factor

1.2 Features

•

Intel® Haswell Core i5-4300U, turbo max 2.6 GHz

•

19” SXGA High brightness panel, 800 nits

•

Sunlight readable, transflective, projected capacitive touch LCD panel

•

Fanless, streamlined enclosure for highly efficient heat dissipation

•

Front side buttons, one dedicated button to enable/disable touch screen interface

•

Built in to withstand extreme temperatures -40 to 70 deg. C with built in intelligent heater and

wide range temperature memory parts

•

9-36 V DC input with isolation (There is no tolerance for the DC input voltage)

•

Operable in 5-95% humidity level

R19IHAT-66EX User Manual

1.3 Package Contents

Before using this Panel PC, please make sure that all the items listed below are present in your package:

Standard Accessories:

Before using this Panel PC, please make sure that all the items listed below are present in your package:

Panel PC

24V 150W AC to DC

Power adapter

(for Testing only)

Power cord

Open wire power cable

LAN + COM combo cable

Manual & Driver DVD

VESA Mounting

Screws

Mounting Clips & Screws

3 Pins Terminal Block For

Power

8 Pins Terminal Block For

LAN

4 Pins Terminal

Block For USB

10 Pins Terminal Block

For COM

Touch Driver CD

(C1D2 Version)

Chapter 1: Introduction

Optional Accessories:

Wi-Fi Antenna extension

cable (Optional)

Side Handle

(Optional)

Note: All cables are for testing only, Do Not use these cables under Hazardous area.

1.4 Product Overview

(Unit: mm)

Front View

R19IHAT-66EX User Manual

1.5 Front Buttons

Front Button & LED Indicators

Power on/off

Increase the brightness of the Panel

Decrease the brightness of the Panel

Suspend the touch’s function temporarily

Programmable function key configured by Hot Tab Utility

Button Type Function

Otros manuales para R19IHAT-66EX

Tabla de contenidos

Otros manuales de Panel táctil de Winmate

Winmate

Winmate W04FA3S-EHT1 Manual de usuario

Winmate

Winmate E-Series Manual de usuario

Winmate

Winmate R19IB7T-GCM1 Manual de usuario

Winmate

Winmate G-WIN Slim IP65 Manual de usuario

Winmate

Winmate W05TA3S-PCT3AC Manual de usuario

Winmate

Winmate R15IK3S-SPC3 Manual de usuario

Winmate

Winmate W05TA3S-PCT3AC Manual de usuario

Winmate

Winmate R10IB3S-67T2 Instrucciones de funcionamiento y mantenimiento

Winmate

Winmate W07IB3S-PCM1AC Manual de usuario

Winmate

Winmate W22IK3S-SPA369 Manual de usuario

Winmate

Winmate G-WIN Manual de usuario

Winmate

Winmate R15FA3S-PCC3-PoE Manual de usuario

Winmate

Winmate R10L100-PCT2-PoE Manual de usuario

Winmate

Winmate W10IE3S-MRH2FP Manual de usuario

Winmate

Winmate R05FA3S-IPD1HMHB Manual de usuario

Winmate

Winmate W10IB3S-GSH1 Manual de usuario

Winmate

Winmate G-WIN AMD Rugged Series Manual de usuario

Winmate

Winmate R15IT3S-SPC369 Manual de usuario

Winmate

Winmate W07RK3S-PCO1-POE Manual de usuario

Winmate

Winmate W07FA3S-PCM1AC-PoE Manual de usuario

Winmate

Winmate W07IB3S-POT1 Manual de usuario

Winmate

Winmate W10IB3S-PCH2AC-PoE S-Series Manual de usuario

Winmate

Winmate R15IB3S-65EX Manual de usuario

Winmate

Winmate R15IK3S-SPC3 Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario