WiCS MMC-2611TA Manual de usuario
MMC-2611TA
Paging Host User
Manual
Contents
Contents ..............................................................................................2
1. Summary.........................................................................................3
2. Appearance......................................................................................3
3. Parameter ........................................................................................4
4. Main Functions...............................................................................5
5. Software setup.................................................................................7
5.1 Function Introduction........................................................7
5.2 Edit Function ...................................................................13
5.2.1 Pager Registration.................................................13
5.2.2 Palm Registration ..............................................14
5.2.3 Call Button Registration.......................................15
5.2.4 Manual Send Data.................................................16
5.2.3 Data Download.....................................................17
6. Usage.............................................................................................18
7. Troubleshoots................................................................................20
8. FCC Important Note .....................................................................21
FCC Part 15.19 Warning Statement..........................................21
FCC Part 15.21 Warning Statement..........................................21
FCC Part 15.105(b) Warning Statement...................................22
1. Summary
MMC-2611TA works with all MMCall call buttons. It sends alphanumeric
message to pager MMC-NC-8E. The functions are: wireless alphanumeric message
paging, wireless deletion, duty repage, dispatch, urge dishes, monitoring function,
USB data download and program update etc. It is suitable for restaurants, hotels,
banks, bars etc.
2. Appearance
2.1 Front
Back
Power
Indicator
RX
Indicator
TX
Indicator Field Strength
Indicator
3. Parameter
3.1. Parameter
Category Parameter
Dimension 200mm * 173mm *37mm
Power supply 12V/ 1.5A
Communication mode
and interface type
USB（RJ45）
Outside Indicator Power supply,RX,TX
Configurable
transmitting frequencies
462.750MHZ, 462.775MHZ, 462.800MHZ,
462.825MHZ, 462.850MHZ, 462.875MHZ,
462.900MHZ, 462.925MHZ, 465.000MHZ
Receiving frequency 433.500MHZ
DC-12V
Power Cable
Interface
RX
Antenna
Paging No. in cache 40
Repage No. in cache 20
Transmitting power 100mW
Sensibility -106dB
Antenna Outside BNC Socket
Capacity Call button——200
Pager ——20
Palm transmitter——9
Message length 48 digits or letters
Signaling standard POCSAG，numeric, english and chinese
message supported
Temperature -30℃— +65℃
Table 3.1 Paging host parameter list
4. Main Functions
Main functions are as following：
1. Wireless receiving function. The host can receive the signals from call button
and palm transmitter with feature code, and transmit the message to corresponding
pager.
2. The pager has to be MMC-NC-8E, which can display numeric and english
message.
3. Text preprogrammed function. The paging unit, such as, table, room, bed etc.
and the paging category such as call, bill, water can be preprogrammed to the host and
related with corresponding call button. When the button is pressed, the pager will
display a complete message, such as Table No.5 calls for service.
4. Repage function. Repage times and interval can be setup between the waiter
and his directors. If repaging is not finished yet while you cancel it, the message
already sent will be automatically deleted.
5. Palm transmitter can be used for dispatching or urging dishes function.
6. Software sending message function. With computer software, the
preprogrammed message can be edited to page the programmed pager for interior
staff management.
7. Monitoring function. Connected directly with the computer through USB
interface, it can monitor the messages from call buttons and palm transmitters for
evaluating staff’working efficiency.
If the installation position of the host can not be connected with the computer, the
monitor box can be used for the monitoring function.
8. USB data download and upload , program update function available.
5. Software setup
Before using the paging host, please first setup the host parameter, pager, call
button and palm transmitter. Use the CA software to edit and download the
information. The software communication with the paging host is USB mode.
Notes: While using, USB can not power on the host, so please connect it with
power supply. Otherwise the transmitting and receiving function can not be used.
5.1 Function Introduction
The software interface as picture 5.1 shows, mainly includes pager
list, palm transmitter list, call button list and manual send data. In the
setup column, there are file, system setup, read data, download data.
Picture 5.1 TA Software Interface
1、File
As picture 5.2 shows, it’s mainly the database operation, including
New file, Open, Save as, Delete and Exit.
Notes: There should be a database while using the software. For the
first time use, it’s necessary to setup a new database, you can choose TA
or CA database. The two kinds of database are not compatible with each
other.
Picture 5.2 File
2. System Setup
System setup including initialization, host parameter, program update,
call type registration and pager check time.
Picture 5.3 System Setup
（1）Initialization
It will initialize all the host parameters.
（2）Host Parameter
Host parameter as picture 5.4, room No. Switch is temporarily
invalid, the monitor function needs to work with monitoring software, it
can be setup as transmitting data, USB passback, net page
passback(customization required), among which transmitting data
monitor needs to setup pager receiver No., other modes do not need to
setup the No.
Repage setup, it can setup the pager and its director repage times and
interval.
Transmission mode, there are two modes: inner transmission mode
and 485 output, this is valid only for CA. For TA, only inner transmission
mode.
Picture5.4 Host Parameter Setup
（3）Pager check time
It can check the pagers’time.
Notes: you need to setup group ID, the default ID is 0.
（4）Call Type
As picture shows, call button type setup, is to edit the multi-key
buttons while registering them. Under this option, the call type can be
edited and after one key call, the software will automatically show the
preprogrammed type. E.g. The key quantity of E3 button is 3 key, and the
key value 1,3,5 is chosen, after you press the call button, the host will
automatically list the message key 1,3,5.
3 Read Data
Read those already programmed or downloaded data. If no
download, then data read is empty.
Tabla de contenidos
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
