WebGate C1080PT-Z20 Manual de usuario
Ver. 1.0
User’s Manual
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
x20 HD-SDI PTZ
CAMERA (C1080PT-Z20)
Safety Information
2
This symbol indicates that dangerous voltage
consisting a risk of electric shock is present within
this unit.
Warning Precaution
This exclamation point symbol is intended to alert the
user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
To prevent damage which may result in re or electric shock
hazard, do not expose this appliance to rain or moisture.
WARNING
Be sure to use only the standard adapter that is specied in
the specication sheet. Using any other adapter could cause
re, electrical shock, or damage to the product.
Incorrectly connecting the power supply or replacing battery
may cause explosion, re, electric shock, or damage to the
product.
Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause excessive heat generation
or re.
Securely plug the power cord into the power receptacle.
Insecure connection may cause re.
When installing the camera, fasten it securely and rmly.
A falling camera may cause personal injury.
Do not place conductive objects (e.g. screw drivers, coins,
metal items, etc.) or containers lled with water on top of
the camera. Doing so may cause personal injury due to re,
electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause re or electric shock.
If any unusual smells or smoke come from the unit, stop
using the product. Immediately disconnect the power sorce
and contact the service center. Continued use in such a
condition may cause re or electric shock.
If this product fails to operate normally, contact the nearest
service center. Never disassemble or modify this product in
any way.
When cleaning, do not spray water directly onto parts of the
product. Doing so may cause re or electric shock.
WARNING
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Precaution
Operating
t Before using, make sure power supply and all other parts are
properly connected.
tWhile operating, if any abnormal condition or malfunction
is observed, stop using the camera immediately and contact
your dealer.
Handling
tDo not disassemble or tamper with parts inside the camera.
tDo not drop the camera or subject it to shock or vibration as
this can damage the camera.
tClean the clear dome cover with extra care. Scratches and
dust can ruin the quality of the camera image.
Installation and Storage
tDo not install the camera in areas of extreme temperature,
exceeding the allowed range.
tAvoid installing in humid or dusty environments.
tAvoid installing in places where radiation is present.
tAvoid installing in places where there are strong magnetic
elds and electric signals.
tAvoid installing in places where the camera would be subject
to strong vibrations.
tNever expose the camera to rain or water.
3
Important Safety Instructions
1. Read these instructions. - All these safety and operating instructions should be read before the product is
installed or operated.
2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instructions should be followed.
5. Do not use this device near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet
basement; near a swimming pool; etc.
6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and
openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it
from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar
surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and the manufacturer’s unstructions have been adhere to.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampliers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
4
Disposal of Old Appliances
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the municipal waste
stream stream in accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for
the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city oce,
waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interferenece at his own expense.
Contents
5
6
7
8
9
14
16
18
19
20
21
22
23
24
25
26
27
28
30
31
32
33
34
35
36
Product & Accessories
Parts Name & Functions_Appearance
Parts Name & Functions_Inside
Installation
DIP Switch Setup
Cabling
Check Points before Operation
OSD Information
General Rules of Menu Operation
ROOT MENU & SYSTEM INFORMATION
DISPLAY SETUP
MOTION SETUP > ALARM INPUT SETUP
MOTION SETUP > PARKING ACTION SETUP
FUNCTION SETUP > PRESET SETUP
FUNCTION SETUP > SCAN SETUP
FUNCTION SETUP > PATTERN SETUP
FUNCTION SETUP > GROUP SETUP
CAMERA SETUP > WHITE BALANCE SETUP
CAMERA SETUP > AUTO EXPOSURE SETUP
CAMERA SETUP > OTHER SETUP
CAMERA SETUP > PRIVACY ZONE SETUP
SYSTEM SETUP
Dimension
Specification
4 Precautions
1. Introduction
2. Installation
3. OSD Menu
4. Specifications
6
Product & Accessories
Introduction -
1
Product Accessories
Wall Mount Type
Ceiling Mount Type
Housing Safety
Cable Hanger
Waterproof Tape
Mount Template Sheet
Hexagonal Wrench
Manual CD
Anchor Bolt(4pcs)
Safety Wire
102.0
142.0
Quick Manual
Please check if all the camera and accessories are included in the package.
7
Part Name & Functions_Appearance
Introduction -
1
1
1
2
2
3
5
3
4
5
Wall/Ceiling Mount Bracket
These are used to install the camera on the wall or ceiling
and have junction box.
Sunshield &
Upper Housing
4Dome Safety Wire
PTZ Mechanism
Dome Cover
Housing Safety
Wire Hanger
Wall Mount Bracket
Ceiling Mount Bracket
Sunshield & Upper Housing
Sunshield protect bubble dome cover from the sun rays and
rain fall. In the sunshield, there is the upper housing which
will contain accommodate PTZ mechanism. In the upper
housing, there are fan and heater to remove moisture on
the bubble dome. Also, the upper housing will be
connected to both mounting brackets and dome cover.
PTZ Mechanism
Control the PTZ operations of the camera.
Dome Safety Wire
Prevents the dome cover from falling.
Dome Cover
Do not detach protection lm from dome cover before
nishing all installation process to protect dome cover from
scratches or dust.
8
Part Name & Functions_Inside
Introduction -
1
6
7
8
9
10
Test Video Output Connector
Video out check the screen during installation.
DIP Switch for Camera ID Setup
Specify the camera ID.
DIP Switch for Communication Setup
Set the transfer rate and protocols.
RS-485 Slot
Used for RS-485 communications.
Power Slot
Connect the power source here.
1
2
3
4
5
Video Output Cable
Connects to video output device such as monitor using the
BNC coaxial cable.
Alarm Output Slot
It connects to the alarm lights, siren or lamps, and it is
activated according to the OSD menu or ‘Setup’ on the Web
-viewer setting.
Alarm Input Slot
It connects to IR sensor, IrDA sensor or door switch. If the
sensor is activated, it can activate to move camera to the
specic angle and to connect the alarm device.
Fan
Defrosts the dome cover and removes moisture.
Heater
Defrost the dome cover in a low temperature by increasing
the internal temperature of the housing.
Alarm Output Slot
Alarm Input Slot
Fan
Heater
DIP Switch for
Camera ID Setup
DIP Switch for
Communication
Setup
RS-485 Slot
Power Slot
Test Video
Output Connector
2
3
4
5
6
7
1
Video Output Cable
8
10
9
9
Installation -
Installation Using Wall/Ceiling Mount Bracket
2
2
1
3
Using the mount template sheet, mark the holes on the
wall or ceiling.
After drilling the holes, x the four anchor bolts into the
holes.
Place the wall/ceiling mount bracket on the anchor bolts
properly and tighten the nuts on the anchor bolts.
Ceiling Mount Bracket
Installation
Wall Mount Bracket
Installation
10
Installation
Installation -
2
4Detach the PTZ mechanism from the upper housing to plug
the main cable. When detaching the PTZ mechanism, press
down and hold up the black handles on both sides of the
PTZ mechanism.
Remove the protecting tape used to fix the PTZ
mechanism.
5[1] Wind the waterproof tape around the pipe of housing.
[2] Hook the safety wire on the hole of pipe and the housing
safety cable hanger.
[3] Attach the upper housing to wall mount bracket by
turning it at least seven turns.
To secure the orientation of the housing, turn the ring
cap counter-clockwise until it is tight.
[2]
[1]
[3]
Tabla de contenidos
Otros manuales de Cámara de seguridad de WebGate
WebGate
WebGate K1080D-lR30 Manual de usuario
WebGate
WebGate C1080Bullet Series Manual de usuario
WebGate
WebGate C1080PBL-IR48-AF Manual de usuario
WebGate
WebGate C1080Bullet Series Manual de usuario
WebGate
WebGate C1008Dome Series Manual de usuario
WebGate
WebGate C1080PD-F1 Manual de usuario
WebGate
WebGate C1080BL-IR48-AF Manual de usuario
WebGate
WebGate C1080PBM Manual de usuario
WebGate
WebGate K1080H-IR100-F3.6S Manual de usuario
WebGate
WebGate C1080PBL-IR48-AF Manual de usuario
