Winext AN-303 Manual de usuario
AN-303 Temperature Humidity Sensor
0
AN-303 Temperature Humidity Sensor
1
Content
1. Introduction ......................................................................................................................2
1.1 Description ...............................................................................................................2
1.2 Features ...................................................................................................................2
1.3 Specification.............................................................................................................2
2. Structure ..........................................................................................................................4
2.1 Appearance and dimension .....................................................................................4
2.2 Packing contents......................................................................................................4
3. How to work .....................................................................................................................5
3.1 Process ....................................................................................................................5
3.2 Use .........................................................................................................................6
4. Installation........................................................................................................................7
5. Configuration....................................................................................................................8
5.1 Tool list.....................................................................Error! Bookmark not defined.
5.2 Set up ......................................................................Error! Bookmark not defined.
5.2.1 Tools................................................................Error! Bookmark not defined.
5.2.2 Install wireless configuration module driver ...Error! Bookmark not defined.
5.2.3 Parameter configuration ................................................................................12
5.3 Remote configuration.............................................................................................15
6. Communication Format .................................................................................................17
7. Caution...........................................................................................................................18
AN-303 Temperature Humidity Sensor
2
1. Introduction
1.1 Description
AN-303 is a wireless temperature and humidity unit for data gathering and monitoring.
It has a built-in temperature and humidity chip. It has small body size and high
accuracy. With stable performance, low power consumption, it is suitable for data
transmission in long distance. Based on long battery life, free wiring installation,
AN-303 temperature and humidity sensor decreases the system cost greatly.
Application
Communication room, workshop line, drug warehouses, logistics warehouse,
agricultural greenhouses, archives, museums, hvac control and etc
1.2 Features
Support LoRaWANTM
Support Temperature and humidity detecting
Built-in 8500mAh battery
Wide humidity and temperature detection range
Support Temperature high and low threshold value setting
1.3 Specification
Function
Item
Description
Hardware parameter
Temperature detecting
range
-30℃~70℃
Temperature precision
±0.5℃
Humidity detecting
range
0~99.9%RH(non-condensing)
Humidity precision
±3%RH
Antenna
Built-in LoRa antenna
Wireless
performance
Tx rate
300bps-5.4Kbps
Protocol
Support LoRaWANTM and P2P
AN-303 Temperature Humidity Sensor
3
Function
Item
Description
Hardware parameter
Temperature detecting
range
-30℃~70℃
Temperature precision
±0.5℃
Humidity detecting
range
0~99.9%RH(non-condensing)
Humidity precision
±3%RH
Antenna
Built-in LoRa antenna
Frequency
CN470-510MHz
EU863-870MHz
US902-928MHz
AS923MHz
AU915-928MHz
KR920-923MHz
RU864-870MHz
IN865-867MHz
Max Tx power
17dBm
Rx sensitivity
-140dBm(SF=12)
Electric parameter
Power consumption
36mW
Battery capacity
3.6V/8000mA
Battery
Built-in Li-SOCL2 battery
VCC
DC 3.6V
Standby electric current
<=9uA
Tx current
<=125mA
Physical parameter
IP grade
IP30
Dimension
86mm*86mm*26mm
AN-303 Temperature Humidity Sensor
4
2. Structure
2.1 Appearance and dimension
Figure: AN-303
Figure: AN-303 Dimension(mm)
2.2 Packing contents
Accessory
Qty(pc)
AN-303 Temperature Humidity
sensor
1
Installation board
1
Screw and plastic rubber
2
User manual
1
AN-303 Temperature Humidity Sensor
5
3. How to work
3.1 Process
Figure: AN-303 Workflow
AN-303 Temperature Humidity Sensor
6
Figure: AN-303 Data Workflow
3.2 Use
Turn on: Press and hold the Turn on/off button at the back of the device for about
three seconds with the green light constant on until the buzzer gives out the sound.
Then the green light goes out. And the buzzer will stop automatically after three
beeps (di, di, di), indicating that the device is started.
Join network: When the device is turned on, the buzzer will sound "di" and "di",
indicating that the device is connected to the network.
Anti-dismantle button: After the device installation finished, the anti-dismantle
button is pushed against. When it detects the anti-dismantle button is released for
three seconds, the alarm will be reported and the red light will flash. When it
detects the tamper button is pushed against for three seconds, it will report
anti-dismantle status resume.
Turn off: Hold and press Turn on/off button for three seconds with the green
light on, until a long sound of buzzer sound heard and the green light is off.
Release the button, the device is off.
Note: It needs to wait for a while to reboot the device after it turned off.
AN-303 Temperature Humidity Sensor
7
4. Installation
Please prepare installation tools. Here are tools that may be used below.
Figure: Installation Tool
Quick Install
1. Put the back board at a proper position on the wall without tilting. Mark the
position and use percussion drill to make holes there.
2. Put the plastic cover in to the holes, align the back board in the holes on the wall,
use the taping screw to secure the back board.
3. Put AN-303 above the back board with AN-303 holder corresponding to back
board clasp. When they clasp together and pull AN-303 down.
Note: It can use gelatin sponge to adhere AN-303 on the surface where cannot drill
holes such as metal and glass wall. Put one side of gelatin sponge adhere to the
surface and put its other side to back board clasp. When AN-303 holder corresponding
to back board clasp get together and pull AN-303 down, a snap sound is heard. That
means installation is completed.
AN-303 Temperature Humidity Sensor
8
5. Configuration
5.1 Precaution
For device normal operation and detection accuracy, please pay attention to the
following matters before configuration:
Before configuration, please contact our technical staff for the relevant
software and manual.
For wireless configuration, it should be done within the signal coverage area
of the wireless configuration tool
5.2 Tool list
Note: For configuration, you can use wireless configuration tool (wireless
configuration) or USB to TTL cable (cable configuration), but here we choose to tell
customer how to do wireless configuration.
Item
Description
Laptop
Installation
Wireless Configuration tool
The laptop communicates with device via
wireless configuration tool ireless
configuration tool(wireless configuration),
you should install CP210x driver for this
tool
Configuration software
Winext manage App
5.3 Wireless configuration
5.3.1 Wireless configuration tool
Configuration tools as below:
AN-303 Temperature Humidity Sensor
9
a) Install the CP210x driver for wireless configuration tool, file as below:
b) Install Winext manage App, file as below:
5.3.2 Install CP210x driver for wireless configuration tool
(1) Open CP210x driver for wireless configuration tool
(2) Select the driver program to install depending to the system type.
32-bit operating system selects “CP210xVCPInstaller_x86.exe”.
64-bit operating system selects "cp210xvcpinstaller_x64.exe".
(3) Install Wireless configuration tool driver
Here we take an example to use the 64-bit operating system to install the wireless
configuration tool driver
Click and select Next to the driver file "cp210xvcpinstaller_x64.exe".
Tabla de contenidos
