Wildfire Effects Master EM-44V Manual de usuario

Operation Manual

Ultraviolet Fluorescent Lighting Fixtures

EM-44V

Table of Contents

Introduction 3

Safety Information 3

Specifications 4

Setup and Operation 5

Unpacking 5

Optional Accessories 5

Setup 5

Operation 5

Maintenance & Troubleshooting 6

Lamp Replacement 6

Cleaning 6

Troubleshooting 6

Diagrams 7

Isometric & Line Views 7

Exploded View & Part List 8

Schematic 9

Spectral Output Graph 10

Photometrics Chart 10

Limited Warranty 11

Introduction

Congratulations on your purchase of an Effects Master VHO Series fixture by Wildfire. This 4 lamp black light

powerhouse features proprietary VHO electronic ballasting and polished Everbrite reflectors for maximum state-

of-the-art performance. Each Effects Master VHO fixture is precision engineered to provide you with years of

trouble free service. Please take a moment to read this manual thoroughly before attempting to operate this

fixture. Improper set-up, use or servicing may cause damage to the fixture and/or lamps and void the fixture’s

warranty.

Safety Information

CAUTION – THIS FIXTURE IS TO BE OPERATED IN ACCORDANCE WITH THE WAY IT WAS DESIGNED

AND TESTED. OPERATE IN DRY INDOOR LOCATIONS ONLY. USE WITH MAX 60W T8, T10, T12 LAMPS

ONLY. SUITABLE FOR SURFACE MOUNTING ONLY.

Specifications

Housing:

16 Ga. Rolled steel with stainless steel hardware

Finish: Flat black powder coat

Mounting:

Two fully adjustable mounting brackets

Reflector:

Polished Everbright Aluminum 165°

Sockets:

Eight positive locking medium Bi Pin G13

Ballast:

Electronic VHO Power Factor > 70%

Rating:100, 120 or 240VAC / 50-60Hz / 5.5A max. / 300W

Circuit Protection:

One 7A Slow Blow Fuse

Operating Temperature:

50° F to 100° F

Power Cord:

6’ 16/3 SOW with PowerCON in and male Edison

Power Connections:

Neutrik PowerCON In and Out

Power Linking:

3 Units at 120VAC

Lamps:

Four Wildfire SableLux F32T8BLB Lamps (Not included)

Peak Spectra Output:

368nm With Wildfire SableLux Lamps Installed.

Lamp Life:

8,000 Hrs.

Weight:

17.60 lbs./7.98 kg.

Dimensions:

4.18”/10.62cm High x 4.90”/12.44cm Wide x 24”/60.96cm Long

Rating:IP-20 Indoor use

Standard Equipment:

Adjustable Mounting Brackets

Optional Accessories:

Twenty Clamp (147-021)

Safety Cable (147-002)

Floor Mount (147-006)

Specifications subject to change without notice

Made in the USA

Setup & Operation

Unpacking

Unpack the fixture and carefully inspect it for any signs of physical damage. Report any damage to Wildfire or

your local distributor immediately. Included with each unit should be the following items:

1. Two “L” shaped mounting brackets with one 1/2” mounting hole for mounting the fixture to a standard c-clamp

and two 3/8” mounting holes for mounting the fixture to Unistrut, optional Floor Mount Kit or any flat surface.

2. Two rubber friction washers that are to be placed between the mounting brackets and the end caps on either

end of the fixture allowing it to be held firmly in place upon tightening the locking knobs

3. Two locking knobs with ¼-20 threaded studs that screw into the end caps.

Optional Accessories:

Twenty Clamp – These clamps when attached to both of the fixtures adjustable mounting brackets allows you

to mount the fixture to a standard 2” pipe truss. Contact Wildfire or your local distributor for pricing.

Safety Cable- This cable is to be used when installing the fixture on a pipe truss with the Twenty Clamps. It

attaches to the metal ring on the rear of the fixture securing it from falling if the clamp is not tightened properly.

Contact Wildfire or your local distributor for pricing.

Floor Mount Kit- This aluminum stand set enables you to mount your fixture on the floor for footlight

applications. Contact Wildfire or your local distributor for pricing.

Setup

The first step is to install the lamps in the fixture. Refer to Lamp Replacement on page 5 for correct installation.

Connect the blue PowerCON connector on the power cord to the blue PowerCON AC Input receptacle on the

fixture. The fixture is also provided with a gray PowerCON AC Output receptacle, enabling you to interconnect

power between fixtures. Do not interconnect more than three Effects Master VHO fixtures in a single

chain.

Plug the fixture into the appropriate properly grounded power source. If you are controlling the unit with a

lighting control board you will need to make sure it is plugged into a non-dim circuit. Do not at any time plug

the fixture into a dimmable circuit, doing so will damage the ballast in the fixture and void the warranty.

Operation

To turn the fixture on switch the rocker switch on the side of fixture to the ON position. Unplug the fixture from

the AC power outlet during prolonged periods of non-operation.

Maintenance & Troubleshooting

Lamp Replacement

Refer to Fixtures Specifications on page 4 for information on selecting the proper replacement lamp for your

fixture. Unplug the fixture. If this is not possible then steps should be taken that would allow the fixture to remain

in an off state while re-lamping. If the fixture has been On allow the lamps to cool for several minutes before

attempting to touch them as they will be very hot. Holding the lamp firmly with two hands, one hand near each

end of the lamp, rotate the lamp about its long center-line axis, one quarter (1/4) turn either clockwise or

counter-clockwise. The sockets will click and the lamp will become loose. Gently pull the lamp free of the

sockets. Install the new lamp by lining up the two pins on the ends of the lamp so that they will slide into the

open slot in the socket. Gently push the lamp into the sockets and turn the lamp one-quarter (1/4) turn either

clockwise or counter-clockwise, until the lamp socket makes a small click or you feel a detent position. Gently

pull on the lamp to make sure that both ends of the lamp are installed correctly, neither end of the lamp should

move in the socket.

Cleaning

For best performance, the reflector and lamps should be kept free of dirt and dust. At no time should any

cleaning chemicals or abrasives be used to clean any part of the unit. For normal cleaning, a dry soft cloth

should be used to wipe any surface free from dust and light dirt. Cleaning the reflector will require that the

lamps be removed. Remove lamps by following the instructions listed under Lamp Replacement above. Always

unplug the unit before cleaning. Once the lamps have been removed, gently wipe off the reflector using a soft

dry cloth. In the event the reflector is heavily soiled, lightly dampen the cloth with a mild window cleaning agent

and wipe. Lamps should be cleaned using the same method; first use a dry soft cloth and then proceed with a

window-cleaning agent if lamp is too heavily soiled. Do not spray or apply any liquid directly to any part of the

fixture.

Troubleshooting

Other than the lamps, there are no user serviceable parts in the fixture.

Isometric & Line Views

Diagrams

4.25”

6.5”

51.37”

48.25”

Exploded View & Part List

PART NAMEPART#QTY.#PART NAMEPART #QTY.#

104-066-0511 Housing Effects Master VHO

104-060-0322 Cover Housing Side VHO

121-00583 Screw, M, PHL, PH, 6-32 x 1/4” 18-8 SS

126-002-0314 Reflector 4’ Fluorescent, VHO

104-003-0325 Bracket, Mounting

121-05126 Washer, Neoprene, 1.5”OD .25”ID .2” THK BK

120-00227 Knob, Bracket Adjustment

107-00318 Cord, Power, Black, 16 AWG, 8’

108-00489 Socket, Lamp G13 Base

121-0171610 Screw, SM, PHL, PH, #8 x 3/8”, 18-8 SS

141-002411 Lamp, SableLux Fluorescent, 4’

106-051112 Receptacle, PowerCON 1, Power-In NAC3MPA-1

106-053113 Receptacle, PowerCON 1, Power-Out NAC3MPB-1

110-007 to 010114 Ballast, (120V)(220V)(100V)(277V)

121-001415 Screw, M, PHL, PH, 4-40 x 1/4” 18-8 SS

121-056416 Washer, Flat, 5-16 OD

121-066417 Spacer, Nylon, 3/8” OD, #8 ID, .125” thk.

105-020118 Switch, DSPT, 15A, Effects Master Series RRA12C1100

106-050119 Connector, PowerCON 1, Power-In NAC3FCA

121-003420 Screw, M, PHL, PH, 4-40 x 3/8” 18-8 SS

121-034421 Nut, Nylock, 4-40, 18-8 SS

121-035122 Kepnut 6/32 18-8 SS

Schematic, EM-44V

BLACK

WHITE

GREEN

ELECTRONIC BALLAST

BROWN

PURPLE

RED

YELLOW

9 AMP FUSE

ORANGE

BLUE

POWER SWITCH

AC OUTPUT

AC INPUT

WHITE

GREEN

BLACK

Spectral Output Graph

UV-B UV-A VISIBLE LIGHT

WAVELENGTH /NM

100

300 350 400 450 500

RELATIVE ENERGY (%)

With Wildfire SableLux BLB Lamps

Photometrics Chart

Model EM-44V With SableLux Lamps

Distance in Feet /Meters

5/1.52

10 /3.05

20 /6.10

30/9.14

40/12.19

50/15.24

60/18.29

76.0

23.1

198.0

151.9

46.3

45.5

303.8

92.5

12.3

455.7

138.8

5.5

607.7

185.2

3.0

759.6

231.5

1.9

911.5

277.8

1.3

All peak UV-A irradiance measurements taken at beam center using UVX Digital Radiometer and a calibrated 365nm sensor

Beam Angle Feet

Beam Angle Meters

Peak UV-A Irradiance µW/cm

Tabla de contenidos

Otros manuales de Luminaria de Wildfire

Wildfire

Wildfire Long-Throw WF-402FF Manual de usuario

Wildfire

Wildfire Long-Throw WF-401F Manual de usuario

Wildfire

Wildfire EM-23S Manual de usuario

Wildfire

Wildfire LT-150 series Manual de usuario

Wildfire

Wildfire UltraBlade UB-44 Manual de usuario

Wildfire

Wildfire EffectsMaster EM-22L Manual de usuario

Wildfire

Wildfire LONG-THROW WF-252F1 Manual de usuario

Wildfire

Wildfire LT-400F1 Manual de usuario

Manuales populares de Luminaria de otras marcas

Emos

Emos CLASSIC ZY1431T Manual de usuario

Westinghouse

Westinghouse Outdoor Lighting Fixture Manual de usuario

Hedler

Hedler C 12 silent Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck: CSI Manual de usuario

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manual de usuario

Lightmaxx

Lightmaxx Shaft 5R Manual de usuario

Triarch

Triarch 31083 Manual de usuario

Philips

Philips 32614 Series Manual de usuario

IKEA

IKEA TIVED Manual de usuario

Lightolier

Lightolier LP200 Manual de usuario

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manual de usuario

Martin

Martin MAC 250 Krypton Manual de usuario

Cooper Lighting

Cooper Lighting Halo L3232E Manual de usuario

Stageline

Stageline ODW-2410RGBW Manual de usuario

Light Sky

Light Sky Tornado Series Manual de usuario

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario

Lightolier

Lightolier Lytespan 83ED17S Manual de usuario

Lightolier

Lightolier Calculite CS8226 Manual de usuario