Whirlpool AC1888 Manual de usuario
AC0788
AC0988
AC1288
AC1888
AE0789
AE0989
AC0788N
AC1888N
AC0988N
AE0789N
AC1288N
AE0989N
AE1889 AE1889N
AE1289 AE1289N
Thank you for choosing Whirlpool air conditioner. Our design is based on the best efficiency and the lowest noise operation and itcan
keep the room comfortable. Please read this operating manual carefully before operating the unit and keep it for consultation.
CONTENTS 1
2
3
5
6
6
7
10
13
14
15
16
17
Function
Operating condition
Installation
Notes for installation
Part identification
Air direction adjustment
Air conditioner opperation
Operation tips
Caution
Care and maintenance
Trouble shooting guide
After service
Structure mechanism
and Installation
Operation procedureCare and maintenance
Remote control operation procedure
Function and working temperature range.
Introduction
Window type room air conditioners of Whirlpool can regulate the room temperature,dry
the room. It is convenient for your work,study and life. It can be widely used in residence,
shop, hotel, office, library and laboratory, and so on.
Cooling in summer
In hot summer, Air conditioner can cool down
room air by transferring heat out.
Without reducing room temp, air conditioner
can dehumidify and make room air dry and
comfortable.
Dehumidifying in rainy or
humid season
1
Operating Condition
COOL mode operation
Outdoor temperature should be in range of 21
to 52 , otherwise it is possible for air conditioner
to breakdown.
Room humidity should be lower than 90% .
Otherwise, it is possible for air conditioner to dew
at air conditioner surface and even drop water after
running for so much time. But this maybe normal.
Please operate air conditioner in the correct conditions as following.
DRY mode operation
Outdoor temperature should be in range of 21
otherwise it is possible for air conditioner to breakdown.
Power requirement
Water pipe
The ground must be connected.
Special socket must be used. Furthermore, the socket and wiring
must conform to the wiring regulations. And the earthing method
must be reliable.
In fixed circuit, there must be electricity leakage protection switch
of enough power capacity and air switch with enough space.
Earth wireTo ensure the reliable earthing, please do not connect earth wire to the following places:
to 52 ,
2
How to install:
Choose a location where there are no any obstacle surrounding
the unit.
Prepare the installation hole slightly bigger than unit size.
Choose the installation space according to the following diagram.
The distance of obstructions from window unit inside should be
upper 300mm, lower 1500mm, left 500mm, right 500mm,
front1500mm.
3
Horizontal line
Sunshade board
Wall
Wooden frame
Rubber plate
Support
Horizontal line
Drain water:
To get the maximum cooling efficiency, the air conditioner is designed to splash the condensation water on the
condenser coil.
If the splashing sound annoys you, you can provide an outside drain by using the following procedure, which
may however cause a small loss of performance.
1. Slide out the chassis from the cabinet.
2. Remove the rubber plug from the body base plate.
3. Install the drain pan to the corner of the cabinet with 2 screws.
4. Connect the drain hose to the outlet on the drain pan bottom.
5. Slide the chassis into its original place in the cabinet.
Installation procedure:
1) Remove the sticker from the front panel.
2) Put the unit into the installation hole.
When installing the unit, it should be slanted
down to the back to avoid the enlargement of
noise or vibration. (Slant between 6-10mm.)
(Shown at right figure.)
The installation place should be strong enough
to avoid the enlargement of noise or vibration.
3) Fill up sews in the cabinet with sponge or foam.
Installation assistance:
Use iron support
The installation hole should be strong enough to
support the air conditioner. If it cannot, iron sup-
port has to be used outdoors.
Iron support should be fixed on the building (Shown
at right figure.)
Use sunshade board
Air conditioner should avoid anything to be dropped
into it and avoid direct sunshine. If there is no cover
on it, you should contact the seller for installing
the sunshade board. When installing the sunshade
board, don’t let it block the air inlet at the side grille.
4
Notes for installation
Remove
Before removing air conditioner to the other place, you should
contact the seller firstly.
Then it must be done under the direction of the professional
technician. In addition, the charge of this must be paid.
Noise
Electric wiring
Install in a location where is firm enough to avoid the enlargement of noise
and vibration.
Don’t put anything in front of the outlet of outdoor unit to avoid increasing
noise.
Be sure that hot air ornoise will not inconvenience neighbors.
Please contact the seller as soon as there is strange noise during operation.
Please use the safety support.
Must connect with ground reliably.
The exclusive circuit must be used. But removable socket can’t be used because poor
contact of it can cause over heat or fire.
Don’t pull the power cord strongly.
In fixed circuit, there must be electricity leakage protection switch and leakage current
is less than 30mA.
Air switch (thermal-magnetic breaker) should be installed in the circuit and its capacityis
10A for 7K and 9K, 15A for 12K, 20A for 18K, .
The fixed wiring should be more than
4.0mm
2
in area.
Note:
Drain hose or tubing can be purchased locally to satisfy your particular needs.
An all-pole disconnection switch having a contact separation of at least 3mm in all poles
should be connected in fixed wiring
Connecting method between air conditioners and power cord and interconnecting method
of each individual element with one another should accord with wiring diagram on the unit.
The air conditioner should be installed in accordance with national wiring regulation.
5
PART IDENTIFICATION
Air filter
(behind the front intake grille)
Front intake grille Control panel cover Power cord
Front grille
Air inlet louver
Cabinet
Vertical airflow direction vane
(Airflow direction adjustment up and down).
The vertical airflow direction vane is controlled by
positioning the vane to discharge the air upwards,
downwards or straight out.
Air direction adjustment
Panel outlook picture, just for reference, please take the real unit as standard.
6
3 MINUTES WAITBEFORE RESTARTING
Mechanical only
AIR CONDITIONER OPERATION
7
8
Este manual sirve para los siguientes modelos
15
Tabla de contenidos
Otros manuales de Acondicionador de aire de Whirlpool
Whirlpool
Whirlpool ACM102XF0 Manual de usuario
Whirlpool
Whirlpool WHAW050BW Manual de usuario
Whirlpool
Whirlpool ROOM AIR CONDITIONER Manual de usuario
Whirlpool
Whirlpool AR1230XA0 Manual de usuario
Whirlpool
Whirlpool ACQ102PV Manual de usuario
Whirlpool
Whirlpool YACQ088XP0 Manual de usuario
Whirlpool
Whirlpool WHHW182AW Manual de usuario
Whirlpool
Whirlpool ACM052PS0 Manual de usuario
Whirlpool
Whirlpool ACP102PR2 Manual de usuario
Whirlpool
Whirlpool ACQ082XK1 Manual de usuario
Whirlpool
Whirlpool 1159801 Manual de usuario
Whirlpool
Whirlpool ACP102PR0 Manual de usuario
Whirlpool
Whirlpool 1172397 Manual de usuario
Whirlpool
Whirlpool PORTABLE AIR CONDITIONER Manual de usuario
Whirlpool
Whirlpool 819052203 Instrucciones de montaje
Whirlpool
Whirlpool R1011 Hoja de información del producto
Whirlpool
Whirlpool COOLERATOR AR0600XV0 Manual de usuario
Whirlpool
Whirlpool AR0500XA Manual de usuario
Whirlpool
Whirlpool AMD 011 Manual de usuario
Whirlpool
Whirlpool SPIW409A2WF Manual de usuario
