Whelen Engineering Company IS1 Series Manual de usuario

ENGINEERING COMPANY, INC IS1 SERIES

MICRO SIZE

STROBE BEACONS

IS1224P, 12-48 VDC, PIPE MOUNT

IS1120P, 120 VAC, PIPE MOUNT

IS1224S, 12-48 VDC, SURFACE MOUNT

IS1120S, 120 VAC, SURFACE MOUNT

IS124CP, 12-48 VDC, CAST, PIPE MOUNT

Doc No. 04-0113085-01

Route 145, Winthrop Road

Chester, CT06412-0684

TELEPHONE: (860) 526-9504

TOLL FREE: 1-800-637-4736

1996 Whelen Engineering Company, Inc. Doc No. 04-0113085-01

May 24, 1996. 13085B

BASE

O RING SEAL

PCB ASSEMBLY

STROBE TUBE ASSEMBLY

#6-32 SCREW

CLAMP RING

DOME

STOP NUT

WARNING ALWAYS

DISCONNECT POWER

BEFORE SERVICING OR

INSTALLING AN IS1

SERIES BEACON.

SEE OTHER SIDE OF PAGE FOR

REPLACEMENT PARTS LISTING.

DESCRIPTION QTY. PART NUMBER

STROBE TUBE ASSEMBLY 1 01-0441319-00

DOME, AMBER 1 68-2130024-10

DOME, BLUE 1 68-2130024-20

DOME, CLEAR 1 68-2130024-30

DOME, GREEN 1 68-2130024-40

DOME, RED 1 68-2130024-50

O RING SEAL, PLASTIC BASE 1 38-0416442-00

GASKET, CAST BASE 1 38-0230104-00

MOUNTING INSTRUCTIONS

The IS1 Series Beacons are made for permanent

surface mount or pipe mount on a 1/2” NPT thread.

SURFACE MOUNT, PLASTIC BASE

1. Locate the wires in the wire slot and mount with

two screws. Make sure that the wires are in the wire

slot and not pinched under the Base.

PIPE MOUNT (Internal Thread)

1. Feed the power wires through the pipe.

2. Wire according to the WIRING instructions.

3. Screw the base onto the 1/2” NPT pipe and hand

tighten.

WIRING INSTRUCTIONS

MODELS IS1224P and IS1224S

MODEL IS124CP

1. Connect the RED wire to the positive DC

voltage (+).

2. Connect the BLACK wire to DC ground (-).

MODELS IS1120P and IS1120S

1. Connect the BLACK wire to the AC hot wire.

2. Connect the WHITE wire to the AC return wire.

Refer to the IS1 Series Product Sheet for current

draw to determine the proper wire gauge.

STROBE TUBE REPLACEMENT

1. Turn off power and wait 10 minutes.

2. Loosen the clamp ring screw and remove the

dome. Save the O Ring.

3. Press the tabs together on the Strobe Tube

Assembly and firmly pull the assembly out of the

PCB assembly. Do not pull the PCB Assembly away

from the Base.

4. Snap the replacement Strobe Tube Assembly into

the PCB Assembly. Roll the O Ring down the Base,

to get it in position. Position the Dome and secure

the clamp ring.

IS1 SERIES REPLACEMENT PARTS LISTING

3.4"

3.8" 2.5" DIA

1996 Whelen Engineering Company, Inc. Doc No. 04-0113085-01

May 24, 1996.

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de seguridad de Whelen Engineering Company

Whelen Engineering Company

Whelen Engineering Company SS361 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company 1010 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company 295SLSA5 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company IPS 400 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company 3012 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company RB6 Series Manual de usuario

Whelen Engineering Company

Whelen Engineering Company ECE ROTA-BEAM R416E Manual de usuario

Whelen Engineering Company

Whelen Engineering Company Super-LED L31HBF Series Manual de usuario

Whelen Engineering Company

Whelen Engineering Company L21 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company ECE 360 Class 1 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company SSNF360 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company WS2100 Series Manual de usuario

Whelen Engineering Company

Whelen Engineering Company L21HAM Manual de usuario

Whelen Engineering Company

Whelen Engineering Company WS295HFS1 Series Instrucciones de instalación

Whelen Engineering Company

Whelen Engineering Company L21LAM Manual de usuario

Whelen Engineering Company

Whelen Engineering Company RB6T Manual de usuario

Whelen Engineering Company

Whelen Engineering Company 295HFSA5 Manual de usuario

Whelen Engineering Company

Whelen Engineering Company 2015 Series Manual de usuario

Whelen Engineering Company

Whelen Engineering Company 295HFS5 Series Instrucciones de instalación

Whelen Engineering Company

Whelen Engineering Company Responder DX Series Manual de usuario

Whelen Engineering Company

Whelen Engineering Company Traffic Advisor TA837A Manual de usuario

Whelen Engineering Company

Whelen Engineering Company ISB Series Manual de usuario

Whelen Engineering Company

Whelen Engineering Company WPS-2900 Series Manual de usuario

Whelen Engineering Company

Whelen Engineering Company RB6PAPS Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario