Whadda WPI322 Manual de usuario

USER MANUAL

2.4 GHz NRF24L01 wireless transceiver module

WPI322

whadda.com

Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its

lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted

municipal waste; it should be taken to a specialized company for recycling. This device

should be returned to your distributor or to a local recycling service. Respect the local

environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Whadda! Please read the manual thoroughly before bringing this

device into service. If the device was damaged in transit, do not install or use it and contact

your dealer.

Safety Instructions

Read and understand this manual and all safety signs before using this appliance.

For indoor use only.

•This device can be used by children aged from 8 years and above, and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning the use of the device in a

safe way and understand the hazards involved. Children shall not play with the device.

Cleaning and user maintenance shall not be made by children without supervision.

General Guidelines

•Refer to the Velleman®Service and Quality Warranty on the last pages of this manual.

•All modifications of the device are forbidden for safety reasons. Damage caused by

user modifications to the device is not covered by the warranty.

•Only use the device for its intended purpose. Using the device in an unauthorized way

will void the warranty.

•Damage caused by disregard of certain guidelines in this manual is not covered by the

warranty and the dealer will not accept responsibility for any ensuing defects or

problems.

•Nor Velleman Group nv nor its dealers can be held responsible for any damage

(extraordinary, incidental or indirect) –of any nature (financial, physical…) arising from

the possession, use or failure of this product.

•Keep this manual for future reference.

What is Arduino®

Arduino®is an open-source prototyping platform based on easy-to-use hardware and

software. Arduino®boards are able to read inputs –light-on sensor, a finger on a button or a

Twitter message –and turn it into an output –activating of a motor, turning on an LED,

publishing something online. You can tell your board what to do by sending a set of

instructions to the microcontroller on the board. To do so, you use the Arduino

programming language (based on Wiring) and the Arduino®software IDE (based on

Processing). Additional shields/modules/components are required for reading a twitter

message or publishing online. Surf to www.arduino.cc for more information.

RED Declaration of Conformity

Hereby, Velleman Group nv declares that the radio equipment type WPI322 is in compliance

with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet

address: www.velleman.eu.

Product Overview

This module is based on Nordic®’s nRF24L01, a highly integrated, ultra-low power (ULP)

2 Mbps RF transceiver for the 2.4 GHz ISM (Industrial, Scientific and Medical) band. The

Nordic® nRF24L01+ integrates a complete 2.4 GHz RF transceiver, RF synthesizer, and

baseband logic including the Enhanced ShockBurst™hardware protocol accelerator

supporting a high-speed SPI interface for the application controller.

Specifications

•power supply: 1.9-3.6 V

•IO port working voltage: 0-3.3 V

•transmitting rate: +7 dB

•receiving sensitivity: < 90 dB

•transmission range: 250 m in open area

•dimensions: 15 x 29 mm

Features

•worldwide license-free 2.4 GHz ISM band operation

•250 kbps, 1 Mbps and 2 Mbps on-air data-rate options

•Enhanced ShockBurst™hardware protocol accelerator

•ultra-low power consumption - months to years of battery lifetime

Example

Connection

You will need two Arduino®boards and at least two RF modules, one to transmit and the

other to receive. If you use a standard Arduino®board, you should use the Arduino®board’s

3.3 V pin (VDD3V3) to provide power (the nRF24L01 module has 1.9-3.6 V power voltage

level). Please note: do not use 5 V pin (VDD5V) to provide power as this may destroy the

module.

RF module

Arduino® Uno compatible board

GND

VCC

3.3V

CSN

D10

SCK

D13

MOSI

D11

MISO

D12

Upload the included example program to both the transmitting and receiving Arduino®.

Make sure to install a jumper wire between analogue pin A4 and GND on the Arduino®board

that needs to act as the receiver.

Example

This is an example of how to use the RF24 library to control an LED wirelessly from

another Arduino® using two NRF24L01 modules.

Start by wiring up two Arduino®s with the NF24L01 according to the provided schematic.

Connect on one Arduino® a button to digital pin 2.

Connect on the other Arduino® an LED (through an appropriate current limiting resistor,

220 ohms is recommended), and a jumper between analog pin 4 and GND to select this

Arduino® as the receiver.

You can upload the same sketch to both Arduino®s. Once completed and running, the LED

on the receiving side should toggle on/off when pressing the button connected to the

transmitting Arduino®.

Example based on led_remote from nRF24 library

This program is free software; you can redistribute it and/or

modify it under the terms of the GNU General Public License

version 2 as published by the Free Software Foundation.

Modified by Midas Gossye (Velleman Group nv)

#include <SPI.h>

#include "nRF24L01.h"

#include "RF24.h"

#include "printf.h"

// Hardware configuration

// Set up nRF24L01 radio on SPI bus plus pins 9 & 10 (CE & CS)

RF24 radio(9,10);

// sets the role of this unit in hardware. Connect to GND to be the 'led' board receiver

// Leave open to be the 'remote' transmitter

const int role_pin = A4;

// Pin on the remote for button

const uint8_t button_pin = 2;

const uint8_t num_button_pins = sizeof(button_pin);

// Pin on the LED board

const uint8_t led_pin = 2;

const uint8_t num_led_pins = sizeof(led_pin);

// Topology

// Single radio pipe address for the 2 nodes to communicate.

const uint64_t pipe = 0xE8E8F0F0E1LL;

// Role management

// Set up role. This sketch uses the same software for all the nodes in this

// system. Doing so greatly simplifies testing. The hardware itself specifies

// which node it is.

// This is done through the role_pin

// The various roles supported by this sketch

typedef enum { role_remote = 1, role_led } role_e;

// The debug-friendly names of those roles

const char* role_friendly_name[] = { "invalid", "Remote", "LED Board"};

// The role of the current running sketch

role_e role;

// Payload

uint8_t button_state;

uint8_t led_state;

// Setup

void setup(void)

{

// Role

// set up the role pin

pinMode(role_pin, INPUT); // set role pin as input

digitalWrite(role_pin,HIGH); // enable internal pull-up role pin

delay(20); // slight delay just to get a solid reading on the role pin

// read the address pin, establish our role (transmitter or receiver)

if ( digitalRead(role_pin) )

role = role_remote;

else

role = role_led;

// Print preamble

Serial.begin(115200); // Begin serial communication for debugging

printf_begin();

printf("\n\rRF24/examples/led_remote/\n\r");

printf("ROLE: %s\n\r",role_friendly_name[role]);

// Setup and configure rf radio

radio.begin();

// Open pipes to other nodes for communication

// This simple sketch opens a single pipes for these two nodes to communicate

// back and forth. One listens on it, the other talks to it.

if ( role == role_remote )

{

radio.openWritingPipe(pipe);

}

else

{

radio.openReadingPipe(1,pipe);

}

// Start listening

if ( role == role_led )

radio.startListening();

// Dump the configuration of the rf unit for debugging

radio.printDetails();

// Set up button / LED

// Set pull-up resistor for button

pinMode(button_pin,INPUT);

digitalWrite(button_pin,HIGH);

// Turn LED ON until we start getting button responses

pinMode(led_pin,OUTPUT);

led_state = HIGH;

digitalWrite(led_pin,led_state);

}

// Loop

void loop(void)

{

// Remote role. If the state of any button has changed, send the whole state of

// all buttons.

if ( role == role_remote )

{

// Get the current state of buttons, and

// Test if the current state is different from the last state we sent

bool different = false;

uint8_t state = ! digitalRead(button_pin);

if ( state != button_state)

{

different = true;

button_state = state;

}

// Send the state of the buttons to the LED board

if ( different )

{

printf("Now sending...");

Serial.println(button_state);

// Send the payload, 1 byte, by passing address of button_state variable ( &button_state

indicates address of button_state variable)

bool ok = radio.write( &button_state, 1 );

if (ok)

printf("ok\n\r");

else

printf("failed\n\r");

}

// Try again in a short while

delay(20);

}

// LED role. Receive the state of all buttons, and reflect that in the LEDs

if ( role == role_led )

{

// if there is data ready

if ( radio.available() )

{

// Dump the payloads until we've gotten everything

while (radio.available())

{

// Fetch the payload, 1 byte, and put result in button_state variable ( &button_state

indicates address of button_state variable)

radio.read( &button_state, 1 ); //

// Spew it

printf("Got buttons\n\r");

Serial.println(button_state);

// For each button, if the button now on, then toggle the LED

if ( !button_state )

{

led_state ^= HIGH;

digitalWrite(led_pin,led_state);

}

Power on both Arduino®s. You can confirm if the RF modules are properly connected by

opening the serial monitor (set to 115200 baud) and checking the RX and TX addresses are

set to a non-zero value. Pressing the button connected to the transmitting Arduino®should

toggle on/off the LED connected to the receiving Arduino®.

For more info, please, consult

http://playground.arduino.cc/InterfacingWithHardware/Nrf24L01.

whadda.com

Velleman Group nv, Legen Heirweg 33 - 9890 Gavere.

Tabla de contenidos

Otros manuales de Unidad de control de Whadda

Whadda

Whadda WPSE353 Manual de usuario

Whadda

Whadda WPI425 Manual de usuario

Whadda

Whadda WPM402 Manual de usuario

Whadda

Whadda WPM307 Manual de usuario

Whadda

Whadda WPI430 Manual de usuario

Whadda

Whadda WPI317 Manual de usuario

Whadda

Whadda WPSE325 Manual de usuario

Whadda

Whadda DS1302 Manual de usuario

Whadda

Whadda WPM349 Manual de usuario

Whadda

Whadda WPM400 Manual de usuario

Whadda

Whadda WPI405 Manual de usuario

Whadda

Whadda Arduino 3.3 V Manual de usuario

Whadda

Whadda WPI302 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario