Winegard In-Motion MVT-35W Manual de usuario

In-Motion

Digital Satellite Mobile Antenna for Two Receivers

Models MV3500T (White Dome)

MV3535T (Black Dome)

WI3535T (Black Dome)

MVT-35W (White Dome, OEM)

MVT-35B (Black Dome, OEM)

INSTALLATION MANUAL

Made in the U.S.A. U.S. Patent Nos. 6,023,247; 6,188,300

Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000

319/754-0600 • FAX 319/754-0787 • www.winegard.com

Printed in U.S.A. © Winegard Company 2005 2452071 Rev.12/19/05

WINEGARD®

All required screws, washers, bolts, and nylocks

1 base with electronics, dish, dual LNBF

Silicone sealant

Surface Wipes

30’ Coax Cable

30’ Power Cable

1. Open box and remove packing material.

2. Lift dome out of box vertically. Then lift unit out of

box vertically. Do not turn box and “roll” out, or turn

upside down to remove.

USE 2 PEOPLE

when removing the unit

from the carton.

Parts Included • Tools Needed • How to Unpack

If using knife to open

carton, BE CAREFUL.

Do not cut the dome on

the unit.

1 Radome

1 Power switch

1 Wall plate (white)

1 Surface mount box

1 Cable entry plate

3 Base feet

large yellow flag connector

2 small red flag connectors

LIFT UNIT STRAIGHT UP

OUT OF CARTON!

TOOLS NEEDED FOR UNPACKING & INSTALLATION:

UNPACKING THE UNIT

Level

Drill w/3/4” bit

1-1/4” hole saw (if mounting switch in wall)

Phillips screw driver #2

3/8” Open end wrench

7/16” Open end wrench

Sealant (consult RV manufacturer for proper type

for your roof material)

PARTS INCLUDED:

!BE CAREFUL when

removing unit. Dome is

attached to base by

only 3 pieces of tape,

NOT BY SCREWS.

!DO NOT PAINT DOME!

Painting dome will

cause signal

degradation.



The Winegard MV3500T is designed specifically for use with motorized recreational

vehicles. Winegard recommends using a qualified installer familiar with RV structure and

wiring to ensure proper installation and to prevent damage to RV or dish.

REV. 12/05

Installation Diagram

Control Box detail

LNBF

RECEIVER

ELEVATION

AZIMUTH

(#1 represents Switch DOWN; #0 represents Switch up)

Sat. Rcvr. Switch Set Position

........................... 1 2 3 4 5 6 7 8

DISH NETWORK ................................ 0 .. 0 .. 0 .. 1 .. 0 .. 0 .. 1 .. 1

DIRECTV .................................. 0 .. 0 .. 0 .. 0 .. 0 .. 0 .. 0 .. 1

(FACTORY PRESET)

ExpressVu ................................. 0 .. 1 .. 0 .. 1 .. 1 .. 0 .. 1 .. 1

Model MV3500T

Control Unit

ELEVATION

MOTOR

AZIIMUTH

MOTOR

LNBF



REAR FOOT

MUST BE

PARALLEL

TO THE

CENTER LINE

OF THE

VEHICLE

AND FACE

THE REAR OF

VEHICLE

CENTER

LINE OF THE

VEHICLE



GPS CABLE

ELECTRONICS INTERIOR VIEW

GPS ANTENNA



 

2. Determine which programming you will be using. This will determine how you set your switches.

For DISH Network set switches to 119°. For ExpressVu®, set switches to 091°.

NOTICE!

This model is PRESET for DIRECTV®receivers.

If you have a DISH Network®or ExpressVu®(Canada) receiver,

you must change the numbered switches inside the dome.

TO CHANGE SWITCHES INSIDE DOME —

1. Remove screws holding dome to base and remove dome. Place dome in safe spot to avoid damage.

Switches will be set at 101° for DIRECTV®. You may be changing these switches.

(#1 represents Switch DOWN; #0 represents Switch up)

Sat. Rcvr. Mt. Option Switch Set Position

................................... 1 2 3 4 5 6 7 8

DIRECTV 0 0 0 0 0 0 0 1

(FACTORY PRESET)

DISH NETWORK 0 0 0 1 0 0 1 1

ExpressVu 0 1 0 1 1 0 1 1

Quick Reference Guide

1 2 3 4 5 6 7 8

SWITCH SETTINGS

SHOWN BELOW

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

1= DOWN 0= UP 1= DOWN

0= UP 1= DOWN

  

 



0= UP

1 = DOWN

0 = UP

  

0 0 0 0 0 0 0 1

0 0 0 1 0 0 110 10 1 10 11

DirecTV® receivers must be set to the two satellite, oval dish setting. Refer to your receiver manual.

DISH Network receivers must either have the check switch set for SW42 or unknown, no satellite found. See

page 5 in Operation Manual.

The satellite system has two modes of operation; Tracking Mode and Sleep Mode. When you first turn the unit

on, it enters Tracking Mode. In this mode the unit will search and actively follow the satellite as the vehicle trav-

els. Tracking mode ends when the unit has successfully finished its search and the vehicle has not moved for

six minutes.

Sleep Mode, this is the unit at rest mode. During Sleep mode the dish will toggle between primary and second-

ary satellites as you change channels with the remote. The unit enters Sleep mode about six minutes after a

successful search if stationary, or six minutes after the vehicle stops moving.

CENTER LINE OF VEHICLE

REAR BASE FOOT

(MUST BE PARALLEL

TO CENTER LINE)

MV-3500

BACK OF VEHICLE

FRONT OF VEHICLE

MV3500T

MOUNTING

!Rear foot MUST be

mounted towards BACK of

vehicle and PARALLEL to

center line. Failure to do

so may cause unexpected

operation!

IMPORTANT! Do not install this system

in the rain, or under any wet conditions. Mois-

ture may affect electronics and void your

warranty!

1. For best performance and to reduce signal ac-

quisition time, park vehicle on a level surface;

level the RV.

2. Select a level spot on your roof for installation.

Using the chart,

determine the

minimum distances

to other equipment.

WARNING: Level the base front to back and side

to side. If base is not level the MV3500T may re-

quire more time to locate the correct satellite

or may not locate the correct satellite.

• Be sure no roof-mounted equipment is

blocking the satellite “line of sight”, Fig. 3

• You will need to decide where the wires will enter

the vehicle. A coax and a power wire (minimum 16

gauge) will need to be run into the vehicle.

WARNING: Many +12VDC sources can cause the

unit to fail. Select a filtered source, preferably a dedi-

cated line to the battery.

Installation

Install in DRY conditions only!

Installing unit on roof of vehicle —

Obstruction Ht. Unit Clearance

8” .......................................... 4”

10” ................................... 11.5”

12” ...................................... 19”

15” ...................................... 32”

FIGURE 3

OBSTRUCTION

UNIT BASE

3. Remove dome. Place dome in safe spot to avoid

damage. Place base on vehicle roof in the location

selected.

4. Attach each mounting foot to base by securing

with two 7/16” nylocks.

5. After selecting location for unit (see number 2),

put the unit on the centerline of the vehicle.

REAR MOUNTING FOOT MUST BE PARALLEL

WITH THE CENTER LINE OF VEHICLE. See pg. 4.

FIGURE 4

8. Clean roof area where the base feet will be

attached to the roof. Do not erase your marks!

9. Put approved sealant in the areas marked

for the base feet. Place base feet on top of the

sealant and screw down with the (4) #10

screws (provided) for each foot.

10. After all base feet are secured to roof, put

sealant around edge of feet and over screws.

Replace base on screws and reinstall nut.

FIGURE 5 BASE EXTERIOR

FOOT

7. Place the unit on the roof in its permanent loca-

tion and mark around each base foot, Figure 4.

(Make sure the rear base foot is PARALLEL to

the center line of the coach and FACING to-

wards BACK of vehicle!) See pg. 2.

Installation

CABLE-

ENTRY

CABLE

CLAMPS

1. Decide the best location for the cables to enter

the vehicle, and the location of the power switch

and receiver (see “Installing the switch and

receiver”on pages 9 and 10). Drill a 1/2” hole in the

roof, push wires inside. Make proper connections.

You must have filtered +12 VDC power source.

2. Place cable-entry plate over hole and cables.

Screw in place. Seal plate and screw holes with ap-

proved sealant (not included).

3. Depending on the length of the cable on the roof,

you may need to use cable clamps or wire ties (not

provided) between the unit and your cable-entry plate.

Clamping the cable every 12”-16” should eliminate

any unnecessary cable movement, Figure 6.

FIGURE 6

Cable entry installation —

INSTALLING THE POWER SWITCH

1. Choose a location to install the MV3500T power

ON/OFF switch. Remember when selecting a location

that you will need to run the +12VDC power cable

from the MV3500T to the switch. Be sure the

switch is in the OFF position before continuing.

See Figure 7 page 9.

Wall or panel mount: Drill 1-1/4” hole, pull wires

through wall or panel.

Surface mount: Determine location and direction of

box. Mount box and feed wire into one of the box open

ings. Snap the rocker switch into the switch plate. Be

sure switch is off!

2. Connect the ground wire from the vehicle and the

BLACK ground wire from the MV3500T together,

using large yellow flag connector.

3. Connect the YELLOW flag connector to

the silver spade on the switch.

4. Connect the RED wire from the MV unit to the

small RED flag connector.

5. Connect small RED flag connector to center

spade on switch.

6. Connect the +12 V power wire from the vehicle to

a small RED flag connector.

7. Connect small RED flag connect to isolated

spade on switch.

INSTALLING THE POWER SWITCH DIAGRAM

STEPS 2 & 3

TWO GROUND WIRES

1 FROM VEHICLE

1 BLACK WIRE FROM

SATELLITE DISH STEPS 4 & 5

RED POWER

WIRE FROM

DISH

STEPS 6 &7

+12 V FROM VEHICLE

ON/OFF ROCKER SWITCH

WITH LIGHT

(Shown in OFF position.)

FIGURE 7

INSTALLING THE DOME

Insert screw in holes on dome

rim. Be sure bolt is vertical;

not tilted to side. Tighten to

20 in.-lb., or approximately

until washer is visible

around screw head.

CAUTION:

DO NOT

OVERTIGHTEN!!

10. The GPS antenna is pre-wired and has a 1 meter

cable running through one of the connectors.

Determine location for GPS antenna. It is recom-

mended you place the GPS antenna 3 feet from

dome and away from any other obstruction.

The recommended location for the GPS antenna is

based on having a level location and a clear view of

the sky for the best satellite signal acquisition. Do not

secure GPS antenna to roof at this time.

IMPORTANT! The GPS must be located minimum of

3 feet away from obstructions on roof of vehicle. An-

tenna must have a clear view of the sky for proper

operation.

GPS installation —

!BEFORE INSTALLING THE DOME, verify that

switches are set to your satellite provider.

(See page 2.)

QUADREX

SCREW WITH

RUBBER

WASHER

(USE #2

PHILLIPS)

!NICKS OR CUTS IN WIRING JACKET MAY

CAUSE WATER TO LEAK INTO VEHICLE.

REV. 12/05

1. Be sure vehicle is in a location free of all obstruc-

tions and with a clear view of the southern sky.

2. DO NOT MOVE VEHICLE during the first initial-

ization. Power up unit, turn on receiver. FOR THE

FIRST TIME ONLY, the unit may take up to 10 min-

utes to initially find the satellite signal. The GPS is

also initalizing at this time. After the GPS initializes,

the unit will begin searching for the correct satellite.

3. If the GPS does not initialize at this time, turn

off the unit. You may need to move the GPS an-

tenna to a different location on your roof. After you

move the GPS, DO NOT SECURE TO ROOF.

4. TEST YOUR SYSTEM BEFORE SECURING

THE GPS ANTENNA. Make sure the TV/receiver

has found the correct satellite.

5. After the correct satellite has been found, secure

GPS antenna by removing adhesive backing and

securing to roof.

Initializing & replacing the dome after

connecting the receiver(s) —

Connecting two receivers

1. Connect the coax cable coming from the

MV3500T to the “ SATELLITE IN” input on the

primary receiver. The primary receiver is the

receiver used most often and will toggle between

satellites.

2. Run a second cable through the empty Heyco

opening and connect to the ground block-type

feed through and connect the other end of this

cable to “Satellite IN” input on the second re-

ceiver. NOTE: Secondary receiver will not

toggle.

3. See page 5 of Operations Manual for receiver

set-up.

Installation • Wiring

Connecting one receiver

1. Connect the coax cable from the MV3500T to

the “SATELLITE IN” on the receiver.

2. See page 5 of Operations Manual for receiver

set-up.

Connecting the receiver —

CONNECTOR

APPLY SILICONE BEAD IN HOLE

WHERE COAX ENTERS

APPLY SILICONE BEAD

AT BASE OF CONNECTOR

UNIT BASE

PRIMARY

RECEIVER

USED ONLY WITH

A SECONDARY

RECEIVER

GROUND BLOCK

CUSTOMER/INSTALLER

PROVIDES COAX FOR

SECOND RECEIVER

To toggle between satellites when subscribing to multi-satellite programming—

The MV3500T will toggle between the primary and

seconday satellites for either DISH Network or

DIRECTV. Both have programming on more than

one satelite. When a channel is selected on the

remote control and is not on the satellite cur-

rently selected, the unit will automatically toggle

to the correct satellite.

DIRECTV programming

1. DIRECTV receivers must be set for oval dish 2

sat selection to enable toggling between primary

101°W satellite and alternate 119°W satellite

only. (Consult receiver manual for procedure.)

After receiver is set for the correct dish selection,

when you request a channel located on a differ-

ent satellite, the unit will automatically toggle to

that satellite.

DISH Network programming (DISH 500)

DISH Network receivers must have the “SW42”

switch installed in order to toggle between the pri-

mary 119° satellite and the alternate 110° satellite.

(Consult your receiver manual for the procedure to

reach the “check switch” menu.)

To install the “SW42” switch:

1. Before turning on your MV3500T system, make

sure that your satellite receiver and television are

turned on and your receiver is on the “point dish”

menu. (Consult your owner’s manual to reach this

menu.)

2. While the vehicle is stationary, turn on the

MV3500T system and wait for signal acquisition

on satellite 119°.

3. After signal is acquired, the system will

continously track the signal for approximately six

minutes. At the end of six minutes, the unit will

enter sleep mode. You now have six minutes to

complete Check Switch test. Consult your re-

ceiver manual for instructions on running the test.

Be sure that Superdish and Alternate are un-

checked if applicable. Onscreen options may vary

by receiver.

4. During the Check Switch Test, the receiver will

begin checking the switch by toggling between

satellites. When this is completed, SW42 will ap-

pear on the screen. It will be at the top of the

screen, satellite designations will be below, show-

ing odd and even transponders. See illustration.

NOTE: Be sure the “Superdish” and “Alternate”

boxes ARE NOT checked.

!Toggle: Your Winegard automatic

satellite dish will move from the

primary to the alternate satellite in

order to receive multi-satellite

programming.

If a switch other than SW42 appears, or you

have an X in one of the boxes below the satel-

lites, repeat Check Switch Steps.

5. Your system is now set up to toggle between

satellites. It will automatically move to the correct

satellite when a channel is selected with your re-

mote control.

NOTE: Once these steps are completed, you

won’t have to perform this test again, unless

Check Switch was performed on another satel-

lite dish, such as a home dish.

Check Switch screen display

Install Summary

Input: 1 1 1 1

Satellite: 119 119 110 110

Polarity: Odd Even Odd Even

Status: Satellite reception verified

Superdish Alternate

Cancel Test Help

SW42

Troubleshooting

The MV3500T does not attempt to find a satellite or

it never moves.

The dish never stops on any of the signals that

it sees.

1. Check your Power switch to verify that it is in the ON position.

2. Check +12 V wires at unit to verify power. Check fuse on electronics.

PROBLEM SOLUTION

1. Make sure that your receiver is set up correctly.

For DISH Network, the check switch should read either “Un-

known” or “SW42”.

For DirecTV the receiver should be set for a Two Satellite Oval

Dish.

With DIRECTV, the dish will find the alternate

satellite but it never finds the primary satellite.

I am not getting all the DISH Network channels

I subscribed to.

The MV3500T never sees any signals, it just keeps

searching.

Make sure that the Switches on the Electronics Control Box are

set for DirecTV. See page 3. These switches are found under

the dome, inside the Electronics Control Box.

1. Go to the check switch menu in receiver. Make sure that it’s

set for SW42 and lists both even and odd transponders on satel-

lites 110° and 119°.

1. Rain, Snow or excessive Dew on the dome can interrupt the

signal. Snow and Dew can be brushed off the dome. If Heavy

rain or Snow fall is blocking the signal, it may be necessary to

wait until the weather clears.

2. Check to see if the Southern sky is clear. Trees, Buildings, Large

signs or an Overpass can block the signal. Find an area where you

can be sure that this is not the problem and try again.

3. Make sure the receiver has power and the satellite dish is

connected to the “Sat In”.

I have switched satellite service providers. How do

I set my dish for my new provider?

You will need to remove the dome, and set switches to correct

provider. See page 4.

Features and specifications

• One button operation.

• Dual receiver capable.

• Depending on receiver type, you can access

satellites 119°, 110°, 101° or 92°.

• No user input required.

• No data port required for DISH Network®,

DIRECTV®or ExpressVu.

• Elevation range 20° to 74.5°;

azimuth +360° (0-720°)

• 30’ power cable and 30’ coaxial cable included.

• Dome UV protected.

• Compact size —

32” diameter, 15-3/4” height

Weight of unit - 28 lbs.

Shipping weight - 41 lbs.

• Specifications for max amperage 3.0A

• Specifications for unit operatating voltage.-10.5 - 13.8V

• Specifications for supply voltage. 12 - 13.8V

Winegard supplies 30’ of 16 AWG wire for connecting the

unit. When making connections or adding wire, Winegard

recommends using 16 AWG stranded wire or larger for

connection up to 60 feet. When making connections

longer than 60 feet, insure that specifications for unit oper-

ating voltage are met by measuring voltage at the unit.

• Operating temperature

-13°F to +140°F

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Antena de Winegard

Winegard

Winegard TR-6100 Manual de usuario

Winegard

Winegard WV750 Manual de usuario

Winegard

Winegard GM-9000 Manual de usuario

Winegard

Winegard Rayzar Z1 RZ-5000 Manual de usuario

Winegard

Winegard WPM-300 Manual de usuario

Winegard

Winegard Prostar 1000 PR-7010 Manual de usuario

Winegard

Winegard Movin' View MV-1111 Manual de usuario

Winegard

Winegard WAVU W1 Manual de usuario

Winegard

Winegard HD-6000 Manual de usuario

Winegard

Winegard HD7080P Manual de usuario

Winegard

Winegard SENSAR III ANTENNA Manual de usuario

Winegard

Winegard TRAV'LER SHAW DIRECT SK-7003 Manual de usuario

Winegard

Winegard HD7000R Manual de usuario

Winegard

Winegard Movin' View MV3500A Manual de usuario

Winegard

Winegard AIR 360+ Manual de usuario

Winegard

Winegard Movin' View MV3535A Manual de usuario

Winegard

Winegard RoadTrip Mission Manual de usuario

Winegard

Winegard AIR 360+ Manual de usuario

Winegard

Winegard DS-4248 Manual de usuario

Winegard

Winegard HD-6010 Manual de usuario

Winegard

Winegard Pathway X2 Guía de instalación

Winegard

Winegard Sensar HV CC-10HV Manual de usuario

Winegard

Winegard HD7210P Manual de usuario

Winegard

Winegard RAYZAR z1 Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario