Webasto Thermo Top E Manual de usuario
Water Heater Unit
Installation Instructions
Ident. No.:1315210A_EN Fee Euro 10.00 © Webasto AG
Peugeot 3008
Diesel
from Model Year 2009
Left-hand drive vehicle
Manual transmission
Automatic air-conditioning
Feel the drive
WARNING!
Hazard warning:
Incorrect installation or repair of Webasto heating systems may cause a fire or result in the
emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as
a result.
Specialist company training, technical documentation, specialized tools and equipment are
required to install and repair Webasto heating and cooling systems.
Only genuine Webasto parts may be used. See also Webasto air and water heaters acces-
sories catalogue.
NEVER attempt to install or repair Webasto heating or cooling systems if you have not
successfully completed the company training and thereby acquired the required tech-
nical skills, or if you do not have access to the required technical documentation, tools
and equipment needed to carry out correct installation and repairs.
ALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Webasto does not accept any liability for defects and damage that are attributable to installa-
tion by untrained staff.
Thermo Top E Additional Heater e1
00 0003
Thermo Top C
Additional Heater
e1
00 0002
Thermo Top P Additional Heater e1
00 0104
Peugeot 3008
1315210A_EN 2
Table of Contents
Validity
Vehicle and engine types, equipment variants and national specifications not listed in these installation
instructionshavenotbeentested.However,installation according to these installationinstructions may
be possible.
The installation location of the digital timer should be confirmed with the end customer before installa-
tion.
Manufacturer Model Type EG-BE No./ABE
Peugeot 3008 OU e2 * 2001 / 116 * 0377 * ...
Engine type Engine model Output in kW Displacement in cm³
RHE Diesel 110 1997
Validity 2
Heater Unit/Installation Kit 3
Foreword 3
General Instructions 3
Special Tools 3
Explanatory Notes on Document 4
Preliminary Work 5
Heater unit installation location 5
Preparing electrical system 6
Electrical system 7
Fan controller 8
Remote option (Telestart) 10
Preparing installation location 11
Installing heater unit 12
Coolant circuit 13
Fuel 17
Combustion air 20
Exhaust gas 21
Final Work 23
Coding BSI Central switching unit 23
Operating Instructions for End Customer 24
Peugeot 3008
1315210A_EN 3
Heater Unit/Installation Kit
Heater unit recommended for the respective vehicle class:
The selection of the heater unit is based on the passenger compartment size of the vehicle and the
level of comfort required by the customer!
Foreword
These installation instructions apply to Peugeot 3008 Diesel vehicles - for validity, see page 2 - from
model year 2009 and later, assuming technical modifications to the vehicle do not affect installation,
any liability claims excluded. Depending on the vehicle version and equipment, modifications may be
necessary during installation with respect to these installation instructions.
However,thestipulations in the "installationinstructions"and"operating and maintenanceinstructions"
for the Thermo Top C/P/E must always be observed.
The corresponding rules of technology and any information from the vehicle manufacturer should be
observed during the installation work.
General Instructions
Installation should be carried out according to the general, standard rules of technology. Unless spec-
ified otherwise, fasten hoses, lines and wiring harnesses to original vehicle lines and wiring harnesses
using cable ties.
Sharp edges must be provided with rub protection (cut-open fuel hose)!
Spray unfinished body areas, e.g. drilled holes, with anti-corrosion wax (Tectyl 100K, Order No.
111329).
Special Tools
- Torque wrench for 2.0 - 10 Nm
- Hose clamping pliers
- Metric thread-setter kit
Quantity Description Order No.:
1 Retail accessories Thermo Top E / C / P See price list
1 Installation kit for Peugeot 3008 2009 Diesel 1315209A
1 Heater control See price list
Vehicle Heater Unit
Compact car Thermo Top E
Mid-size car, station wagon Thermo Top C
Full-size car, van, offroader Thermo Top P
Peugeot 3008
1315210A_EN 4
Special features are highlighted using the following symbols:
The arrow in the vehicle icon indicates the position on
the vehicle and the viewing angle.
Specific risk of injury or fatal accidents.
Specific risk of damage to components.
Specific risk of fire or explosion.
ReferencetogeneralinstallationinstructionsofWebas-
tocomponentsortothemanufacturer'svehicle-specific
documents.
Reference to a special technical feature.
All dimensions are in mm!
Tightening torque of hose clamps = 2.0 + 0.5 Nm!
Tightening torque of Ejot screws, Ejot studs = 10 Nm!
Mechanical system
Electrical system
Coolant circuit
Fuel
Exhaust gas
Combustion air
Software
Explanatory Notes on Document
To provide you with a quick overview of the individual working steps, you will find an identification mark
on the outside top right corner of the page in question.
Peugeot 3008
1315210A_EN 5
Preliminary Work
WARNING!
- Disconnect the battery "earth" or "ground" connection.
- Depressurize the cooling system.
- Copy the factory number from the original type label to the duplicate type label.
- Remove years that do not apply from the duplicate label.
- Attach the duplicate label (type label) in the appropriate place.
- Open the fuel tank cap and vent the fuel tank.
- Close the tank cap again.
- Remove engine design cover
- Remove air filter box
- Remove charge-air tube with bracket (bolts will be reused)
- Completely remove the battery and the battery carrier.
- Remove front underride protection
- Remove the right rear underride protection.
Remove page 24 "Operating Instructions for End Customer" and add to vehicle operating instructions!
Heater unit installation location
1Heater unit
Installa-
tion loca-
tion
1
1
Peugeot 3008
1315210A_EN 6
Preparing electrical system
Cut off black (sw) wire 5(0.75 mm²) from wir-
ing harness of heater unit. Cut off red/white
(rt/ws) wire 6(4 mm²) of fuse F3. Remove in-
sulation from ground wires to node point and
cut off brown (br) wire 4(0.75 mm²) from wir-
ing harness of digital timer.
Remove red/white (rt/ws) wire 1(4mm²) from
K3/87, red (rt) wire 3(4 mm²) from K3/87a
and black (sw) wire 2(4 mm²) from K3/30.
Preparing
fuse F3
and K3 re-
lay
Insulateandtie back ends of red/white(rt/ws)
wire 5and black (sw) wire 4. Insulate ground
wires 3.
Insert brown (br) wire 2(0.75 mm²) from wir-
ing harness of heater controls in K3/30.
Also connect black (sw) wire 1to K3/85 and
to K3/87.
Preparing
K3 relay
Stripinsulationfromapprox.500mmofwiring
harnessofdigitaltimer 3. Detach0.75² brown
(br) wire 1from wiring harness, crimp on mi-
crotimer and then re-insulate remaining
wires! Preparing
wiring har-
ness of
digital tim-
er
3
6
1
2
5
2
4
1
43
3
5
2
4
1
3
2
Peugeot 3008
1315210A_EN 7
Electrical system
Positive and ground wire
1Positive red (rt) wire on original vehicle posi-
tive support point
2Brown (br) ground wire on original vehicle
ground support point
Digital timer
1Digital timer
Wiring har-
ness in-
stallation
diagram
Fuse holder, K3 relay
1Retaining plate for fuse holder
24 mm dia. hole, 5.5x13 self-tapping screw;
plastic nut [2x each]
3K3 relay
4Fuse holder
Wiring harness pass through
Route wiring harnesses (digital timer, fan control-
ler and green/white (gn/ws) wire in protective
sleeving) on original vehicle wiring harness 1 to
protective rubber plug 2and route into passen-
ger compartment.
5
1
2
6
1
Do not install themetering pump
cableharnessuntillatertogether
with fuel pipe along the original
vehicle fuel lines on the under-
body
7
4
1 2
3
2
8
1
2
Peugeot 3008
1315210A_EN 8
Fan controller
Wiring dia-
gram
Webasto components Vehicle components Colors and symbols
Legend
HG Heater unit TT-C/E BSI Central electrical
box for passenger
compartment
gn green
K3 Fan relay ws white
1
Wiring harness of digital timer
St A 20-pin connector
BSI rt red
2Heater control connector br brown
sw black
Insulate wire ends and tie
back
Cable and connector colors may vary!
View of BSI.
1Socket for 2-piece connector. 40-pin
Detaching
BSI and
routing
downward
Webasto
31
30
15
Peugeot
0,5²
br
0,75²
br
0,75²
!
gn/ws
br
rt/
ws
sw
BSI
6St A
86
85 30
87a87
K3
1
HG
X1 4
2
9
1
1
Peugeot 3008
1315210A_EN 9
Press in locking lug 1and fold down bar 3.
220-pin blue connector
Pulling
connector
off BSI and
removing
Connection on 20-pin blue (bl) connector 2
from BSI. Insert microtimer from brown (br)
wire 1in PIN 6. Complete BSI connector and
mount.
Route wiring harness of digital timer upward
to installation location of digital timer.
Produce connections as shown in wiring dia-
gram.
Connec-
tion of BSI
10
1
2
3
11
2
1
Peugeot 3008
1315210A_EN 10
Remote option (Telestart)
Fasten receiver 2with adhesive tape onto
cross member 1!
Installing
receiver
1Antenna
Installing
antenna
Temperature sensor for HTM100 only
1Fasten temperature sensor with adhesive
tape
Installing
tempera-
ture sensor
12
1 2
13
1
1
14
Otros manuales para Thermo Top E
42
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Calentador de agua de Webasto
Webasto
Webasto thermo top evo Manual de instrucciones
Webasto
Webasto Thermo 90 Manual de instrucciones
Webasto
Webasto Thermo Top C Manual de usuario
Webasto
Webasto Mazda 3 MPS Manual de usuario
Webasto
Webasto Thermo Top C Manual de usuario
Webasto
Webasto Thermo 90 Manual de usuario
Webasto
Webasto Thermo Top E Manual del operador
Webasto
Webasto thermotop C Manual de usuario
Webasto
Webasto Thermo Pro 50 Eco Manual de instrucciones
Webasto
Webasto thermo top evo Manual del operador
Webasto
Webasto Thermo 50 Manual de usuario
Webasto
Webasto DBW 2010 Manual de instalación y funcionamiento
Webasto
Webasto Mazda 6 Manual de usuario
Webasto
Webasto DBW 2010 Manual del propietario
Webasto
Webasto Thermo Top C-B Manual de usuario
Webasto
Webasto Thermo 50 Manual de usuario
Webasto
Webasto Thermo Top E Manual de usuario
Webasto
Webasto Thermo Top E Manual de usuario
Webasto
Webasto Thermo Pro 90 Manual de instrucciones
Webasto
Webasto Thermo Top C Manual de usuario
