Westermo Lynx DSS Manual de usuario

©Westermo Teleindustri AB

www.westermo.com

User Guide

6643-2230

Industrial Ethernet

5-port Device Server Switch

Lynx DSS

L105-S1/L205-S1

WeOS

6643-2230

Legal information

The contents of this document are provided “as is”. Except as required by applicable

law, no warranties of any kind, either express or implied, including, but not limited to,

the implied warranties of merchantability and fitness for a particular purpose, are made

in relation to the accuracy and reliability or contents of this document. Westermo

reserves the right to revise this document or withdraw it at any time without prior

notice.

Under no circumstances shall Westermo be responsible for any loss of data or income

or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

http://www.westermo.com

Software tools

Related software tools are available in the folder software tools under

technical support on the Westermo website.

6643-2230

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure

that you understand it fully. Check that your application does not exceed the safe

operating specifications for this unit.

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is

restricted to service personnel only. The power supply wiring must be sufficiently

fused, and if necessary it must be possible to disconnect manually from all

power supply. Ensure compliance to national installation regulations. This unit

uses convection cooling. Make sure that the unit is installed such as its ambient

temperature is within its specified maximum/minimum temperature.

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from all power supply.

WARNING

Do not open connected unit. Hazardous voltage may occur within this unit when

connected to power supply.

Before powering-up, a protective earthing conductor must be connected to the

protective earthing terminal and have a cross-sectional area of at least 1.5 mm².

Note that this unit can be connected to two different power sources.

When this unit is operated at an ambient temperature above +55°C (+131°F), the

External Surface of Equipment may exceed Touch Temperature Limit according to

EN/IEC/UL 60950-1.

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line

cord.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfill

the warranty obligations.

This unit must not be operating with removed covers or lids.

Do not attempt to disassemble the unit. There are not any user serviceable parts inside.

Do not drop, knock or shake the unit. Rough handling above the specification may cause

damage to internal circuit boards.

Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.

Do not expose the unit to any kind of liquids (rain, beverages, paint etc), unless all

connectors and the ventilation membrane are sufficiently protected.

Do not use or store the unit in dusty or dirty areas, unless all connectors and the

ventilation membrane are sufficiently protected.

Do not cover or bring mechanical force to the ventilation membrane on the back of the

unit.

If the unit is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo Tech support.

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

6643-2230

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 61000-6-3, Emission residential environments

EN 61000-6-4, Emission industrial environments

EN 50121-4, Railway signalling and telecommunications apparatus

IEC 62236-4, Railway signalling and telecommunications apparatus

Safety UL/IEC/EN 60950-1, IT equipment

Marine DNV GL rules for classification – Ships and offshore units .

FCC Part 15.105

Notice:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

… Reorient or relocate the receiving antenna

… Increase the separation between the equipment and receiver

… Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

… Consult the dealer or an experienced radio/TV technician for help.

Corrosive

environment

Notice:

This product has been successfully tested in a corrosion test according to

IEC 60068-2-60, method 3. This means that the product meets the requirements

to be placed in an environment classified as ISA-S71.04 class G3.

Note! If the product is placed in a corrosive environment, it is important that all

un-used connector sockets are protected with a suitable plug in order to avoid

corrosion attacks on the gold plated pins in connectors.

6643-2230

Declaration of Conformity

Westermo Teleindustri AB

Declaration of Conformity

Org.nr/

Postadress/Postal address

Tel.

Telefax

Postgiro

Bankgiro

Corp. identity number

Registered office

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

The manufacturer Westermo Teleindustri AB

SE-640 40 Stora Sundby, Sweden

Herewith declares that the product(s)

Type of product Model

Industrial Ethernet 5-port Device Server Switch Lynx DSS Lx05-S1y

is in conformity with the following EU directive(s).

No Short name

2014/30/EU Electromagnetic Compatibility (EMC)

2014/35/EU Low Voltage Directive (LVD)

2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic

equipment (RoHS)

References of standards applied for this EU declaration of conformity.

No Title Issue

EN 61000-6-1 Electromagnetic compatibility – Immunity for residential

environments

2007

EN 61000-6-2 Electromagnetic compatibility – Immunity for industrial

environments

2005

EN 61000-6-3 Electromagnetic compatibility – Emission for residential

environments

2007

+A1:2011

EN 61000-6-4 Electromagnetic compatibility – Emission for industrial

environments

2007

+A1:2011

EN 50121-4 Railway applications - Electromagnetic compatibility

Emission and immunity of the signalling and telecommunications

apparatus

2006

EN 60950-1 Information technology equipment - Safety - Part 1: General

requirements

2006

+A11: 2009

+A1: 2010

+A12: 2011

EN 50581 Technical documentation for the assessment of electrical and

electronic products with respect to the restriction of hazardous

substances

2012

The last two digits of the year in which the CE marking was affixed: 16

Pierre Öberg

Technical Manager

March 2016

1 Model Differences: x = 1 or 2 and indicates Software Class, y = optional and may indicate customer specific models.

6643-2230

Type tests and environmental conditions

Environmental phenomena Basic standard Description Test levels

Electrostatic discharge EN 61000-4-2 Enclosure Contact: ±6 kV

Air: ±8 kV

Fast transients EN 61000-4-4 Power port ±2 kV

Ethernet

Status out/Digital in

Serial ports

Enclosure

Surge EN 61000-4-5 Power port L-L: ±0.5 kV, 2 Ω, 18 μF

L-E: ±2 kV, 42 Ω, 0.5 μF

L-L: ±1 kV, 42 Ω, 0.5 μF

L-E: ±2 kV, 12 Ω, 9 μF

L-L: ±1 kV, 12 Ω, 9 μF

Ethernet L-E: ±2 kV, 2Ω, 0.5 μF

Status out/Digital in L-E: ±2 kV, 42 Ω, 0.5 μF

L-L: ±1 kV, 42 Ω, 0.5 μF

RS-232 L-E: ±2 kV, 2 Ω, 0.5 μF

Power frequency magnetic field EN 61000-4-8 Enclosure 300 A/m; 0, 16.7, 60 Hz

1000 A/m; 50 Hz

Pulsed magnetic field EN 61000-4-9 Enclosure 300 A/m

Radiated RF immunity EN 61000-4-3 Enclosure 20 V/m @ (80 – 2700) MHz

1 kHz sine, 80% AM

Conducted RF immunity EN 61000-4-6 Power port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz

Ethernet

Status out/Digital in

Serial ports

Earth port

Radiated RF emission CISPR 16-2-3

ANSI C63.4

(FCC part 15)

Enclosure Class B / DNV bridge

Conducted RF emission CISPR 16-2-1

ANSI C63.4

(FCC part 15)

Power port Class B / DNV bridge

Ethernet Class B

Dielectric strength EN 60950-1 Power port to all

other ports

1.5 kVrms, 50 Hz, 1 min

Ethernet ports to all

other ports

RS-232 port to all

other ports

6643-2230

Environmental

Temperatures EN 60068-2-1

EN 60068-2-2

Operating –40 to +70°C (–40 to +158°F)*

Storage and transport –50 to +85°C (–58 to +185°F)

Humidity EN 60068-2-30 Operating 5 to 95 % relative humidity

Storage and transport 5 to 95 % relative humidity

Altitude Operating 2 000 m / 70 kPa

MTBF MIL-C217F2,

Parts count

Ground Benign, 25°C

(77°F)

677 000 hours

Service life Operating 10 year

Vibration IEC 60068-2-6

(sine)

Operating 3 – 13.2 Hz: 1mm

13.2 – 100 Hz: 0.7 g

5.5 – 30 Hz: 1.5 g

30 – 50 Hz: 0.42 mm

50 – 500 Hz: 4.2 g**

IEC 60068-2-64

(random)

5 – 20 Hz: 2 m²/s³,

20 – 2000 Hz: – 3 dB/oct

Shock IEC 60068-2-27 Operating 30 g, 11 ms

100 g, 6 ms**

Bump IEC 60068-2-27 Operating 10 g, 11 ms

Packaging

Enclosure EN 60950-1 Zinc Fire enclosure

Dimension W x H x D

With connectors

52.5 x 100 x 101 mm

52.5 x 119 x 101 mm

Weight 0.7 kg

Degree of protection EN 60529 Enclosure IP 40

Cooling Convection

* Refer to “Safety” section in User Guide.

** Might require Ethernet cables to be fastened close to the unit.

6643-2230

Description

L105-S1/L205-S1 is an Industrial switch and device server made for harsh environments.

WeOS is the operating system of L105-S1/L205-S1 enabling the unit to operate in two

functional levels. The switch can be used in either 10 or 100 Mbit networks. Lynx DSS

L105-S1/L205-S1 has one serial port that supports RS-232.

Our unique FRNT (Fast Recovery of Network Topology) technology is the fastest

protocol on the market to re-configure a network in the event of any link or hardware

failure. That is why our products are used in safety critical applications such as tunnels,

traffic signal control and railway systems.

6643-2230

Interface specifications

Power

Operating voltage Rated: 24 to 48 VDC

Operating: 19 to 60 VDC

Rated current 140 mA (290 mA) @ 24 VDC (with 500 mA USB load)

70 mA (140 mA) @ 48 VDC (with 500 mA USB load)

Rated frequency DC

Inrush current, I2t 22.7·10-3 A2s @ 48 VDC

Startup current* 2 x Rated current

Polarity Reverse polarity protected

Redundant power input Ye s

Isolation to All other

Connection Detachable screw terminal

Connector size 0.2 – 2.5 mm2 (AWG 24 – 12)

Shielded cable Not required

* External supply current capability for proper start-up

Ethernet TX

Electrical specification IEEE std 802.3. 2005 Edition

Data rate 10 Mbit/s, 100 Mbit/s, manual or auto

Duplex Full or half, manual or auto

Circuit type TNV-1

Transmission range Up to 150 m with CAT5e cable or better*

Isolation to All other

Connection RJ-45, auto MDI/MDI-X

Cabling Shielded CAT5e or better is recommended

Conductive housing Ye s

Number of ports 4

* Refer to Safety section.

RS-232

Electrical specification EIA RS-232

Data rate 50 bit/s – 115.2 kbit/s

Data format 7 or 8 data bits, Odd, even or none parity, 1 or 2 stop bits

Protocol Transparent, optimised by packing algorithm

Circuit type SELV

Transmission range 15 m / 49 ft

Isolation to All other

Connection RJ-45 according to EIA-561

Shielded cable Recommended

Conductive housing Ye s

Number of ports 1

6643-2230

I/O / Relay output

Maximum voltage/current 60 VDC / 80 mA

Contact resistance Max 30 Ω

Isolation to All other

Connection Detachable screw terminal

Connector size 0.2 – 2.5 mm2 (AWG 24 – 12)

I/O / Digital input

Maximum voltage/load current 60 VDC / 2 mA

Voltage levels Logic one: >12V

Logic zero: <1V

Isolation to All other

Connection Detachable screw terminal

Connector size 0.2 – 2.5 mm2 (AWG 24 – 12)

USB

Electrical specification USB 2.0 host interface

Data rate Up to 12 Mbit/s (full-speed mode)

Circuit type SELV

Maximum supply current 500 mA

Connection USB receptacle connector type A

Console

Electrical specification LVTTL/LVCMOS-level

Data rate 115.2 kbit/s

Data format 8 data bits, no parity, 1 stop bit, no flow control

Circuit type SELV

Connection 2.5 mm jack, use only Westermo cable 1211-2027

RJ-45 connector (Front view)

Male Female

Pin 8

Pin 1

Pin 8

Pin 8 Pin 1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Westermo

Westermo

Westermo DR-250 Manual de usuario

Westermo

Westermo RedFox Manual de usuario

Westermo

Westermo Lynx 5600 Series Manual de usuario

Westermo

Westermo MRD-415 Manual de usuario

Westermo

Westermo MRD-310 Manual de usuario

Westermo

Westermo RT-370 Manual de usuario

Westermo

Westermo MRD-350 Manual de usuario

Westermo

Westermo DDW-02-B1 Manual de usuario

Westermo

Westermo Ibex-630 Series Manual de usuario

Westermo

Westermo SDW-550 E-mark Manual de usuario

Westermo

Westermo MRD-405 Manual de usuario

Westermo

Westermo RedFox Rail Manual de usuario

Westermo

Westermo Lynx L106-F2G Manual de usuario

Westermo

Westermo DR-260 Manual de usuario

Westermo

Westermo BRD-355 Manual de usuario

Westermo

Westermo SDI-550 Manual de usuario

Westermo

Westermo Viper-12 Series Manual de usuario

Westermo

Westermo ADSL-350 Manual de usuario

Westermo

Westermo Lynx Plus Manual de usuario

Westermo

Westermo LA-10 Manual de usuario

Westermo

Westermo RFI-219-T3G Manual de usuario

Westermo

Westermo BRD-355A Manual de usuario

Westermo

Westermo SDW-550 E-mark Manual de usuario

Westermo

Westermo MDI-118 Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad