Whispbar K335W Manual de usuario
K335W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 4 x 4
x 4
Revision No: 3C 1
Fitting Kit K335W
MAX kgs (lbs)
W/P WHD
Holden
Commodore VT/VX/VY/VZ, 5dr Wagon Sep 97-Jun 08 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Commodore VT/VX/VY/VZ, 5dr Wagon Sep 97-Mar 08 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K335W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
3
Fitting Kit EN
K335W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the rear of this manual for
information relating specifically to your
vehicle.
4
Fitting Kit EN
K335W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
5
Fitting Kit EN
K335W
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Slide hex nuts into vehicle tracks. Two per
track.
●Repeat for both tracks.
●Use tape measure to ensure spacing is
equal.
●Assemble as shown.
6
Fitting Kit EN
K335W
●Carefully select position on vehicle roof
making sure that your crossbar lengths will
match selected positions for the tracks.
●Using the bolts with plastic knobs, attach
crossbars to the nuts by fitting the bolt
through the internal block on the foot and
screwing it into the nut.
●Tighten the plastic knob.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
7
Fitting Kit EN
K335W
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
8
Fitting Kit EN
K335W
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
9
Fitting Kit EN
K335W
●Check and replace worn out or defective
parts.
●Keep the product clean and maintained.
●Never drive into a car wash with the roof
rack system fitted.
●Lubricate locks and adjusting screws at
regular intervals.
●Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
●Yakima Australia Pty Ltd
17 Hinkler Court
Brendale QLD 4500
AUSTRALIA
www.whispbar.com
www.whispbar.com.au
www.whispbar.co.nz
www.whispbar.co.uk
www.whispbar.co.za
www.whispbar.eu
www.whispbar.ca
10
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Whispbar
Whispbar
Whispbar K673W Manual de usuario
Whispbar
Whispbar K885W Manual de operación e instalación
Whispbar
Whispbar K428W Manual de usuario
Whispbar
Whispbar K539W Manual de usuario
Whispbar
Whispbar K378W Manual de usuario
Whispbar
Whispbar K832W Manual de usuario
Whispbar
Whispbar K462W Manual de usuario
Whispbar
Whispbar K451W Manual de usuario
Whispbar
Whispbar K847W Manual de usuario
Whispbar
Whispbar K619W Manual de operación e instalación
Whispbar
Whispbar K365W Manual de usuario
Whispbar
Whispbar K174W Manual de operación e instalación
Whispbar
Whispbar K355W Manual de usuario
Whispbar
Whispbar K501 Manual de operación e instalación
Whispbar
Whispbar K901W Manual de usuario
Whispbar
Whispbar K604W Manual de usuario
Whispbar
Whispbar K822W Manual de usuario
Whispbar
Whispbar K582W Manual de usuario
Whispbar
Whispbar K753W Fitting Kit Manual de usuario
Whispbar
Whispbar K554W Manual de usuario
