WIN Enterprises MB-5000 Manual de usuario

MB5000

Embedded Micro SBC

User’s Manual

This publication contains information that is protected by copyright. No part of it may be re-

produced in any form or by any means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and specifi-

cally disclaims any express or implied warranties of merchantability or fitness for any particular

purpose. The user will assume the entire risk of the use or the results of the use of this docu-

ment. Further, the manufacturer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person or entity of such revisions

or changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

Table of Contents

Copyright...............................................................................................................2

Trademarks...........................................................................................................2

FCC and DOC Statement on Class B........................................................2

Warranty.................................................................................................................4

Static Electricity Precautions........................................................................4

Safety Measures.................................................................................................4

About the Package............................................................................................5

Optional Items.....................................................................................................5

Before Using the System Board..................................................................5

Chapter 1 - Introduction................................................................................6

Specifications.................................................................................................6

Features...........................................................................................................7

Chapter 2 - Hardware Installation.............................................................8

Board Layout................................................................................................ 8

System Memory .......................................................................................... 9

Block Diagram.............................................................................................. 9

Mechanical Drawing ................................................................................ 10

Rear Panel I/O Ports............................................................................... 11

2-Pin Terminal Block (DC 12V) ........................................................ 11

Graphics Interface .......................................................................... 12

RJ45 LAN Ports .............................................................................. 12

USB Ports ...................................................................................... 13

I/O Connectors.......................................................................................... 14

Digital I/O Connector...................................................................... 14

Expansion Slot ............................................................................... 14

COM (Serial) Port ........................................................................... 15

SMBus Connector ........................................................................... 16

Front Audio Connector.................................................................... 16

Battery .......................................................................................... 17

Chapter 3 - BIOS Setup..................................................................18

Overview....................................................................................................... 18

Insyde BIOS Setup Utility .................................................................... 19

Main .............................................................................................. 19

Advanced....................................................................................... 19

Security ......................................................................................... 26

Boot .............................................................................................. 26

Exit ............................................................................................... 27

Updating the BIOS .................................................................................. 28

Notice: BIOS SPI ROM .......................................................................... 28

Chapter 4 - Supported Software...............................................................29

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the product, in-

ability to use the product, unauthorized replacement or alteration of components and prod-

uct specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper instal-

lation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-

stances, attempt to perform service, adjustments or repairs on the product, whether in or

out of warranty. It must be returned to the purchase point, factory or authorized service

agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to the

product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in han-

dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are

ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contacts

or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con-

nectors by their ends.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for installation or servic-

ing. After installation or servicing, cover the system chassis before plugging the power

cord.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other com-

ponents. Perform the upgrade instruction procedures described at an ESD worksta-

tion only. If such a station is not available, you can provide some ESD protection by

wearing an antistatic wrist strap and attaching it to a metal part of the system chas-

sis. If a wrist strap is unavailable, establish and maintain contact with the system

chassis throughout any procedures requiring ESD protection.

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

• One MB5000 board

• One USB port cable (Length: 200mm)

• One COM port cable (Height: 300mm)

• One Heat spreader (Height: 11mm)

Optional Items

• Heat sink for E series CPU 0 to 60°C / wide temp (Height: 27mm)

• Heat sink for N series CPU 0 to 60°C (Height: 23mm)

• Power adapter (60W, 12V, DC jack) + 2 pole terminal to DC Jack cable

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the following

internal components.

• Storage devices such as hard disk drive, etc.

You will also need external system peripherals you intend to use which will normally include at

least a keyboard, a mouse and a video display monitor.

www.win-ent .com

Chapter 1 - Introduction

Speciﬁcations

Chapter 1

Chapter 1 Introduction www.winent.com

SYSTEM Processor Intel Atom®Processor E3900 Family, BGA 1296

Intel Atom®x5-E3940 Processor, Quad Core, 2M Cache, 1.6GHz (1.8GHz), 9.5W

Intel Atom®x5-E3930 Processor, Dual Core, 2M Cache, 1.3GHz (1.8GHz), 6.5W

Intel®Pentium®Processor N4200, Quad Core, 2M Cache, 1.1GHz (2.5GHz), 6W

Intel®Celeron®Processor N3350, Dual Core, 2M Cache, 1.1GHz (2.4GHz), 6W

Memory 2GB/4GB LPDDR4 Memory Down

Single Channel LPDDR4 2400MHz

BIOS Insyde SPI 128Mbit (supports UEFI boot only)

GRAPHICS Controller Intel®HD Graphics

Feature OpenGL 4.2, Direct X 11.1, OpenCL 1.2, OGL ES 3.0

HW Decode: H.264, MPEG2, VC1, VP8, H.265, MPEG4

HW Encode: H.264, MPEG2, MPEG4

Display 1 x Mini DP++

Mini DP++: resolution up to 4096x2160 @ 60Hz

EXPANSION Interface 1 x Full-size Mini PCIe (PCIe/USB 2.0, optional USB 3.1 Gen1/USB 2.0)

ETHERNET Controller 2 x Intel®I211AT PCIe (10/100/1000Mbps) or

2 x Intel®I210IT PCIe (10/100/1000Mbps)

REAR I/O Ethernet 2 x GbE (RJ-45)

USB 2 x USB 3.1 Gen1

Display 1 x Mini DP++

INTERNAL I/O Serial 1 x RS-232/422/485 (1.27mm pitch)

USB 1 x USB 2.0 (1.27mm pitch)

DIO 1 x 8-bit DIO

SMBus 1 x SMBus

STORAGE eMMC 1 x 16GB/32GB/64GB eMMC

WATCHDOG

TIMER

Output &

Interval

System Reset, Programmable via Software from 1 to 255 Seconds

SECURITY TPM fTPM 2.0

POWER Type Single 12V +/-10% DC

Connector 2-pin Terminal Block

Consumption Typical: E3940:12V @ 0.29A (3.48Watt)

Max.: E3940:12V @ 1.30A (15.6Watt)

RTC Battery CR2032 Coin Cell

OS SUPPORT

(UEFI ONLY)

Microsoft/

Linux

Windows 10 IoT Enterprise 64-bit

Ubuntu 16.04

ENVIRONMENT Temperature Operating: 0 to 60°C (Option: -20 to 70°C / -40 to 85 °C)

Storage: -40 to 85°C

Humidity Operating: 5 to 90% RH

Storage: 5 to 90% RH

MTBF 868,962 hrs @ 25°C; 638,889 hrs @ 45°C; 465,382 hrs @ 60°C

MECHANICAL Dimensions 1.8" SBC Form Factor

84mm (3.31") x 55mm (2.17")

Height PCB: 1.6mm

Top Side: 15mm, Bottom Side: 8mm

CERTIFICATIONS CE, FCC, RoHS

Chapter 1

Chapter 1 Introduction www.winent.com

Features

• Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the system at the set

time interval. If the system hangs or fails to function, it will reset at the set time interval so

that your system will continue to operate.

• LPDDR4

LPDDR4 SDRAM provides backward compatibility to LPDDR3 memory modules but can operate

at the same or at a lower power level.

• Graphics

The integrated Intel®HD graphics engine delivers an excellent blend of graphics performance

and features to meet business needs. It provides excellent video and 3D graphics with out-

standing graphics responsiveness. These enhancements deliver the performance and compat-

ibility needed for today’s and tomorrow’s business applications. Supports 1 x Mini DP++ inter-

face for display output.

• Gigabit LAN

Two Intel®I211AT PCI Express Gigabit Ethernet controllers or two optional Intel®I210IT PCI

Express Gigabit Ethernet controllers support up to 1Gbps data transmission.

• Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-on the system

manually or let the system power-on automatically.

• USB

The system board supports the USB 3.1 Gen1. It is capable of running at a maximum trans-

mission speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60

MB/s) and USB 1.1 (12Mb/s). USB 3.1 Gen1 reduces the time required for data transmission,

reduces power consumption, and is backward compatible with USB 2.0. It is a marked im-

provement in device transfer speeds between your computer and a wide range of simultane-

ously accessible external Plug and Play peripherals.

• Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is

supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Man-

agement Event) signal. However, if your system is in the Suspend mode, you can power-on

the system only through an IRQ or DMA interrupt.

• ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)

specification. ACPI has energy saving features that enable PCs to implement power manage-

ment and plug-and-play with operating systems that support power management features.

With ACPI, the system can further utilize the Ethernet adapter’s wake-on-LAN (WOL) capability

that enables remote wake-up if the Ethernet adapter supports such feature.

Chapter 1

www.winent.com

Chapter 2 Hardware Installation

Chapter 2

Chapter 2 - Hardware Installation

Board Layout

Top View Bottom View

Standby Power LED

LPDDR4LPDDR4

SPI Flash

BIOS

Mini PCIe

LAN 2

USB 0

USB 2.0

Battery

2-Pin Terminal Block

F81803

10 2

COM 1

LAN 1

USB 0-1

USB 3.1

Gen1

Mini DP++

eMMC

DIO

Intel Atom

E3900 Series

Intel I211AT or

optional I210IT

Intel I211AT or

optional I210IT

Front

Panel

1551

SMBus

LPDDR4LPDDR4

Buzzer

Chapter 2

www.winent.com

Chapter 2 Hardware Installationnhapter 2 Hardware Installation

Chapter 2

Block Diagram

Intel Atom

Processor

Super IO

with WDT

Digital I/O 8-bit

LPDDR4 2400MHz

Channel A

PCIe x1

(USB3.1 optional)

LPC Bus

SMBus

SPI

Full-size

Mini PCIe

USB 2.0

USB 3.1 Gen1/2.0 2x

USB 3.1 Gen1

USB 2.0

USB 1x

USB 2.0

RS-232/422/485 1x

I211AT

PCIe x1

GLAN 2

GLAN 1

I210IT (opt.)

Mini DP++

eMMC

System Memory

Important:

Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in

boards, and other components. Perform installation procedures at an ESD workstation

only. If such a station is not available, you can provide some ESD protection by wear-

ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If

a wrist strap is unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Important:

When the Standby Power LED lights red, it indicates that there is power on the sys-

tem board. Power-off the PC then unplug the power cord prior to installing any de-

vices. Failure to do so will cause severe damage to the motherboard and components.

• 2GB/4GB LPDDR4 Memory Down

• Single Channel LPDDR4 2400MHz

Features

LAN 1

LPDDR4

Standby Power LED

Chapter 2

www.winent.com

Chapter 2 Hardware Installation

Chapter 2

Mechanical Drawing

Chapter 2

Tabla de contenidos

Otros manuales de Computadora de placa única de WIN Enterprises

WIN Enterprises

WIN Enterprises MB-80510 Manual de usuario

WIN Enterprises

WIN Enterprises PL-80910 Manual de usuario

Manuales populares de Computadora de placa única de otras marcas

AXIOMTEK

AXIOMTEK SBC81206 Series Manual de usuario

Embest

Embest SOM-PH8800 Manual de usuario

SeaLevel

SeaLevel SBC-R9 Manual de usuario

SMART Embedded Computing

SMART Embedded Computing ATCA-8310 Manual de usuario

WinSystems

WinSystems PPM-LX800-G Manual de usuario

GIGAIPC

GIGAIPC QBiX-PPC Series Manual de usuario

OLIMEX

OLIMEX A10S-OLinuXino-MICRO Manual de usuario

Commell

Commell FS-978 Manual de usuario

GIGAIPC

GIGAIPC QBiP-8665A/ Manual de usuario

VersaLogic

VersaLogic Python EBX-11 Manual de usuario

Micro Computer Specialists

Micro Computer Specialists IRV-3702 Manual de usuario

CompuLab

CompuLab SB-A510 Manual de usuario

Boser

Boser HS-7321 Manual de usuario

Premier Farnell

Premier Farnell Embest SBC8530 Manual de usuario

MicroSys Electronics

MicroSys Electronics miriac SBC-LS1043A2 Manual de usuario

Aaeon

Aaeon UP Manual de usuario

Portwell

Portwell WUX Series Manual de usuario

Lanner electronics

Lanner electronics IAC-F847 Series Manual de usuario