WELLTECH ATA-151 Manual de usuario

ATA-151/152

Quick Guide

1. Copyright declaration

The copyright of the content which been

mentioned in this manual is owned by Welltech

computer Co., Ltd.

The copyright of brand and mark which been

mentioned is belong to its own company.

2005 Copyright Welltech computer Co., Ltd.

2. Before installation

Please check the following items before the

installation, that can avoid some unknown

problems during installation:

1.Preparing the following equipment for

installation:

a. A pc with network connection.

b. Ethernet RJ-45 cable

c. Phone and RJ-11 cable

2.Prepareing 1 of the following Network connection:

a. Static IP: a valid fixed IP address

b. DHCP: Make sure the DHCP server is

available.

c. PPPoE: Prepare a valid username and

password, further more,

confirm the XDSL modem is

functional.

3.Power

Make sure the power supply is adaptable.

3. Check the accessories

Please check the accessories after you open the

packing, there should have the parts as list in

below:

a. ATA mainframe X 1

b. 1M Ethernet RJ-45 cable with X 1

c. DC 12V, 1A Power adapter X 1

d. Document CD X 1, there is User guide and Quick

guide is embedded.

4.Physical Interface

4.1 Indicator

4.2 Connection port

6.For backing to factory default if this button is

pressed over 5 seconds.

7.For PC to connect to network with a RJ-45

ethernet cable that via ATA-151/152.

8. For ATA-151/152 to connect to a private network

or internet with a RJ-45 ethernet cable.

9. For connecting to PSTN(Fixed line) with a RJ-11

cable as backup if network failed.

10. For connecting to a analog telephone with a RJ-

11 cable.

11. Connect power adapter here.

1.PC connecting indicator

Light on: PC is connected

Light off: PC is disconnected

2.Network connecting indicator

Light on: Network is standby

Light off: Network is failed

Light flash: Data is transmitting

3.Phone active indicator

Light on: Phone is picked up

Light off: Phone is standby

Light flash: Incoming call

4.Registration indicator

Light on: Register is successful

Light flash: Register is failed

5.Power indicator

Light on: Power is ok

Light off: Power is failed

tatu

Ph eon

LAN

wer

ATA-151

Figure 1.

Figure 2.

67891011

ATA-151

ATA-152

1. Copyright declaration

The copyright of the content which been

mentioned in this manual is owned by Welltech

computer Co., Ltd.

The copyright of brand and mark which been

mentioned is belong to its own company.

2005 Copyright Welltech computer Co., Ltd.

2. Before installation

Please check the following items before the

installation, that can avoid some unknown

problems during installation:

1.Preparing the following equipment for

installation:

a. A pc with network connection.

b. Ethernet RJ-45 cable

c. Phone and RJ-11 cable

2.Prepareing 1 of the following Network connection:

a. Static IP: a valid fixed IP address

b. DHCP: Make sure the DHCP server is

available.

c. PPPoE: Prepare a valid username and

password, further more,

confirm the XDSL modem is

functional.

3.Power

Make sure the power supply is adaptable.

3. Check the accessories

Please check the accessories after you open the

packing, there should have the parts as list in

below:

a. ATA mainframe X 1

b. 1M Ethernet RJ-45 cable with X 1

c. DC 12V, 1A Power adapter X 1

d. Document CD X 1, there is User guide and Quick

guide is embedded.

4.Physical Interface

4.1 Indicator

4.2 Connection port

6.For backing to factory default if this button is

pressed over 5 seconds.

7.For PC to connect to network with a RJ-45

ethernet cable that via ATA-151/152.

8. For ATA-151/152 to connect to a private network

or internet with a RJ-45 ethernet cable.

9. For connecting to PSTN(Fixed line) with a RJ-11

cable as backup if network failed.

10. For connecting to a analog telephone with a RJ-

11 cable.

11. Connect power adapter here.

1.PC connecting indicator

Light on: PC is connected

Light off: PC is disconnected

2.Network connecting indicator

Light on: Network is standby

Light off: Network is failed

Light flash: Data is transmitting

3.Phone active indicator

Light on: Phone is picked up

Light off: Phone is standby

Light flash: Incoming call

4.Registration indicator

Light on: Register is successful

Light flash: Register is failed

5.Power indicator

Light on: Power is ok

Light off: Power is failed

uSa s

LAN

werPo

ATA-151

Figure 1.

Figure 2.

67891011

ATA-151

ATA-152

5. Start to installation

The following will show you how to install and

configure the ATA-151/152 step by step.

Scenario 1. XDSL connection

Connect to XDXL modem directly.

Please refer the figure 3 to install.

Step 1.

Plug RJ-45 cable for connecting from LAN port to

XDSL modem..

Step 2.

Plug RJ-11 cable for connecting to a valid analog

phone.

Step 3.

Plug RJ-11 cable CO PSTN line into PSTN port.

Step 4.

Plug the power adapter with valid power into DC 12V

port for getting adaptable power to ATA.

Step 5.

Now, please check the LED indicator for make sure if

the LED status as the following:

1. Power: ON

2. Status: Blinking

3. Phone: It should be off, if the handset of

analog phone is not picked up

4. LAN: ON

5. PC: ON

Step 6.

Plug RJ-45 cable for connecting from PC port.

Note:

Please disable the fuirewall to prevent some

error that during configuration if there is any

firewall software is installed. You can restart

the firewall after the configuration is finished.

PSTN

CO line

XDSL Modem

Figure 3.

Scenario 1.1. Cordless connection

Also you can connect a cordless phone to ATA for

instead of a cord phone as figure 5 if you don't

want to be limited by a annoying cord, and there is

no any special setting.

Scenario 2 HUB connection

Connect to HUB or switch HUB directly.

Please refer the figure 6 to install.

All of step of setup is same with scenario 1.

PSTN

CO line

XDSL Modem

Figure 5.

PSTN

CO line

XDSL Modem

Figure 6.

HUB

5. Start to installation

The following will show you how to install and

configure the ATA-151/152 step by step.

Scenario 1. XDSL connection

Connect to XDXL modem directly.

Please refer the figure 3 to install.

Step 1.

Plug RJ-45 cable for connecting from LAN port to

XDSL modem..

Step 2.

Plug RJ-11 cable for connecting to a valid analog

phone.

Step 3.

Plug RJ-11 cable CO PSTN line into PSTN port.

Step 4.

Plug the power adapter with valid power into DC 12V

port for getting adaptable power to ATA.

Step 5.

Now, please check the LED indicator for make sure if

the LED status as the following:

1. Power: ON

2. Status: Blinking

3. Phone: It should be off, if the handset of

analog phone is not picked up

4. LAN: ON

5. PC: ON

Step 6.

Plug RJ-45 cable for connecting from PC port.

Note:

Please disable the fuirewall to prevent some

error that during configuration if there is any

firewall software is installed. You can restart

the firewall after the configuration is finished.

PSTN

CO line

XDSL Modem

Figure 3.

Scenario 1.1. Cordless connection

Also you can connect a cordless phone to ATA for

instead of a cord phone as figure 5 if you don't

want to be limited by a annoying cord, and there is

no any special setting.

Scenario 2 HUB connection

Connect to HUB or switch HUB directly.

Please refer the figure 6 to install.

All of step of setup is same with scenario 1.

PSTN

CO line

XDSL Modem

Figure 5.

PSTN

CO line

XDSL Modem

Figure 6.

HUB

7. Configuration

Section 1. Configure your PC

Step 1.

Double click "My network places "

Step 2.

Click "View network connections"

Step 3.

Right -click "Local Area connection" then select

"Properties"

Step 4.

Step 5.

Step 6. Run Iexplorer

Step 7. Input 192.168.123.123

Click "Internet Protocol (TCP/IP)"

Click Obtained an IP automatically

7. Configuration

Section 1. Configure your PC

Step 1.

Double click "My network places "

Step 2.

Click "View network connections"

Step 3.

Right -click "Local Area connection" then select

"Properties"

Step 4.

Step 5.

Step 6. Run Iexplorer

Step 7. Input 192.168.123.123

Click "Internet Protocol (TCP/IP)"

Click Obtained an IP automatically

Step 8. Please input "root" as a username then

enter, then you will login into the configuration WEB

page.

Step 9. Click "Installation wizard"

Step 10. Click next which on right-button of the

screen.

Step 11.There are 3 options for you to select.

1. Static IP - Please goto step 12.

2. DHCP - Please goto step 14.

3. PPPoE - Please goto step 15.

Step 12. The first option is for you to configure a

valid static IP.

Step 13. You can fill the IP address, Subnet mask

and gateway IP here. Please goto step 18 after this

step.

Step 14.DHCP mode is for you to configure the ATA

if you used dynamic IP already, the option will be

better for you. Please goto step 18 after you finish

this step.

Step 15.PPPoE mode is another option if you had

got a account and password from your ISP.

Step 8. Please input "root" as a username then

enter, then you will login into the configuration WEB

page.

Step 9. Click "Installation wizard"

Step 10. Click next which on right-button of the

screen.

Step 11.There are 3 options for you to select.

1. Static IP - Please goto step 12.

2. DHCP - Please goto step 14.

3. PPPoE - Please goto step 15.

Step 12. The first option is for you to configure a

valid static IP.

Step 13. You can fill the IP address, Subnet mask

and gateway IP here. Please goto step 18 after this

step.

Step 14.DHCP mode is for you to configure the ATA

if you used dynamic IP already, the option will be

better for you. Please goto step 18 after you finish

this step.

Step 15.PPPoE mode is another option if you had

got a account and password from your ISP.

Step 16. Please input the account and password

here which given by your ISP.

Step 17. Click "Next"

Step 18. There are 2 of operation

mode for you to choose, one "Proxy

mode", another is "P2P mode".

You can choose "Proxy mode" if you

can get service from a voice service

provider or there is a valid service

platform in your place already,

otherwise we recommend you to

choose "P2P" mode.

Follow the steps in below if the "Proxy mode"

is selected.

Step 19. To fill the Primary Proxy Address with a

valid IP address which given by your provider.

Step 20. You can ignore to fill the secondary

proxy address if it is not provided.

Step 21. The Outbound proxy is same with last

step, unless the provider has offered such

configuration, otherwise you can ignore it directly.

Step 22. Input the phone number, registration

account and password which issued by your

provider.

Step 23. Click "OK

Step 24. Normally. all of the port configuration

can be ignored if the provider has not specified.

Please goto step

Follow the steps if the "P2P mode" is selected.

Notice: Basically, in proxy mode the provider will

record the number of ATA into a database after the

registration is successful. So you can pick-up the

phone then dial a number directly. But there is no

any provider if "P2P mode" is selected, so you need

to configure The number which you will dial in the

future by manual.

Step 25. Please configure the number which you

will dial via the following steps.

Step 26.Click the Arrow beside "Advanced

Configuration" then click "Number Configuration".

Step 27. You can find the "Phone book"

configuration on major-screen.

Step 28. The Phone Book is for you to define the

number for your called party.

Example:

If You want to define a number for your friend who

had a same product.

1. Input the digits as a index, it can be defined by

yourself.

2. Give a name as a note for easy

to recognize.

3. Define a "e.164 number" for

the called party that for you

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Puerta de WELLTECH

WELLTECH

WELLTECH 2504 Manual de usuario

WELLTECH

WELLTECH FTP PROVISION Instrucciones de funcionamiento

WELLTECH

WELLTECH WellGate 3511N Manual de usuario

WELLTECH

WELLTECH WILLGATE26XX - RELEASE NOTE V106B Manual de usuario

WELLTECH

WELLTECH 5290 - SS7 PARAMETERS REQUIREMENT Manual de usuario

WELLTECH

WELLTECH 3802 - RELEASE NOTE V105 Manual de instrucciones

WELLTECH

WELLTECH 3701 - RELEASE NOTE V106A Manual de instrucciones

WELLTECH

WELLTECH FXO-08 - V2.0A Manual de usuario

WELLTECH

WELLTECH WELLGATE 2608 - V1.00 Manual de usuario

WELLTECH

WELLTECH WellGate 3512 Manual de usuario

WELLTECH

WELLTECH FXS H.323 Gateway Manual de usuario

WELLTECH

WELLTECH FXO - LEARN AND RECORD DISCONNECT TONE Manual de usuario

WELLTECH

WELLTECH FXSO GATEWAY H.323 3701A - VERSION 1.0 Manual de usuario

WELLTECH

WELLTECH FXO - RECORD NEW GREETING Manual de usuario

WELLTECH

WELLTECH FXO SIP GATEWAY - V105 Manual de usuario

WELLTECH

WELLTECH FXSO GATEWAY H.323 3701A - VERSION 2.1A Manual de usuario

WELLTECH

WELLTECH 3802 - RELEASE NOTE V106 Manual de instrucciones

WELLTECH

WELLTECH ATA171PLUS - Manual de usuario

WELLTECH

WELLTECH 2424s FXS Manual de usuario

WELLTECH

WELLTECH FXO GATEWAY H.323 3802 Manual de usuario

WELLTECH

WELLTECH WILLGATE26XX - RELEASE NOTE V105B Manual de usuario

WELLTECH

WELLTECH 5260 V6.0 JSP - UPGRADE PROCEDURE Manual de usuario

WELLTECH

WELLTECH WILLGATE26XX - RELEASE NOTE 2 V106C Manual de usuario

WELLTECH

WELLTECH 3701 - RELEASE NOTE V106 Manual de instrucciones

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario