Weidmüller Premium Line IE-SW-PL10M Series Manual

Ethernet Switch –Premium Line

IE-SW-PL10M Series (Managed)

Hardware Installation Guide

Fourth Edition, August 2016

1243400000/03/08.16

Please note:

This document, the detailed manual and any further

product information - if available - can be

downloaded at the internet link:

http://www.weidmueller.com/downloads

Reproduction without permission is prohibited.

- 2 -

Package Checklist

Your Ethernet switch is shipped with the following items. If any of these

items are missing or damaged, please contact your Weidmüller customer

service for assistance.

1 Ethernet Switch IE-SW-PL10M

Hardware Installation Guide

CD-ROM with User’s Manual and Windows Utility (option)

Please download CD-ROM from Internet page

http://www.weidmueller.com/downloads

RJ45 to DB9 console port cable

Protective caps for unused ports

Optional Accessories

SFP-Transceiver (Fast Ethernet and Gigabit Ethernet modules for different

transmission lengths)

EBR-Module RS232 (Automatic Backup Configurator via RS-232 Console

Port)

RM-KIT (19” Rack mounting kit)

Detailed information in datasheet

- 3 -

Panel Views of IE-SW-PL10M Series

1. 1 to 7: 10/100BaseT(X) port

2. G1:

IE-SW-PL10M-3GT-7TX

10/100/1000BaseT(X) port

IE-SW-PL10M-1GT-2GS-7TX

10/100/1000BaseT(X) port

3. G2:

IE-SW-PL10M-3GT-7TX

10/100/1000BaseT(X) port

IE-SW-PL10M-1GT-2GS-7TX

1000BaseSX/LX/LHX/ZX port

4. G3:

IE-SW-PL10M-3GT-7TX

10/100/1000BaseT(X) port

IE-SW-PL10M-1GT-2GS-7TX

1000BaseSX/LX/LHX/ZX port

5. G1, G2, G3: LED indicators for

1000 Mbps ports

6. PWR1: LED for power input 1

7. PWR2: LED for power input 2

8. FAULT: LED indicator

9. MSTR/HEAD: LED indicator

10. CPLR/TAIL: LED indicator

11. Label

12. 100M: LED indicator for TP port

13. 10M: LED indicator for TP port

14. Article Number

IE-SW-PL10M-1GT-2GS-7TX

Front Panel View

IE-SW-PL10M-3GT-7TX

Front Panel View

- 4 -

Top Panel:

1. Ground screw

2. RS-232 console port

3. Heat dissipation orifices

4. DIP switches for Ring Master,

Ring Coupler, and Turbo Ring

5. 6-pin terminal block for DI 1, DI 2,

and PWR 2

6. 6-pin terminal block for PWR1,

Relay 1, and Relay 2

Rear Panel:

7. Screw holes for Wall Mounting Kit

8. DIN-Rail Kit

Mounting Dimensions (unit = mm)

- 5 -

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the back

panel of the IE-SW-PL10M when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate to the IE-SW-PL10M, make sure the

stiff metal spring is situated towards the top, as shown by the following

figures.

STEP 1—Insert the top of the

DIN-Rail into the slot just below the

stiff metal spring.

STEP 2—The DIN-Rail attachment

unit will snap into place as shown in

the following illustration.

To remove the IE-SW-PL10M switch from the DIN-Rail, simply reverse Steps

1 and 2 above.

ATEX Information

1. Certificate number DEMKO 11 ATEX 150190X

2. Ambient range (-40°C ≤Tamb ≤75°C)

3. Certification string (Ex nA nC IIC T4 Gc)

4. Standards covered (EN 60079-0:2012+A11:2013,

EN 60079-15:2010)

5. The conditions of safe usage:

These products must be mounted in an IP54 enclosure.

Install in an area of pollution degree 2 or less.

Use a conductor wire of size 0.2 mm² or greater.

PROVISIONS SHALL BE MADE, EITHER IN EXTERNAL TO

THE APPARATUS, TO PREVENT THE RATED VOLTAGE BEING

EXCEEDED BY THE TRANSIENTS DISTURBANCES OF MORE

THAN 40 %

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

Safety Extra-Low Voltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

Safety Extra-Low Voltages (SELV) in compliance with IEC950/

EN60950/ VDE0805.

- 6 -

ATTENTION

This unit is a built-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation IEC 60950/EN60950 (or

similar regulation).

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Ethernet Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

Use separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately

You can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together

You should separate input wiring from output wiring

We advise that you label the wiring to all devices in the system.

Grounding the IE-SW-PL10M

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface such as a metal panel.

- 7 -

Wiring the Relay Contact

The IE-SW-PL10M has two sets of relay outputs—relay 1 and relay 2. Each

relay contact uses two contacts of the terminal block on the IE-SW-PL10M´s

top panel. Refer to the next section for detailed instructions on how to

connect the wires to the terminal block connector, and how to attach the

terminal block connector to the terminal block receptor. In this section, we

illustrate the meaning of the two contacts used to connect the relay contact.

FAULT:

The two sets of relay contacts of the

6-pin terminal block connector are

used to detect user-configured events.

The two wires attached to the fault

contacts form an open circuit when a

user-configured event is triggered. If a

user-configured event does not occur,

the fault circuit remains closed.

Wiring the Redundant Power Inputs

The IE-SW-PL10M has two sets of power inputs—power input 1 and power

input 2. The top two contacts and the bottom two contacts of the 6-pin

terminal block connector on the IE-SW-PL10M´s top panel are used for the

two digital inputs. The top and front views of one of the terminal block

connectors are shown here.

STEP 1: Insert the negative/positive

DC wires into the V-/V+ terminals,

respectively.

STEP 2: To keep the DC wires from

pulling loose, use a small flat-blade

screwdriver to tighten the wire-clamp

screws on the front of the terminal

block connector.

STEP 3: Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on the IE-SW-PL10M´s top

panel.

- 8 -

Wiring the Digital Inputs

The IE-SW-PL10M has two sets of digital inputs, DI 1 and DI 2. Each DI

consists of two contacts of the 6-pin terminal block connector on the

IE-SW-PL10M´s top panel, which are used for the two DC inputs. The top

and front views of one of the terminal block connectors are shown here.

STEP 1: Insert the negative

(ground)/positive DI wires into the ┴/I1

terminals, respectively.

STEP 2: To keep the DI wires from

pulling loose, use a small flat-blade

screwdriver to tighten the wire-clamp

screws on the front of the terminal block

connector.

STEP 3: Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is located on the

IE-SW-PL10M´s top panel.

Communication Connections

Each IE-SW-PL10M switch has 3 types of communication ports:

1 RJ45 console port (RS-232 interface)

7 10/100BaseTX Ethernet ports

3 Gigabit Ethernet ports:

3 10/100/1000BaseTX ports, or 1 10/100/1000BaseTX and 2

1000BaseSFP (mini-GBIC) ports

In this section, we present two types of diagrams—Pinout Diagrams and

Cable Wiring Diagrams—that convey information about the ports and the

cables used to connect the IE-SW-PL10M Series to other devices:

Pinouts—The “Pinouts” diagrams display the type of signal passing through

each of the port’s pins.

Cable Wiring—The “Cable Wiring” diagrams present standard cable wiring

schemes for cables used to connect the IE-SW-PL10M Series ports to other

devices. These diagrams display three pieces of information:

1. When building your own cable, refer to the “pin-to-pin” cable wiring

information displayed between the two vertical dashed lines to see

which pin of the connector on the left should be connected to which pin

of the connector on the right.

2. The information to the left of the left vertical dashed lines gives the

pinouts of the relevant IE-SW-PL10M Series port.

3. The information to the right of the right vertical dashed line gives the

pinouts of the opposing device’s port.

NOTE

1. The pin numbers for male DB9 connectors and hole numbers

for female DB9 connectors are labeled on the connector.

2. The pin numbers for 10-pin RJ45 connectors (and ports) are

typically not labeled on the connector (or port). Refer to the

following Pinout and Cable Wiring diagrams to see how

10-pin RJ45 pins are numbered

- 9 -

RS-232 Connection

The IE-SW-PL10M Series has one RS-232 (10-pin RJ45) console port,

located on the top panel. Use either an RJ45-to-DB9 (see the cable following

wiring diagrams) to connect the IE-SW-PL10M console port to your PC’s

COM port. You may then use a console terminal program, such as Windows

Hyper Terminal, to access the IE-SW-PL10M console configuration utility.

RJ45 (10-pin) Console Port Pinouts

Description

------

DSR

------

GND

TxD

RxD

GND

------

DTR

------

RJ45 (10-pin) to DB9 (F) Cable Wiring

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the IE-SW-PL10M Series front panel

are used to connect to Ethernet-enabled devices. Most users configure these

ports for Auto MDI/MDI-X mode, in which case the port’s pinouts are

adjusted automatically depending on the type of Ethernet cable used

(straight-through or cross-over), and the type of device (NIC-type or

HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

RJ45 (8-pin, MDI) Port Pinouts

Signal

Tx+

Tx-

Rx+

Rx-

Server

- 10 -

RJ45 (8-pin, MDI-X) Port Pinouts

Signal

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Cross-over Cable Wiring

1000BaseT Ethernet Port Connection

1000BaseT data is transmitted on differential TRD+/- signal pairs over copper

wires.

MDI/MDI-X Port Pinouts

Signal

TRD(0)+

TRD(0)-

TRD(1)+

TRD(2)+

TRD(2)-

TRD(1)-

TRD(3)+

TRD(3)-

Otros manuales para Premium Line IE-SW-PL10M Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Weidmüller

Weidmüller

Weidmüller IE-SW-EL08-8GT Manual

Weidmüller

Weidmüller IE-SW-EL08-8PoE Manual

Weidmüller

Weidmüller Value Line IE-SW-VL05M Series Manual

Weidmüller

Weidmüller IE-SW-SL28M Manual de usuario

Weidmüller

Weidmüller IE-SW-EL10-8GTPoE-2GESFP Manual

Weidmüller

Weidmüller IE-SW-EL18-16TX-2GC Manual

Weidmüller

Weidmüller Premium Line IE-SW-PL10M Series Manual

Weidmüller

Weidmüller ValueLine IE-SW-VL08-GT Series Manual

Weidmüller

Weidmüller IE-SW-AL05M-5TX Manual de usuario

Weidmüller

Weidmüller IE-SW-BL05-4GT-1GS Manual

Weidmüller

Weidmüller Gigabit Advanced IE-SW-AL06M-4GTPoE-2GESFP Manual

Weidmüller

Weidmüller IE-SW-EL08-6TX-2SC Manual

Weidmüller

Weidmüller PV Next Series Manual de usuario

Weidmüller

Weidmüller IE-SW-AL08M-8GT Manual

Weidmüller

Weidmüller IE-SW-EL24-24TX Manual

Weidmüller

Weidmüller IE-SW-EL05-5TX Manual

Weidmüller

Weidmüller IE-SW-BL05-5GT Manual

Weidmüller

Weidmüller Premium Line IE-SW-PL08M Series Manual

Weidmüller

Weidmüller IE-SW-AL24M-24TX Manual

Weidmüller

Weidmüller Substation IE-SW-SL26M-24TX-2GC Manual de usuario

Weidmüller

Weidmüller 2682340000 Manual

Weidmüller

Weidmüller Gigabit Advanced IE-SW-AL08M-8GTPoE Manual

Weidmüller

Weidmüller IE-SW-AL08M-8GT Manual

Weidmüller

Weidmüller Premium Line IE-SW-PL08M Series Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario