Western Digital WDXT-140 Manual de usuario
Installation Guide
Western Digital Corporation 1-1
Chapter 1
How To Install Your Hardware
Before you begin the actual installation of the WDXT- 140 or the
WDXT- 150 hardware and software, you need to prepare and install your
intelligent drives. Steps 1 and 2 below refer to these procedures.
Important
Each intelligent drive in your system requires a separate
interface cable. The WDXT-140 and the WDXT-150 DO NOT
support hard disk drives attached to daisy chain cables.
Installing Drive(s)
1. Turn your computer power switch OFF and unplug the power
cord. Then remove the computer cover. See manufacturer's
manual for details.
2. Look in your intelligent drive manual and follow the steps to
configure and to install your intelligent drive(s). These steps may
include:
•setting the drive number and terminator resistor
•attaching the cable(s) to each drive
•mounting the drive(s) into the computer case
•attaching your drive to a power source
Changing Adapter Jumper(s)
There are no jumpers on the WDXT-140. If you have a WDXT-
140 board, you can skip this section and go directly to the next section,
Connecting Cables.
The WDXT- 150 adapter board contains jumpers which control
the BIOS address, the port address, and the interrupt request. Figure 1-1
shows the location of these jumpers. Change the BIOS and port address
jumpers or the interrupt request on the WDXT-150 adapter board, if
necessary.
See Appendix B for instructions on how to change jumper
settings.
Installation Guide
Western Digital Corporation 1-2
Figure 1-1. WDXT-150 Jumper Locations
Connecting Cables
After you have completed installing your intelligent drive(s) and
changed any jumpers required on the WDXT-150 adapter board, follow
either step 1 (if you have the WDXT-140) or step 2 (if you have the
WDXT-l50) to connect your cables into your adapter board.
1. Connect cable(s) from drive unit(s) to WDXT-140 adapter board.
If you have a WDXT-140, see Figure 1-2.
If you have a WDXT-150, see Figure 1-3.
Drive 1 Cable Installation
Attach the interface cable 40 pin connector from the first drive to
J 1 on the adapter board. Attach Pin 1 of the cable connector to
Pin 1 on the adapter board. See Figure 1-2.
Pin 1 of the cable connector is marked and is on the color
coded edge of the cable. Pin 20 on the WDXT-140 board is
keyed (pin missing). Do NOT force the cables and connectors.
Installation Guide
Western Digital Corporation 1-3
Figure 1-2. Connect Pin 1 to Pin 1
Drive 2 Cable Installation
Attach the interface cable 40 pin connector from the second drive
to J2 on the adapter board. Attach Pin 1 to Pin 1. See Figure 1-2.
2. Connect cable(s) from drive unit to WDXT-150 adapter board.
Note: The WDXT-150 supports only one intelligent hard disk
drive.
Drive 1 Cable Installation
Attach the interface cable 40 pin connector from the drive to J2A
on the adapter board. Attach Pin 1 of the cable connector to Pin 1
on the adapter board. See Figure 1-3.
The WDXT-150 has a power connector, which can supply power
to the drive. This connector is located in the lower corner of the
board. See Figure 1-3. If you have no other way of connecting
power to your intelligent drive, then connect the drive power
cable to this connector.
Installation Guide
Western Digital Corporation 1-4
Figure 1-3. Connect Pin 1 to Pin 1
Pin 1 of the cable connector is marked and is on the color
coded edge of the cable. Pin 20 on the WDXT-150 board is
keyed (pin missing). Do NOT force the cables and connectors.
Inserting Adapter into Computer
After you have connected the cable(s) from either the WDXT-
140 or WDXT-150 to your intelligent drive(s), follow the steps below to
plug the board into your computer. Use an empty slot which is as close
to the intelligent drive(s) as possible, except as noted below.
Note: For IBM XT owners: DO NOT use the slot closest to the
power supply. Use an expansion slot at least one position
removed from the power supply.
1. Loosen the screw holding the plate cover for the selected
expansion slot. Remove the slot cover screw, but do not remove
the expansion slot coverplate.
Your adapter board should have a plastic clip attached. If the clip
is not attached to the board, locate the clip and gently push it onto
the upper right-hand corner of the adapter board. See Figure 1-4.
Installation Guide
Western Digital Corporation 1-5
Figure 1-4. Installing Clip
2. Hold the adapter board by the top corners and slide it into the
expansion slot. The board's edge connector (as shown in Figure
1-5) fits into the computer's motherboard expansion slot. Press
on the board as you insert it into the expansion slot. Check that
the board is seated properly by pressing down firmly on both ends
of the board.
3. After the board is seated firmly in the expansion slot socket,
secure the board using the plastic clip that is on the end of your
board. Place the screw over the clip and slot cover. Then screw
the clip and slot cover to the computer case.
Installation Guide
Western Digital Corporation 1-6
Figure 1-5. Installing WDXT-140 Board
Replacing Cover
1. Replace the computer cover. Make sure that cables are out of the
way and not caught between the cover and boards. Check that the
cables do not obstruct the air flow path from the fan or vents.
2. Plug the power cord back into your computer and turn the power
switch ON.
Your hardware installation is complete. However, you need to
format your hard disk and install an operating system and other software
before you can use your hard disk(s).
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Hardware de computadora de Western Digital
Western Digital
Western Digital WD Serial ATA RAID Controller Manual de usuario
Western Digital
Western Digital WD1003V-MM1 Manual de usuario
Western Digital
Western Digital WD1002-WAH Manual de usuario
Western Digital
Western Digital WD1006V-SR1 Manual de usuario
Western Digital
Western Digital WD1004A-27X Manual de usuario
Western Digital
Western Digital WD1003V-SR1 Manual de usuario
Western Digital
Western Digital WD1007A-WAH Manual de usuario
Western Digital
Western Digital WD Serial ATA RAID Controller Manual de usuario
Western Digital
Western Digital WDAT-140 Manual de usuario
Western Digital
Western Digital WD 1003-RA2 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
