Weider Pro 4850 831.153932 Manual de usuario

WEIGHT SYSTEM EXERCISER

User’s Manual

Patent Pending

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Model No. 831.153932

Serial No.

Write the serial number in the

space above for reference.

Serial Number Decal (under seat)

Sears, Roebuck and Co., Hoffman Estates, IL 60179

· Assembly

· Adjustments

· Troubleshooting

· Part List and Drawing

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

CABLE DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

FULL 90 DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before

beginning assembly.

IMPORTANT PRECAUTIONS

1. Read all instructions in this manual and in

the accompanying literature before using the

weight system.

2. It is the responsibility of the owner to ensure

that all users of the weight system are ade-

quately informed of all precautions.

3. The weight system is intended for home use

only. Do not use the weight system in any

commercial, rental, or institutional setting.

4. Use the weight system only on a level sur-

face. Cover the floor beneath the weight sys-

tem to protect the floor.

5. Make sure that all parts are properly tight-

ened each time you use the weight system.

Replace any worn parts immediately.

6. Keep children under 12 and pets away from

the weight system at all times.

7. Keep hands and feet away from moving parts.

8. Always wear athletic shoes for foot protection.

9. The weight system is designed to support a

a maximum user weight of 300 pounds.

10. The weight system should not be used by

more than one person at a time.

11. Always stand on the foot plate when per-

forming an exercise that could cause the

weight system to tip.

12. Never release the butterfly arms, leg lever,

squat arm, lat bar, row bar, or handle while

weights are raised. The weights will fall with

great force.

13. Always disconnect the lat bar from the

weight system when performing an exercise

that does not use the lat bar.

14. Make sure that the cables remain on the pul-

leys at all times. If the cables bind while you

are exercising, stop immediately and make

sure that the cables are on all of the pulleys.

15. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

16. The warning decals shown here have been

placed on the weight system in the locations

shown on page 4. If a decal is missing or

illegible, please call our Customer Service

Department toll-free at 1-877-992-5999,

Monday through Friday, 6 a.m. until 6 p.m.

Mountain Time, to order a free replacement

decal. Place the decal on the weight system

in the location shown.

WARNING: To reduce the risk of serious injury, read the following important precautions

before using the weight system.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. Sears assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

Keep hands and

fingers clear of

this area.

Decal 2

Decal 1

BEFORE YOU BEGIN

ASSEMBLED

DIMENSIONS:

Height: 81 in.

Width: 96 in.

Length: 57 in.

Squat Knee Rest

Curl Pad

Low Pulley Station

High Pulley Station

Lat Bar

Swivel Carriage

Adjustment Knob

Butterfly Arm/Press Arm

Leg Lever

Seat

Squat Arm

Weight Stack

Backrest

WARNING

DECAL 1

WARNING DECAL 2

(one on each side)

WARNING

DECAL 2

Thank you for selecting the versatile WEIDER®PRO

4850 weight system. The WEIDER®PRO 4850 weight

system offers an impressive array of weight stations

designed to develop every major muscle group of the

body. Whether your goal is to tone your body, build

dramatic muscle size and strength, or improve your

cardiovascular system, the PRO 4850 weight system

will help you to achieve the specific results you want.

For your benefit, read this manual carefully before

using the weight system. If you have questions after

reading this manual, call 1-800-4-MY-HOME®

(1-800-469-4663). To help us assist you, please note

the product model number and serial number before

calling. The model number is 831.153932. The serial

number can be found on a decal attached to the

weight system (see the front cover of this manual for

the location of the decal).

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled.

ASSEMBLY

Make sure that you have the following tools:

• Two adjustable wrenches

• One standard screwdriver

• One phillips screwdriver

• One rubber mallet

• You will also need grease or petroleum jelly, a

small amount of soapy water, and masking tape.

Note: Assembly will be more convenient if you have

a socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

How to Identify Parts

To help you identify the small parts used in assembly,

a PART IDENTIFICATION CHART is included in the

center of this manual. Lay the chart on the floor and

use it to easily identify parts during each assembly

step. Note: Some small parts may have been pre-

attached. If a part is not in the parts bag, check

to see if it has been pre-attached.

How to Orient Parts

As you assemble the weight system, make sure that

all parts are oriented exactly as shown in the draw-

ings.

Tightening Parts

Tighten all parts as you assemble them, unless

instructed to do otherwise.

Questions?

If you have questions after reading the assembly

instructions, please call 1-800-4-MY-HOME®

(1-800-469-4663).

Assembly Requires Two Persons

For your convenience and safety, assemble the

weight system with the help of another person.

Set Aside Enough Time

Due to the many features of the weight system, the

assembly process will require several hours. By

setting aside plenty of time and by deciding to

make the task enjoyable, assembly will go smoothly.

Select a Location for the Weight System

Because of its weight and size, the weight system

should be assembled in the location where it will be

used. Make sure that there is enough room to walk

around the weight system as you assemble it.

How to Unpack the Box

To make assembly easier, we have divided the

assembly process into four stages. The small hard-

ware needed for each stage is packaged in sepa-

rate bags. Important: Wait until you begin each

stage to open the parts bag(s) for that stage.

Place all parts of the weight system in a cleared

area and remove the packing materials. Do not dis-

pose of the packing materials until assembly is com-

pleted.

Make Assembly Easier

Everything in this manual is designed to

ensure that the weight system can be assem-

bled successfully by anyone.

Before beginning assembly, make sure to

read the information on this page. This

brief introduction will save you much more

time than it takes to read it.

The Four Stages of the Assembly Process

Frame Assembly—You will begin by assembling

the base and the uprights that form the skeleton of

the weight system.

Arm Assembly—During this stage, you will

assemble the arms and the leg lever.

Cable Assembly—During this stage, you will

attach the cables and pulleys that connect the

weight stations to the weight stacks.

Seat Assembly—During the final stage, you will

assemble the seat and the backrests.

Locate and open the parts bags labeled “FRAME

ASSEMBLY 1” and “FRAME ASSEMBLY 2.”

See the inset drawing. Attach the Base Cap (24) to

the Short Base (2) with two M4 x 20mm Self-tapping

Screws (14) and two M4 Washer (98).

Press a 50mm Square Inner Cap (105) into the

open end of the Long Base (106).

Insert eight M10 x 65mm Carriage Bolts (110) up

through the Long Base (106) and the Short Base (2)

as shown. Note: It may be helpful to place tape

over the heads of the Carriage Bolts to hold

them in place.

Attach the Short Base (2) to the Long Base (106)

with two M10 x 70mm Bolts (85), the Long Frame

Plate (71), and two M10 Nylon Locknuts (87).

FRAME ASSEMBLY

Make sure that you understand all of the

information on page 5 before you begin

assembling the weight system.

105

106

287

2. Press two 50mm x 75mm Inner Caps (58) into the

Foot Plate (53). Attach the Foot Plate to the Long

Base (106) with two M10 x 65mm Carriage Bolts

(110) and two M10 Nylon Locknuts (87).

3. Attach the tether on the Pin w/Tether (112) to the

Long Base (106) with an M4 x 20mm Self-tapping

Screw (14).

Attach the four Knee Rest Bumpers (30) to the

Squat Knee Rest (41) with four M4 x 20mm Self-

tapping Screws (14).

Attach the Squat Knee Rest (41) to the Long Base

(106) with an M10 x 85mm Bolt (96) and an M10

Nylon Locknut (87). Do not overtighten the Nylon

Locknut; the Squat Knee Rest must be able to

pivot.

106

112

14 96 41

110

110 53

106

4. Press a 38mm Square Inner Cap (67) into the

square tube on the Butterfly Upright (3).

Slide the Butterfly Upright (3) onto the two indicated

M10 x 65mm Carriage Bolts (110) in the Short Base

(2). Finger tighten an M10 Nylon Locknut (87) onto

each Carriage Bolt. Do not tighten the Locknuts

yet.

5. Press a 50mm x 75mm Inner Cap (58) halfway into

the top of the Seat Upright (9); it will need to be

removed later. Attach the Leg Lever Bumper (77) to

the Seat Upright with an M4 x 20mm Self-tapping

Screw (14) and an M4 Washer (98).

Slide the Seat Upright (9) onto the two indicated

M10 x 65mm Carriage Bolts (110) in the Short Base

(2). Finger tighten an M10 Nylon Locknut (87) onto

each Carriage Bolt. Do not tighten the Locknuts

yet.

110

6. Hold the Seat Frame (8) between the Seat Upright

(9) and the Butterfly Upright (3). Attach the Seat

Frame to the Seat Upright with two M10 x 95mm

Bolts (92), two M10 Washers (91), and two M10

Nylon Locknuts (87). Do not tighten the Locknuts

yet.

Attach the Seat Frame (8) to the Butterfly Upright

(3) with two M10 x 95mm Bolts (92), two M10

Washers (91), and two M10 Nylon Locknuts (87).

Do not tighten the Locknuts yet.

7. Press a 50mm x 75mm Inner Cap (58) into the top

of the Squat Upright (4). Press two 25mm Round

Outer Caps (120) onto the Upright.

Slide the Squat Upright onto the two indicated M10

x 65mm Carriage Bolts (110) in the Long Base

(106). Finger tighten an M10 Nylon Locknut (87)

onto each Carriage Bolt. Do not tighten the

Locknuts yet.

Press a 50mm x 75mm Inner Cap (58) into the top

of the Swivel Upright (5). Slide the Swivel Upright

onto the two indicated M10 x 65mm Carriage Bolts

(110) in the Long Base (106). Finger tighten an M10

Nylon Locknut (87) onto each Carriage Bolt. Do not

tighten the Locknuts yet.

106

120

110

Adjustment

Hole

8. Press two Swivel Bushings (66) into the Swivel

Carriage (46).

Tighten an Adjustment Handle (65) into the Swivel

Carriage (46). Orient the Swivel Carriage as shown.

Slide the Carriage onto the Swivel Upright (5) and

engage the Adjustment Handle into an adjustment

hole in the Swivel Upright.

9. Attach a Roller (39) between the indicated set of

holes in the Squat Slider (38) with an M8 x 85mm

Bolt (94) and an M8 Nylon Locknut (86) as shown.

Do not overtighten the Locknut.

Assemble the other three Rollers (39) to the

Squat Slider (38) in the same manner.

10. Slide the Squat Slider (38) down onto the Squat

Upright (4).

11. Orient the Weight Guides (42) with the indicated

holes on top. Insert the ends of two Weight Guides

into the indicated bracket on the Long Base (106).

Slide two Weight Bumpers (49) onto the Weight

Guides. Next, slide ten Weights (44) onto the Weight

Guides. Make sure that the Weights are turned so

the grooved sides of the Weights are facing

downward.

Press a Weight Tube Bumper (48) into the lower

end of a Weight Tube (43). Insert the Weight Tube

into the centers of the Weights (44). Make sure

that the Weight Tube is turned as shown.

Lubricate the two outer holes in a Top Weight (45).

Slide the Top Weight onto the Weight Guides (42).

Make sure that the Top Weight is turned so the

grooved side is facing downward.

Apply a number “10” decal to the Top Weight (45) in

the location shown. Apply decals with the numbers

20 through 110 to the ten Weights (44).

Assemble the other weight stack in the same

way.

106

Groove

Lubricate

Holes

“10” Decal

“110” Decal

Holes

“20” Decal

14. Open the parts bag labeled “ARM ASSEMBLY.”

Press three 40mm x 50mm Inner Caps (21) into the

Leg Lever (10). Attach the Eyebolt (116) to the Leg

Lever with an M10 Washer (91) and an M10 Nylon

Locknut (87).

Lubricate an M10 x 65mm Bolt (59) with grease.

Turn the Leg Lever (10) so that the welded tab is

on the indicated side, and attach the Leg Lever to

the Seat Upright (9) with the Bolt and an M10 Nylon

Locknut (87). Do not overtighten the Locknut;

the Leg Lever must be able to pivot easily.

15. Press a 50mm x 70mm Inner Cap (34) into the

Butterfly Frame (47). Attach the tethers on the two

“L”-pins w/Tether (60) to the Butterfly Frame with an

M4 x 20mm Self-tapping Screw (14).

Lubricate a an M10 x 75mm Bolt (107) with grease.

Attach the Butterfly Frame (47) to the Butterfly Top

Frame (7) with the Bolt and an M10 Nylon Locknut

(87). Do not overtighten the Locknut; the

Butterfly Frame must be able to pivot easily.

ARM ASSEMBLY

13. Press two 50mm x 75mm Inner Caps (58) into the

Top Frame (6) and the Butterfly Top Frame (7).

Attach the Butterfly Top Frame (7) to the Top Frame

(6) with two M10 x 70mm Bolts (85), two M10

Washers (91), and two M10 Nylon Locknuts (87).

Do not tighten the Locknuts yet.

Attach the Butterfly Top Frame (7) to the Butterfly

Upright (3) with two M10 x 95mm Bolts (92), two

M10 Washers (91), and two M10 Nylon Locknuts

(87).

Tighten all of the M10 Nylon Locknuts (87) used

in steps 2–13.

116 91

Lubricate

Tab

87 107—Lubricate

12. Attach the Top Frame (6) between the Squat Upright

(4) and the Swivel Upright (5) with four M10 x 95mm

Bolts (92), the two Short Frame Plates (52), and two

M10 Nylon Locknuts (87) as shown. Do not tighten

the Bolts and Locknuts yet.

Attach the four Weight Guides (42) to the Top Frame

(6) with two M10 x 165mm Bolts (95), four M10

Washers (91), and two M10 Nylon Locknuts (87).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Gimnasio en casa de Weider

Weider

Weider Platinum Xp 800 Manual de usuario

Weider

Weider 190 Tc Bench Guía de inicio rápido

Weider

Weider 831.153931 Manual de usuario

Weider

Weider Precision 200 Manual de usuario

Weider

Weider Power Tower WEBE99712.0 Manual de usuario

Weider

Weider WESY8630C3 Manual de usuario

Weider

Weider Body Works Pro 2.0 Bench Guía de inicio rápido

Weider

Weider PRO 9400 Manual de usuario

Weider

Weider MEDALLION M139 Manual de usuario

Weider

Weider WEEVSY1975.0 Manual de usuario

Weider

Weider Pro 290 wc bench Guía de configuración

Weider

Weider XRS 20 Manual de usuario

Weider

Weider WB1750 Manual de usuario

Weider

Weider 240 Tc Bench Manual de usuario

Weider

Weider Tc 150 Bench Manual de operación y mantenimiento

Weider

Weider 831.150850 Manual de usuario

Weider

Weider 244 Bench Guía del usuario

Weider

Weider Muscle 1352 Bench Manual de usuario

Weider

Weider PRO 9645 Manual de usuario

Weider

Weider 9900i Guía de inicio rápido

Weider

Weider 195 Tc Bench Manual de operación y mantenimiento

Weider

Weider C103 Manual de usuario

Weider

Weider WEBE63990 Manual de usuario

Weider

Weider 9000 Bench Manual de usuario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

ParaBody

ParaBody 40 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario

Insportline

Insportline RW600 Manual de usuario

Stamina

Stamina 55-1532 Manual de usuario

Tunturi

Tunturi R25 Manual de usuario