Westell Interchange iQ 2000 Manual de usuario
InterChange
iQ 2000 and iQ 2000plus
User Guide
Acknowledgements
Information in this document is subject to change without notice and does not represent a
commitment on the part of Westell Limited. The software may be used or copied only in
accordance with the terms of the purchase agreement. It is against the law to copy the software
on any medium except as specifically allowed in the purchase agreement. No part of this manual
may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying or recording, for any purpose without the permission of Westell Limited.
Trademarks
Westell Limited recognises all third party trademarks.
Change History
Issue Product Status Date
010 Wes IiQ 2000 User Guide First Issue
020 Wes IiQ 2000 User Guide Phase 2 Dec 2000
030 Wes IiQ 2000 User Guide Frozen Apr 2001
040 Wes IiQ 2000 User Guide Restyle Mar 2002
050 Wes IiQ 2000 User Guide Update Jan 2003
060 IiQ 2000plus User Guide Revised Jun 2003
070 IiQ 2000plus User Guide Revised Nov 2004
Westell limited
Ringway House
Bell Road
Daneshill
Basingstoke
Hampshire, RG24 8FB
United Kingdom
Tel: +44 (0) 1256 843311
Fax: +44 (0) 1256 840429
email: [email protected]
www.westell.co.uk
© Copyright 2003, 2004 Westell limited
All rights reserved
Document number: UM 380 03 010
UM380 03 010 iii
User Guide
Contents
Acknowledgements 2
Trademarks 2
Change History 2
Preface 1
Scope of this Guide 1
Management 1
Vision iQ 2
1 Introduction 3
1.1 InterChange iQ 2000 3
1.2 InterChange iQ 2000plus 4
1.3 Management with Vision iQ 4
1.4 Environment 5
1.4.1 External Dimensions and Weight 5
1.4.2 Power Requirement 5
1.5 Approvals and Safety 5
2 Hardware Installation Procedure 6
2.1 Introduction to Unit Installation 6
2.2 Unit Installation 6
2.2.1 Unpacking and Inspection 6
2.2.2 Hardware Installation 7
Back Panel Equipment 7
2.3 Power-On and Self-Test 9
2.3.1 Terminal Connections 9
2.3.2 Self-Test 9
2.4 Vision iQ Management Software Installation 10
2.5 InterChange iQ 2000 and 2000plus Installation 10
2.5.1 Set Factory Default Values 11
2.5.2 Set Time and Date 11
2.5.3 Protocol Configuration 12
2.5.4 Configuration using the Quick Start wizard 13
2.5.5 Configuration changes (for manual changes to the default settings) 13
2.6 Cabling into a Management System 14
2.6.1 Alarm Signal Cabling 14
2.6.2 Alarm Signal Cable Test 14
2.6.3 Management Terminal Cabling 14
2.6.4 Management Terminal Cable Connection Test 14
2.7 Network Cabling 15
2.7.1 Port Usage 15
2.7.2 Cabling Practice 15
2.7.3 Cabling Procedure 15
iv UM380 03 010
InterChange iQ 2000 and iQ 2000plus
3 Switches and LEDs 17
3.1 Switches 17
3.1.1 Power ON/OFF switch 17
3.1.2 Sync switch 17
3.1.3 Port Impedance switches 17
3.2 Front Panel LEDs 17
3.2.1 Status LEDs 17
3.2.2 LAN LEDs 18
3.2.3 Port LEDs 18
3.2.4 Power LED 18
4 Management using Vision iQ 19
4.1 Configuration 19
4.2 Upgrade Configuration Procedure 19
4.3 Software Components 19
4.4 PC to InterChange Connection 19
4.4.1 Serial Link 19
4.4.2 Ethernet Connection 20
4.4.3 PC Specification 20
4.5 Software Installation 20
4.6 Configuring Vision iQ for use with InterChange iQ 2000 units 21
4.6.1 Starting Vision iQ 21
4.6.2 Working with Vision iQ 21
4.6.3 Vision iQ Mode Options 22
4.7 Connect 23
4.7.1 Connection 23
4.7.2 Disconnect 24
4.7.3 Reconnect 24
4.7.4 Shelf Definitions 24
4.7.5 Shelf Properties Group 25
4.7.6 Shelf Definitions Present Group 25
4.7.7 Define Poll List 27
4.7.8 Global Poll 28
4.8 Diagnostics 29
4.8.1 Diagnostics Overview 29
4.8.2 System Page 30
4.8.3 Module Page 30
4.8.4 Hardware Page 31
4.9 Major Alarms 31
4.10 Port Errors 32
4.11 Call Statistics 33
4.12 Loopback 34
4.13 Using the Configuration Wizard 34
4.14 InterChange iQ 2000plus Enhancements 43
4.14.1 Proxy Diversion 43
4.14.2 Redirection Timeout 43
4.14.3 Q.932 Redirecting Number Information 44
4.14.4 CCM Message Waiting Indication 44
4.14.5 Configuration Wizard Variation 44
UM380 03 010 v
User Guide
5 Conversions and Transparency 45
5.1 Q.931/DPNSS Conversion 45
5.1.1 Default Configuration 45
5.1.2 Configuration Options 45
5.2 Transparent Signalling 47
5.2.1 Overview 47
5.2.2 Supported Services 47
5.3 Interworking Between DPNSS & QSIG Equipment 48
5.4 IiQ 2000plus Proxy Interworking Between DPNSS & Q.931 49
5.5 Interworking DPNSS with Cisco Call Manager 50
6 Manual Configuration or Upgrade of Software
Protocol Options 52
6.1 General Module Configuration Procedure 52
6.1.1 The Configuration Menu System 52
6.1.2 Menu Help Facilities 52
6.1.3 Confirming Configuration Changes 52
6.2 Manual Configuration and Upgrade Options 53
6.2.1 Resource Manager Configuration (MGMT) 53
6.2.2 Channel 0 Configuration (CZ) - Delay Timers 53
6.3 Q.931/DPNSS Conversion Configuration 54
6.3.1 Port 1 (Q.931 port) Configuration 54
6.3.2 Port 2 (DPNSS port) Configuration 55
6.4 DPNSS/QSIG Transparency Options Configuration 57
6.4.1 DPNSS/QSIG Transparency 57
6.5 Advanced Service Interworking 58
6.5.1 DPNSS Message Waiting Implementations 58
6.5.2 ISDX Voice Messaging Systems 59
6.5.3 Name Mapping 59
6.5.4 Route Optimisation Options 60
6.5.5 QSIG Facility Element Encoding 60
6.5.6 QSIG Diversion Restriction 61
6.6 Configuring InterChange iQ 2000plus Proxy Services 63
6.6.1 Proxy Diversion Address Filtering 63
6.6.2 Operator Redirection 64
6.6.3 Service Spoofing 64
7 Problem Determination 65
7.1 Introduction 65
7.2 Power-On Problems 65
7.3 Operational Problems 66
7.4 Diagnostic Procedures 68
7.4.1 Power Supply 68
7.4.2 Self Test Failure 68
7.4.3 Port Failure Alarm 68
7.4.4 Checking Cables 69
7.4.5 Loop-Back Testing 70
7.4.6 Call Failures 70
7.4.7 Fatal Errors 71
7.4.8 Event Reporting 72
7.4.9 SNMP Traps 72
7.4.10 Call Tracing 73
vi UM380 03 010
InterChange iQ 2000 and iQ 2000plus
8 DPNSS Compliance Tables 74
8.1 Basic Call 74
8.2 Data Call 74
8.3 Executive Intrusion (Partial Support) 75
8.4 Diversion 76
8.4.1 Diversion - Immediate 76
8.4.2 Diversion - On Busy 78
8.4.3 Diversion - On-No-Reply 79
8.5 Hold 80
8.6 Three Party 81
8.7 Call Offer 82
8.8 Service Independent Strings 82
8.9 Bearer Service Selection 83
8.10 Route Optimisation 83
8.11 Redirection 84
8.12 Centralised Operator 86
8.13 Add-On Conference 88
8.14 Do Not Disturb 89
8.15 Loop Avoidance 89
8.16 Network Address Extension 90
Appendices
A Approvals, Safety Instructions and Statutory Information 91
B References & Technical Specifications 98
C Cabling Specifications 102
D Glossary of Terms 104
UM380 03 010 1
User Guide
Preface
Scope of this Guide
This Guide describes the hardware and software of the Vision iQ managed InterChange
iQ 2000 and iQ 2000plus products, the installation, maintenance and general operation.
The Guide is divided into the following sections:
Chapter 1 Introduction.
Chapter 2 Hardware Installation Procedure.
Chapter 3 Switches and LEDs.
Chapter 4 Management using Vision iQ.
Chapter 5 Conversions and Transparency.
Chapter 6 Manual Configuration or Upgrade of Software Protocol Options.
Chapter 7 Problem Determination.
Chapter 8 DPNSS Compliance Tables.
Appendices
A Approvals,Safety Instructions and Statutory Information
B References and Technical Specifications
C Cabling Specifications
D Glossary of Terms
Management
InterChange iQ 2000 products are designed for years of error-free running with little, or no,
requirement for management involvement once initial set-up is complete. Normally
any network faults are notified and diagnosed from alarms provided by the attached
equipment, after interaction with the InterChange unit, and it is superfluous and confusing to
network operations staff to have these indications repeated at a second interface.
For the rare cases where installation philosophy requires direct notification of alarms,
InterChange iQ 2000 and iQ 2000plus have four types of management interface:
• LEDs,
• A relay which can make or break an alarm circuit in the event of a major hardware
related failure,
• An RS-232 serial interface which can be used for fault diagnosis and configuration
management, either from a locally connected PC running Vision iQ, or from a
remote PC via a modem link, and
• Ethernet.
These interfaces operate concurrently and quite independently.
2 UM380 03 010
InterChange iQ 2000 and iQ 2000plus
Vision iQ
Vision iQ is a Windows application for managing the InterChange iQ 2000 and iQ 2000plus.
Vision iQ is used to download protocol conversion software to the InterChange unit from a PC,
using the Download utility. The product is configured using the Vision iQ application described in
this manual. Vision iQ also manages the operational, diagnostic and alarm information for each
port used in the conversion or channel grouping.
Vision iQ identifies the software and hardware facilities available on an InterChange unit and
displays parts or all of the configuration and management dialogues accordingly.
UM380 03 010 3
Introduction
1 Introduction
1.1 InterChange iQ 2000
InterChange iQ 2000 is a dual port ISDN unit designed to perform signalling and service
reconciliation between two unlike ISDN signalling systems.
It is typically deployed to attach:
• a QSIG (or DPNSS) PBX to a DPNSS (or QSIG) network, or
• a number of DPNSS PBXs to a QSIG or Q.931 backbone (e.g. VoIP or ATM)
network, or
• a DPNSS PBX to a Q.931-based Public ISDN service (such as ‘ISDN 30e’).
When attaching a QSIG (or DPNSS) PBX to a DPNSS (or QSIG) network,
InterChange iQ 2000 provides seamless service interworking between the attached PBX and
other PBXs in the network, including inter-operation of most of the commonly used services.
InterChange iQ 2000 facilitates basic call interworking, including simple services such as
calling and connected identity when attaching a number of DPNSS PBXs to a QSIG or Q.931
backbone network, or a DPNSS PBX to a Q.931-based Public ISDN service.
In addition, when attaching a number of DPNSS PBXs to a QSIG or Q.931 backbone
network and the core network supports QSIG signalling, InterChange iQ 2000 can transport
DPNSS signalling across the network and deliver it practically transparently via a similar
InterChange unit to a remote DPNSS PBX. In this mode all DPNSS Supplementary Services
are supported apart from some link-specific Traffic Channel maintenance services.
InterChange iQ 2000 supports 2 E1
Primary Rate [2 Mbit/s (30B + D) Common Channel
Signalling] interfaces; providing a single Primary Rate conversion. It
is a portable unit that can
be mounted on a desk. A kit of brackets is also available to allow the unit to be installed on a 19
inch rack. It is particularly suited for use in Customer Premises Environments (CPE) to interface
equipment into Virtual Private Networks.
Figure 1: InterChange iQ 2000 in a Private Network.
4 UM380 03 010
InterChange iQ 2000 and iQ 2000plus
Figure 1 shows DPNSS PBXs interconnected across a QSIG network. In this configuration,
the combination of InterChange units and the network behave as a single DPNSS transit
node and transports DPNSS supplementary signalling.
Figure 2: InterChange iQ 2000 in a CPE.
Figure 2 shows an InterChange iQ 2000 interfacing a PBX using the UK standard DPNSS
protocol to the QSIG/Q.931 protocol.
Conversions operate on the common signalling channel only. Bearer circuits are passed directly
through the unit. Each protocol support is configurable to meet specific application needs.
The Virtual Private Network protocol support can be configured to operate into sub-equipped
ISDN trunks, allowing the user to maximise the benefits of the advantageous Primary Rate
ISDN tariffs now being offered by some PTOs.
1.2 InterChange iQ 2000plus
The IiQ 2000plus is a variation of the InterChange iQ 2000 providing some additional
facilities:
• The ability to perform diversions on behalf of the PBX; and
• Support for the Q.932 ‘redirecting number’ element for diversion;
• Advanced Wizard custom configuration for Cisco Call Manager;
• The ability to display DPNSS Message Waiting Indications on telephones
controlled by Cisco Call Manager.
If a unit is first installed with version R.2.1.0 of the operating software, an IiQ 2000 may be
upgraded to an IiQ 2000plus. For more information on the upgrade, contact your distributor /
reseller or Westell Account Manager.
1.3 Management with Vision iQ
Vision iQ, the Management Interface, provides the facilities to connect (locally or remotely) to an
InterChange iQ 2000 or iQ 2000plus, display diagnostic information and configure the unit.
Vision iQ allows you to:
• connect and disconnect from the management terminal,
• set up a definition for the InterChange iQ 2000 or iQ 2000plus unit,
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Puerta de Westell
Westell
Westell RMC-7XX-G Manual de usuario
Westell
Westell 2410 Manual de usuario
Westell
Westell VersaLink 327W Manual de usuario
Westell
Westell 826010 Manual de usuario
Westell
Westell Media Gateway WMT Manual de usuario
Westell
Westell VersaLink 327W Manual de usuario
Westell
Westell VersaLink 7550 Manual de usuario
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
