Weider Platinum Plus WESY7974.0 Manual de usuario

Model No. WESY7974.O

Serial No.

Write the serial number in the

space above for future reference,

Serial Number Decal (under seat)

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if a part is

damaged or missing, PLEASE

CONTACT OUR CUSTOMER

SERVICE DEPARTMENT

DIRECTLY.

CALLTOLL-FREE:

1-877-992-5999

Mon.-Fri., 6 a.m.-6 p.m. MST

ON THE WEB:

www.weiderservice.com

USER'S MANUAL

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

WARNING DECAL PLACEMENT ............................................................. 3

IMPORTANT PRECAUTIONS ................................................................ 4

BEFORE YOU BEGIN ...................................................................... 5

ASSEMBLY ............................................................................... 6

ADJUSTMENTS .......................................................................... 16

CONSOLE OPERATION .................................................................... 20

TROUBLESHOOTING ..................................................................... 22

EXERCISE GUIDELINES .................................................................. 23

ORDERING REPLACEMENT PARTS .................................................. Back Cover

LIMITED WARRANTY .............................................................. Back Cover

Note: A PART IDENTIFICATION CHART and aPART LIST/EXPLODED DRAWING are attached in the center of

this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-

ning assembly.

WELDER is a registered trademark of ICON IF',Inc.

WARNING DECAL PLACEMENT

The decals shown here have been

placed on the resistance system. If a

decal is missing or illegible, call the

toll-free telephone number on the front

cover of this manual and order a free

replacement decal. Apply the decal in

the location shown.

hands and

clear of

area.

• Misuse of this machine

may result in serious

injury.

• Read user's manual

prior to use and follow

all warnings and

instructions.

• Do not allow children

on or around machine.

• Keep body, clothing,

and hair free and clear

of all moving parts.

• Replace label if

damaged, illegible, or

removed.

IMPORTANT PRECAUTIONS

BEFORE YOU BEGIN

Thank you for selecting the innovative PLATINUM

PLUS BY WELDER®resistance system. The resistance

system offers a selection of stations designed to devel-

op every major muscle group of the body. Whether your

goal is to tone your body, build dramatic muscle size

and strength, or improve your cardiovascular system,

the resistance system will help you to achieve the spe-

cific results you want.

For your benefit, read this manual carefully before

using the resistance system, If you have questions

after reading this manual, see the front cover of this

manual. To help us assist you, please note the product

model number and serial number before calling. The

model number is WESY7974.0. The serial number can

be found on a decal attached to the resistance system

(see the front cover of this manual).

To avoid a registration fee for any service needed

under warranty, you must register the resistance

system at www.weiderservice.com/registration.

Before reading further, please review the drawing below

and familiarize yourself with the parts that are labeled.

Top Frame

High Pulley

Handle

Console

Squat Backrest Squat Arm

Squat Pin

Backrest

Curl Pad

Curl

Leg Lever

Storage Knob

Low Pulley

Seat

Seat Knob

Base Plate

ASSEMBLED DIMENSIONS:

Height: 85 in. /216 cm

Width: 47 in. /!19 cm

Depth: 94 in. /239 cm

ASSEMBLY

• Tighten all parts as you assemble them, unless

instructed to do otherwise.

Before beginning assembly, carefully read the

following information and instructions:

• Assembly requires two persons.

• Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until assembly is completed.

•For help identifying small parts, use the PART

IDENTIFICATION CHART. Note: Some small

parts may have been pre-attached for shipping. If

a part is not in the parts bag, check to see if it

has been pre-attached.

• As you assemble the resistance system, make

sure all parts are oriented as shown in the draw-

ings. E

The included hex keys Wand the following

tools (not included) are required for assembly:

•Two adjustable wrenches

•One rubber mallet

•One standard screwdriver

•One Phillips screwdriver

•Lubricant, such as grease or petroleum jelly,

tape, and soapy water.

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end

wrenches, or a set of ratchet wrenches.

Attach four Plastic Base Feet (71) to the Base (1)

with four M4 Washers (157) and four M4 x 16mm

Self-tapping Screws (104).

Attach a Wheel (49) to the Base (1) with an M8 x

90mm Shoulder Bolt (125), two M8 Washers

(152), and an M8 Nylon Jamnut (139). Repeat

with the other Wheel.

152

_71

_ 157 104

104 _'71

\157

104

Insert two M10 x 65mm Carriage Bolts (103) up

through the Base (1). Place a piece of tape over

the Bolt heads to hold them in place. Connect

the Upright Base (2) to the Base with the two

Carriage Bolts and two M10 Nylon Locknuts

(!12). Do not tighten these Locknuts yet.

Connect the Upright Base (2) to the Base (1) with

two M10 x 67mm Bolts (111) and two M10 Nylon

Locknuts (112). Fully tighten these Locknuts.

Set the Mech Frame (!24) onto the Base (1)

behind the Upright Base. Handtighten two M10 x

73mm Screws (137) and two M10 Washers (129)

into the indicated holes in the Base and Mech

Frame, Note: The Mech Frame will not be

shown in the following drawings for clarity.

Note: One end of the Rope (70) is connected

to the Right Arm Frame (17t). Untie the loose

end of the Rope and route it through the Upright

Base (2). Make sure the loose end of the Rope

is still between the 90ram Thin Pulley (88) and

Cable Trap (78) (see the inset drawing), and

that it crosses under the connected end of the

Rope.

Insert two M14 x 155mm Bolts (107) through the

Right Arm Frame (171) and the Upright Base (2).

Hand tighten two M!4 Nylon Locknuts (!27) onto

the Bolts,

Route the loose end of the Rope (70) through the

Left Arm Frame (8) and a Swivel Arm (29). Make

sure the Rope is under the indicated rod in the

Swivel Arm.

Attach the Swivel Arm (29) to the Left Arm Frame

(8) with an M4 x 5mm Self-tapping Screw (!76).

Attach a "V"-pulley (93) inside the Swivel Arm

(29) with an M10 x 53mm Button Bolt (140) and

an M10 Nylon Locknut (112),

Route the loose end of the Rope (70) through a

Rope Cover (169) and a Link (167) as shown.

Make sure the large hole in the Rope Cover is

on the side shown. Secure the set of Rope

Clamps (165, 166) on the Rope with two M5 x

16mm Button Screws (164), Make sure that

Rope is in the grooves of the Rope Clamps,

that there is t/2" between the Link and the

Rope Clamps, and that the two Screws are fully

tightened. Slide the Rope Cover over the Rope

Clamps,

f"--. ,1/07 2\/4.,_ 4/ _ /

_27

___ 137

129

78 88

---T--T_

- _--o Z_ 93"

4164

70 169 _i

Hole 166 67

Remove the two M14 Nylon Locknuts (127).

Attach the Left Arm Frame (8) to the Upright Base

(2) with the two M14 x 155mm Bolts (107) used in

step 2 and the two M14 Nylon Locknuts,

Attach the Backing Plate (59) to the Upright Base

(2) with two M!0 x 65mm Carriage Bolts (103)

and two M10 Nylon Lecknuts (112), Do not tight-

en the Locknuts yet.

Attach the Squat Backrest (28) to the Squat

Carriage (!0) with four M6 x !6mm Screws (108), 7

103

107

59\

127

108

8. 8

Slide the Squat Carriage (10) onto the Upright (3)

as shown. Insert the Squat Pin (35) into an upper

hole in the Upright.

Press the Front Cover (3!) onto the Upright Base

(2). Make sure the Cover is oriented as shown

in the inset drawing.

Route the Upper Wire Harness (172) down

through the Upright Base (2) and out the large

round hole in the back, as shown.

Slide the Upright (3) onto the Upright Base (2).

Make sure you do not pinch the Upper Wire

Harnesses (t72). Secure the Upright with two

M!0 Washers (129), two M10 x 20mm Screws

(113), and two M10 x 25ram Screws (105). Do

not tighten the Screws yet.

Connect the Upper Wire Harness (172) to the

Lower Wire Harness (173) extending from the

Mech Frame (not shown). The connector should

slide easily into the socket and snap into place.

If the connector does not slide easily and snap into

place, turn it over and then insert it. IF THE CON-

NECTOR IS NOT INSERTED PROPERLY, THE

CONSOLE MAY BE DAMAGED WHEN THE

POWER IS TURNED ON. Press the excess wire

into the Upright Base.

Tighten two M4 x !6mm White ZP Self-tapping

Screws (159) into the Upright (3).

159

113

173

172

10. Insert an M1O x 125mm Button Screw (144)

through an M!O Washer (!29), the Upright (3),

and the Backing Plate (not shown). Bold the Bolt

in place by sticking a piece of tape over the

bolt head.

Tighten the two Mt0 Nylon Locknuts (1t2)

used in step 6. Tighten the two Mt0 x 20ram

Screws (tt3) and two Mt0 x 25ram Screws

(t05) used in step 9.

Attach the Mech Frame (124) to the Base (1) with

two M10 x 73ram Bolts (137) and two M1O

Washers (129), Do not tighten the Bolts yet.

Attach the Mech Frame (124) to the Upright (3)

with the M10 x 125mm Button Screw (144). Make

sure the Upright and Mech Frame are properly

aligned before tighten the Screw.

Tighten the four M10 x 73ram Bolts (137) in

the Base (1) and the two Mt0 Nylon Locknuts

(tt2) used in the first paragraph of step 2.

Snap the Side Mech Cover (81) into place on the

Mech Covers (14 and 15).

11. Wet a Squat Arm (18) and the inside of a Small

Foam Pad (36) with soapy water. Slide the Foam

Pad onto the Squat Arm.

Grease an M10 x 73mm Bolt (137). Attach a

Squat Arm (18) to the Squat Carriage (!0) with

the Bolt, two 24mm Plastic Washers (110), and

an M1O Nylon Locknut (112). Do not overtighten

the Locknut; the Squat Arm should be able to

pivot with intermediate effort.

Repeat this step with the other Squat Arm

(18).

12. Orient the Top Frame (20) with the mark in the

position shown. Attach the Top Frame to the

Upright (3) with two M10 x 65mm Button Screws

(!17) and two M10 Washers (129). Press the

Plastic Cap (46) into the Upright, over the Top

Frame.

129

144

124

137

Grease_

112

20 Mark 3

117 129

"1 129_ 137

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Gimnasio en casa de Weider

Weider

Weider Black 150 Xwb Bench Manual de usuario

Weider

Weider 831.159830 Manual de usuario

Weider

Weider Body Works Manual de usuario

Weider

Weider WESY3873.2 Manual de usuario

Weider

Weider WESY39522 Manual de usuario

Weider

Weider Pro 137 Bench Manual de usuario

Weider

Weider PRO PC3 WEBE63990 Manual de usuario

Weider

Weider 390 Lt Bench Manual de usuario

Weider

Weider Power glide WCCR44060 Manual de usuario

Weider

Weider 8700 I Manual del sistema

Weider

Weider 9900i Guía de configuración

Weider

Weider 9250 Manual de usuario

Weider

Weider WEEVSY87210 Manual de usuario

Weider

Weider XP400 831.15392.2 Manual de usuario

Weider

Weider Cross Bow Advantage 831.153960 Manual de usuario

Weider

Weider 138 Manual de usuario

Weider

Weider 9940 Manual de usuario

Weider

Weider 340 Lc Bench Manual de usuario

Weider

Weider 831.153921 Manual de usuario

Weider

Weider C120 Manual de usuario

Weider

Weider E475 Home Gym Manual de usuario

Weider

Weider PRO POWER STACK 831.159831 Manual de usuario

Weider

Weider Pro 2000 Manual de operación y mantenimiento

Weider

Weider 224 Bench Manual de usuario

Manuales populares de Gimnasio en casa de otras marcas

Horizon Fitness

Horizon Fitness OXFORD 6 Manual de usuario

Energetics

Energetics Multi Trainer 5.1 Manual de usuario

Matrix

Matrix MG-PL Series Manual de usuario

Reebok

Reebok Tbr2i Manual de operación y mantenimiento

Pure Fitness

Pure Fitness 8526HE Manual de usuario

Bowflex

Bowflex Sport 001-6961 Manual de usuario

NordicTrack

NordicTrack E8200 Competition Bench Guía de inicio rápido

Body Solid

Body Solid GHYP-345 Manual de usuario

Evo

Evo TAHOE 5105 Manual de usuario

cardiobull

cardiobull RA17 Manual de usuario

ParaBody

ParaBody 40 Manual de usuario

JLL

JLL Ventus Pro Air Power Manual de usuario

Trojan

Trojan Colorado 370 Manual de usuario

Octane Fitness

Octane Fitness xRide xR650 Manual de usuario

Precor

Precor Discovery Series Manual de usuario

Insportline

Insportline RW600 Manual de usuario

Stamina

Stamina 55-1532 Manual de usuario

Tunturi

Tunturi R25 Manual de usuario