Winegard TRAV’LER DISH 1000 Manual de usuario

Replacement DISH®1000

LNB Assembly

www.winegard.com/mobile

For Technical Services,

email [email protected] or call 1-800-788-4417

2452138

Rev6 3-17

Follow the steps below to raise the antenna for reflector, bracket, and LNB assembly

removal.

Pay attention to the pinch points as the antenna raises. See below.

Press [POWER], and hold for two seconds to turn on

the TRAV’LER®interface box. Wait until the interface

box finishes “connecting to antenna.” The TRAV’LER

antenna may enter the search routine after ten seconds.

As the antenna raises, press [POWER] and [SELECT] at the

same time. The antenna should stop moving.

Unplug the TRAV’LER interface. Continue with reflector

removal.

If you cannot get the antenna to raise by following the above instructions,

you may have to raise the antenna with the emergency manual stow drive.

Emergency manual stow is meant as a last resort!

Unplug the TRAV’LER interface, and remove the

plastic bolt from the back of the mount.

Insert a 3/8inch socket extension into

this auxiliary drive. Turn the auxiliary

drive counterclockwise to raise the

unit. Do not use a drill!

After raising the unit, continue with the

next section to remove the reflector

and LNB assembly.

Pinch Point

Top View Side View

Pinch Point

Plastic bolt

Raising the Antenna

If converting a DIRECTV SWM Slimline antenna to a DISH TRAV’LER antenna, remove

the power inserter and SWM splitter; these will not be used.

Remove the four reflector nuts and bolts, and remove the dish. Set the nuts and

bolts aside.

Disconnect the coaxial cables from the turret. Note that the D port will not be

present on a SWM TRAV’LER antenna.

Remove the bolt holding the cable harness to the unit, and detach the cable

harness from the lift arm.

Set the bolt aside; you will need this later.

NOTE If you are replacing an existing Reflector and Assembly, follow the instructions

below, otherwise proceed to “Installing the DISH Reflector and LNB Assembly” section.

Removing the Reflector and LNB Assembly

Reflector nut not shown

Turret

Bolt

Cable

clamp

Lift

Arm

Cable

harness

Remove the bolts holding the reflector bracket to the skew housing.

NOTE If replacing a Slimline assembly with a DISH

assembly, remove and set aside the stiffener

plate inside the reflector bracket.

Remove the LNB arm assembly, and set aside.

NOTE If replacing a Slimline assembly with a DISH assembly, remove the four bolts from the

adaptor plate, and remove the adaptor plate.

NOTE If replacing a Slimline assembly with a DISH assembly, align the small post on the back

of the DISH 1000 adaptor plate with the small groove on the skew assembly hub. Fit the

small post into the groove. Secure the adaptor plate to the hub with the four supplied ¼inch Allen screws.

Stiffener

plate

Skew housing

Reflector bracket

Bolts

Adaptor plate

Installing the DISH Reflector and LNB Assembly

Groove

Post

Align the four holes on the inside of the reflector bracket with the four marked

holes in the adaptor plate. See image below for the holes to align with the

reflector bracket and adaptor plate. The numbers on the reflector bracket and

adaptor plate should match.

TIP The bracket should be installed so that the LNB arm

assembly is at the bottom of this plate.

Replace the supplied 3/16 inch Allen screws through these

four holes, and tighten.

After the bracket has been installed, connect and tighten the

coaxial cables. These can be re-connected in any order, but

port D should be left open.

Install the provided F-cap on port D. The F-cap will not be

used if converting from a SWM TRAV’LER antenna.

Find the cable tie on the coax cables that you just connected to the mount.

Place the coax cable clamp on the cables just above this cable tie. Carefully

screw this coax cable to the lift arm using the 5/16 inch screw provided.

Be careful not to strip out the hole for the 5/16 inch screws when you replace

the clamp holding the coax cables to the arm. Do not use a power tool.

NOTE

If the cable tie is missing, install the clamp fourteen inches from the end

of the connectors.

Align the four outer holes in the reflector bracket with the four corresponding

holes in the reflector. Install a bolt through each hole on the front of the reflector,

and install a nut on each bolt. Tighten.

Use the provided packaging to re-package the removed LNB and attached cables.

If you are an RP-SK21 user, see Re-packaging the Removed LNB for RP-SK21 Users.

If you are an OE-DISH user, see Re-packaging the Removed LNB for OE-DISH Users.

F-cap

Press and hold [POWER] for two seconds or until the TRAV’LER interface displays

“POWER ON.”

Now that the power is on, release the [POWER] button.

Press and hold the [ENTER] button for two seconds. The TRAV’LER interface will

ask if you wish to enter the User Menu. Press [SELECT] to choose “Yes”; then,

press [ENTER].

The User Menu consists of four choices: Search Mode, Diagnostics, Installation,

and Exit. Press [SELECT] until the asterisk is next to “Installation” and then press

[ENTER].

The interface box will ask for a password. Press [ENTER] four times to enter code

“0000” on the display.

Press [ENTER] to choose “Select Antenna.”

Press [SELECT] until the asterisk is next to your mount type (SM Mount or LG

Mount), and then press [ENTER]. The mount type can be found on the sticker on

the TRAV’LER mount.

Selecting the incorrect mount type can result in damage to the unit or the RV.

Enter the four digit code for your mount type found on the sticker on the TRAV’LER

mount. Enter code 0022 for the SM mount or code 2112 for the LG mount. Press

[SELECT] to increase each number. Press [ENTER].

Press [SELECT] until the asterisk is next to DISH 1000. Press [ENTER].

Press [SELECT] until the asterisk is next to “Yes.” Press [ENTER].

The TRAV’LER interface box will display “in progress” and then “Success”.

Press [ENTER] and then choose [SELECT] until the asterisk is next to Installation.

Press [ENTER].

Setting the IDU for DISH 1000

If you had to raise the antenna with the emergency manual stow drive,

follow the instructions below for calibrating the elevation motor.

From the installation menu, press [SELECT] to move the asterisk to “Calibrate EL”;

then, press [ENTER].

Press [SELECT] to move the asterisk to “Yes.”

Press [ENTER] to start the elevation calibration procedure. The LCD should now

display “Calibrate EL In Progress.”

After a few moments, the TRAV’LER interface box will display “On EL Hard Stop?/

Yes *No.” Check that the antenna is against the hard stop.

TIP If the antenna is against the hard stop, the antenna will be pointing upward

as far as it can go.

Press [SELECT] to move the asterisk to “Yes” if the antenna is against its hard

stop.

Press [ENTER], and the LCD will display “Calibrate EL Success.” Press and hold

[POWER] for two seconds to stow the antenna.

Using the smaller cardboard box,

place two sheets of void fill in the

box so that they form an ‘X’.

Push the two sheets of void fill to the

bottom of the box.

Place the removed parts into the box with original packaging, and ship to Winegard

Company at 3111 Kirkwood St., Burlington, IA 52601.

Re-packaging the Removed LNB for RP-SK21 Users

NOTE Only the LNB and cables need to be returned to Winegard. Remove the LNB and cables

from the arm assembly, then follow the steps below.

NOTE If returning a replaced product to Winegard,

please follow the steps below.

Re-packaging the Removed LNB for OE-DISH Users

1 2

Return the package to 3111 Kirkwood St., Burlington, IA 52601. If a label has

not been provided, use Winegard’s UPS shipping account, 530400, to return the

package to Winegard Company.

Place another two sheets of void fill

in the cardboard box, and place the

LNB on top of these sheets of void fill.

Place two sheets of void fill in the

cardboard box, and push these two

sheets into the box so that they cover

the LNB.

Position the LNB in the center of the

box. Make sure the cables are still

connected to the LNB.

Place an additional two sheets of

void fill in the cardboard box so that

they form an ‘X’; close the box, and

tape it closed.

Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601

1-800-288-8094 • Fax 319-754-0787 • www.winegard.com • Printed in U.S.A.

Winegard and TRAV’LER are registered trademarks of Winegard Company.

DISH is a registered trademark of DISH Network L.L.C.

5 6

3 4

Tabla de contenidos

Otros manuales de Antena de Winegard

Winegard

Winegard Sensar HV Manual de usuario

Winegard

Winegard PR-7015 Manual de usuario

Winegard

Winegard MA1000W Manual de usuario

Winegard

Winegard PR-8800 Manual de usuario

Winegard

Winegard Pathway X1 Manual de usuario

Winegard

Winegard RM-DM00 Manual de usuario

Winegard

Winegard Carryout G2 Manual de usuario

Winegard

Winegard WPM-300 Manual de usuario

Winegard

Winegard GM-9000 Manual de usuario

Winegard

Winegard RZ-7500 Manual de usuario

Winegard

Winegard FlatWave Micro Manual de usuario

Winegard

Winegard YA-6260 Manual de usuario

Winegard

Winegard Movin' View MV3500T Manual de usuario

Winegard

Winegard sensar series Manual de usuario

Winegard

Winegard ROADSTAR RS-1000 Manual de usuario

Winegard

Winegard YA-1713 Manual de usuario

Winegard

Winegard YA-7000 Manual de usuario

Winegard

Winegard In-Motion MVT-35W Manual de usuario

Winegard

Winegard roadtrip T4 RT2000T Manual de usuario

Winegard

Winegard TRAV'LER SK-73UP Guía de inicio rápido

Winegard

Winegard Prostar 1000 PR-7010 Manual de usuario

Winegard

Winegard TR-6100 Manual de usuario

Winegard

Winegard AIR 360+ Manual de usuario

Winegard

Winegard SK-7003 Mount Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario