Wine Guardian CS025 Manual de instrucciones
Wine Guardian®
Ceiling System Wine Cellar
Cooling Units
Models: CS025, CS050 (60Hz)
WGC60 (50 Hz)
Quick Start Installaon Guide
USA + 1 315-452-7400 | Europe + 41 52 224 0490
Part # 15H0270-00 Rev A 04/2021
wineguardian.com
2
Wine Guardian Ceiling System
This document is a pictorial guide for installing the Wine Guardian
Ceiling system. It is not intended to replace the detailed instructions
found in the Installation, Operation and Maintenance (IOM) manual,
which includes important safety messages all installers and owners
should follow for safe and optimal performance of the system.
Complete IOM manuals can be found on the Resources and Manuals
page of wineguardian.com. If you have additional questions related to
your Wine Guardian Ceiling System, please contact our authorized Wine
Guardian distributor or your local Wine Guardian office.
Please fill out the WG Split System start-up checklist that can be
found by downloading the full Installation, Operation, and
Maintenance manual from our website, for your model split
system.
English ............................................ page 3
Deutsch............................................ Seite 8
Español ...................................... página 14
Français .........................................page 20
中文 ....................................................页 26
Pусский .................................. cтраница 32
Product overview & Options ............page 38
....................................................................
3
1. Unpackage
A. Remove unit from box. Check for any signs of
concealed damage, and that all optional equipment
has been provided. Contact Air Innovations
immediately if components are missing or/if unit has
been damaged in shipping.
B. Shipment includes:
- One (1) Fan-coil unit
- One (1) Mounting flange
- One (1) Supply/Return Grille Assembly
- One (1) Condensing unit
- One (1) remote interface controller with 50’ control
cable
- One (1) Documentation Bag with auxiliary data plate
Humidification — Stand-alone
Ideal for adding humidity to your wine cellar.
Temperature / Humidity Remote Sensors
Sense and control multiple locations (maximum
of three) within your room. Ideal for odd shaped
rooms or multi-room applications.
4
2. Installing the Fan-Coil
Decide where the unit will be mounted, consider the
supply/return orientation, to ensure the utilities can be
connected to the correct side of the unit. The Ceiling
System consists of a Fan-coil Chassis, a Mounting
Flange, and a Diffuser (Fig. 1). The fan coil unit can be
located either above, or below the condensing unit in
height. Keep any height difference to a maximum of
15’ (4.57meters).
Mounting The Fan-Coil
A. Cut an opening in the ceiling 41” long x 14.5” wide
16” on center joists, or 41” long x 10.5” wide for a
12” on center joist spacing (Fig. 2).
B. Install the mounting flange onto the ceiling and
secure it to the joists using 2 1/2” flat head wood
construction screws (not provided). Ensure the hinge
area of the mounting flange is opposite the utility
connection side of the unit (Fig. 3).
C. Connect the fan-coil to the hinge of the mounting
flange (Fig. 4), swing the unit up and connect the fan
-coil to the mounting flange using four (4) washers,
lock washers, and nuts (Provided) (Fig. 5).
D. Connect all the utilities to the fan-coil. See the
complete Manual for instructions on how to
implement the provided Swage Locks (Page 35).
ATTENTION
E. After all utilities are connected, fill in any voids or
holes around unit including utility connection area
with insulation.
F. Attach the diffuser to the mounting bracket using the
hinges on the diffuser and flange and lock the
diffuser into place using the mounting clips (Fig. 6).
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
5
4. Condensate Drain
A. Wine Guardian ceiling systems come equipped
with a condensate pump system. Connect the
drain line to the barbed fitting at the unit and run
the drain line to the nearest drain location.
3. Installing Thermostat (Wired)
A. Unit is supplied with 50 feet (15 meters) of cable
with RJ-9 type connection to the Remote User
Interface Controller.
B. Disconnect wire from back of controller and route
the cable to the desired mounting location within
the room.
C. Locate Remote User Interface within the room
midpoint on a wall in an area with good airflow
and away from any windows or heat sources.
D. Remove back plate of controller and mark
mounting points at desired location.
E. Drill two 1/8” (3 mm) holes and insert anchors
within mounting surface. Anchors may not be
required if securing to wall studs or racking.
Insert screws into the anchors and test fit the
installation of the backing plate tighten/loosen
screws to create a snug fit.
F. Provide 3/4” (19 mm) diameter hole within wall or
racking structure to provide clearance for RJ-9
connection at the back of the controller.
G. Re-attach front cover plate by screwing it into
place on the back plate.
H. Connect RJ-9 cable to the back of the remote
user interface and attach to the wall at the screw
locations
I. Reconnect cable to side of Wine Guardian unit at
either COM1 or COM2.
Note: For wireless installations or multiple
remote interfaces, refer to the full version manual
located at wineguardian.com/manuals
6
MODEL LIQUID LINE (OD) SUCTION LINE (OD)
CS025
CS050 / WGC60
1/4 inch
1/4 inch / 0.635 cm
3/8 inch
1/2 inch / 1.27 cm
5. Installing the Condensing Unit
A. Wine Guardian condensing unit must be mounted
horizontally on its base as shown and be level to
+/- ¼” end to end and 1/8” side to side.
B. A minimum of 12 inches is required around the
perimeter of the condensing unit for proper
airflow across the unit and for service access.
C. Provide a one-inch pitch in suction and liquid line toward the evaporator
for every 10 feet of run to prevent any refrigerant that condenses in the
suction line from flowing to the compressor or when the unit is off.
D. Mount system on concrete slab outside above average snow fall heights.
Unit can also be mounted to side of house or within a large indoor crawl
space, attic, or mechanical room that is at least three (3) times the size of
the cellar.
E. Prevent dips, sags, or other low spots that will trap refrigerant oil.
F. Evacuate and leak test indoor unit suction and liquid lines by purging the
dry air charge from the unit by opening the liquid line shut-off valve or
removing the liquid line outlet fitting or plug, whichever is applicable for
your unit.
G. Pressurize and leak test system (the condensing unit comes pre charged).
A pressure equal to the low side test pressure marked on the unit
nameplate is recommended for leak testing.
H. Evacuate the system to hold at 500 microns and break the vacuum with
refrigerant. Charge the system with the correct amount of refrigerant and
mark the amount, with a permanent marker in the space provided on the
unit nameplate. (See chart on below)
I. See the full Wine Guardian Operations and installation manual for
comprehensive charging procedure. At www.wineguardian.com. Includes
charts for system Pressures, Superheat, and Sub-cooling.
7
7. Turn Unit On
A. Turn on power to the Fan-coil. Press the “On/Off” button on the Remote
User Interface. The Remote User Interface is preset to a room
temperature of 55°F (13°C).
B. Press the “Up” arrow once. The display will show the existing
temperature setpoint. Press the “up or down” arrow buttons to adjust the
temperature to the desired setpoint.
C. The system will turn on after a 5-minute time delay and the cold air
section will start to deliver cold air. Contact Air Innovations if the system
fails to turn on.
6. Wiring the Unit for Power
A. Connect line power to the contactor inside the
condensing unit as shown.
B. Run 24 volt low voltage signal wires from Y and C
terminals on fan coil to Y and C connections in
condenser housing (shown in image to the left).
C. Turn on power to the condensing unit 24 hours prior to
system start-up to allow crankcase heater to warm up
compressor.
*See page 20 in owners manual for full wiring
schematic. Inside of condensing unit also contains
schematic.
System Charging
Note: Each DS & WGS Model condensing unit is shipped with 16oz/.453kg
of refrigerant charge already, to be taken into account for below total
amounts based on 25’/7.62 meters interconnect length.
Here are the recommended factory total system refrigerant charges by model
based on the 25’/7.62meter interconnect baseline:
DS025= 62oz / 1.75kg (includes added charge required if an XLA system)
DS050=70oz / 1.98kg (includes added charge required if an XLA system)
WGS75=1.92kg (includes added charge required if an XLA system)
**For each 1 foot, or 1 meter more or less than 25 feet / 7.62 meters pip-
ing, adjust total system refrigerant R134A charge from above baseline
by .50 oz / .0465 kg”
8
Deutsch
Deckensystems von Wine Guardian
Dieses Dokument ist eine bildliche Anleitung für die Montage
des Deckensystems von Wine Guardian. Diese Anleitung soll
nicht die detaillierten Anweisungen des Installations-, Be-
dienungs- und Wartungshandbuchs (IBW) ersetzen, das
wichtige Sicherheitsinformationen enthält, die alle Installateure
und Besitzer für einen sicheren und optimalen Betrieb des Sys-
tems beachten sollten.
Vollständige IBW-Handbücher finden Sie auf der Seite
Ressourcen und Handbücher von wineguardian.com. Wenn
Sie weitere Fragen zu Ihrem Wine Guardian Deckensystem
haben, kontaktieren Sie bitte Ihren autorisierten Wine Guardi-
an-Vertriebspartner oder Ihr lokales Wine Guardian-Büro.
Bitte füllen Sie die Checkliste zur Inbetriebnahme für das WG
Split-System aus, die Sie beim Herunterladendes vollständigen
Installations-, Betriebs- und Wartungshandbuch für unser Modell-
Split-System auf unserer Website finden
9
Befeuchtung — Stand-Alone
Ideal, um Ihrem Weinkeller Feuchtigkeit hinzuzufügen.
Temperatur-/Feuchtigkeitsaußensensoren
Erfassen und steuern Sie mehrere Standorte (maximal
drei)
in Ihren Räumlichkeiten. Ideal für ungewöhnlich
geformte Räume oder Multi-Raum-Anwendungen.
Feuchtigkeit hinzuzufügen.
1. Auspacken
A. Einheit aus der Verpackung entnehmen. Über-
prüfen Sie alle Anzeichen von verdeckten Schäden,
und ob alle optionalen Geräte zur Verfügung
gestellt wurden. Kontaktieren Sie Air Innovations
sofort, wenn Komponenten fehlen oder wenn das
Gerät beim Versand beschädigt wurde.
B. Lieferung enthält:
- Eine (1) Gebläsekonvektoreneinheit
- Ein (1) Montageflansch
- Eine (1) Vor- / Rücklaufgitterbaugruppe
- Eine (1) Kondensatoreinheit
- Ein (1) Remote-Schnittstellen-Controller mit 127-
cm- Steuerkabel
- Ein (1) Dokumentationstasche mit
Zusatzdatenschild
10
2. Montage des Gebläsekonvektors
Legen Sie fest, wo das Gerät montiert werden soll, und
achten Sie auf die Ausrichtung von Vor- und Rücklauf, um
sicherzustellen, dass die Versorgungsleitungen an der richti-
gen Seite des Geräts angeschlossen werden können. Das
Deckensystem besteht aus einem Gebläsekonvektor, einem
Montageflansch und einem Vor- / Rücklaufgitter (Abb. 1).
Die Gebläsekonvektoreneinheit kann entweder über oder
unter der Höhe der Kondensatoreinheit platziert werden. Der
Höhenunterschied sollte nicht mehr als 4,57 Meter (15“)
betragen.
Montage des Gebläsekonvektors
A. Schneiden Sie eine Öffnung in die Decke, 104,1 cm
lang x 36,8 cm breit, für 40,6 cm Abstand zwischen den
Mittelträgern, oder 104,1 cm lang x 26,7 cm breit, für
30,5 cm Abstand zwischen den Mittelträgern (Abb. 2).
B. Bringen Sie den Montageflansch an der Decke an und
befestigen Sie ihn mit 2 1/2”-Holzschrauben (nicht im
Lieferumfang enthalten ) an den Trägern. Stellen Sie
sicher, dass der Scharnierbereich des Mon-
tageflansches gegenüber der Netzanschlussseite des
Geräts liegt (Abb. 3).
C. Verbinden Sie den Gebläsekonvektor mit dem
Scharnier des Montageflansches (Abb. 4), schwenken
Sie das Gerät nach oben und verbinden Sie den
Gebläsekonvektor mit vier (Abb. 4) Unterlegscheiben,
Sicherungsscheiben und Muttern (mitgeliefert) (Abb. 5).
D. Schließen Sie alle Netzteile an den Gebläsekonvektor
an. Anweisungen zum Anschließen der Swagelock-
Verschraubungen (Seite 35) finden Sie im vollständigen
Handbuch.
ATTENTION
E. Füllen Sie nach dem Anschließen aller Netzteile alle
Hohlräume oder Löcher um das Gerät einschließlich
des Netzanschlussbereichs mit Isolierung aus.
F. Befestigen Sie den Diffusor an der Montagehalterung,
indem Sie die Scharniere am Diffusor mit dem Flansch
verbinden und den Diffusor mit den Montageklammern
Abb. 1
Abb. 2
Abb. 3
Abb. 4
Abb. 5
Abb. 6
Otros manuales para CS025
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
Otros manuales de Enfriador de vino de Wine Guardian
Wine Guardian
Wine Guardian Sentinel Series Manual de usuario
Wine Guardian
Wine Guardian WG15 Documento técnico
Wine Guardian
Wine Guardian PRO Series Documento técnico
Wine Guardian
Wine Guardian 24S025 Manual de usuario
Wine Guardian
Wine Guardian Through-the-Wall Manual de instrucciones
Wine Guardian
Wine Guardian D050 Manual de usuario
Wine Guardian
Wine Guardian TTW018 Documento técnico
Wine Guardian
Wine Guardian DS050 Manual de instrucciones
Wine Guardian
Wine Guardian DS088 Manual de instrucciones
Wine Guardian
Wine Guardian WG 40 Documento técnico
Wine Guardian
Wine Guardian WGS25 Manual de instrucciones
Wine Guardian
Wine Guardian Through-the-Wall Manual de usuario
Wine Guardian
Wine Guardian WGC40 Manual de usuario
Wine Guardian
Wine Guardian DS025 Manual de instrucciones
Wine Guardian
Wine Guardian WG25 Documento técnico
Wine Guardian
Wine Guardian SS018 Manual de instrucciones
Wine Guardian
Wine Guardian WGS40 Documento técnico
Wine Guardian
Wine Guardian SP50 Manual de usuario
Wine Guardian
Wine Guardian SS018 Documento técnico
Wine Guardian
Wine Guardian Through-the-Wall Documento técnico
