Weather Guard 238 Manual de instrucciones
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Conduit Carrier 6" Extension - Model 238
BOLT KIT
Bolt Kit #32-0236 is provided with
your extension. Check this bolt kit
to be sure the following parts are
included:
Quan. Description
10 1/4-20 x 3/4" Hex Hd. Bolt
20 1/4" Flat Washer
10 1/4-20 Nylon Lock Nut
WARNING
This product is only intended for, and only safe for, transporting
tubing, pipe and conduit. It is the responsibility of the user to
secure these materials to the rack before transporting. Any mod-
ifications made to this product, or use of this product for any
other purpose than its intended use, could create a hazardous
condition that can cause serious personal injury or property
damage.
Part No. 24-2380 REV. B ECN 5315 05/13
TOOLS REQUIRED
•7/16" Open or Box End Wrench (2)
•Razor knife or scissors
PARTS LIST
•Conduit Carrier Extension
•Weatherstripping (bulk)
IMPORTANT
BEFORE YOU BEGIN
Read these instructions and
warnings completely before
installation.
1
If you have any questions, please give us a call.Call Toll Free 1-800-456-7865
WeatherGuard®productsareprotectedbyoneormoreofthefollowingpatentsortrademarks:
U.S.-842268,1661625,1663369;Canada-282725;U.K.-1400720;otherpatentspending.
KNAACKLLC
420 E. TERRA COTTA AVENUE - CRYSTAL LAKE, ILLINOIS, 60014 - 815-459-6020
©1991KnaackLLC
-NOTICE-
Any modification or unintended use of this product shall immediately void all manufacturers warranties.
Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to, or
unintended use of this product.
INSTALLATIONINSTRUCTIONS
If installing this extension accessory on
a newly purchased Model 237 Conduit
Carrier, go directly to step A.
1. Loosen the front hold down strap on
your 237 Conduit Carrier where it fas-
tensontothecrossmember.
2. Support both front and rear conduit
carrier sections where they will part.
Removenutsandboltsholdingthetwo
halves and set them aside for reuse
later.
3. Cut sealing gaskets from Bulk
Weatherstrippingandattach to exten-
sion end. One carrier end should al-
ready have weatherstrip in place.
4. Insert extension between carrier
halvesandreinstallpreviouslyremoved
nutsandbolts.
5. Slide front half of carrier back to
meetfront of extensionand bolt to-
gether.
6. Refasten front carrier hold down
strap and your job is complete.
A. When adding this extension to your
conduit carrier during initial assembly,
insert between the front and rear
halves and fasten during Step 6 of the
Model237 instructionsheet.
Note - It is normal for the product to
get a dull gray color due to oxida-
tion.
1/4-20 x 3/4"
HexHd.Bolt
1/4"Flat
Washer
Extension
Weatherstrip
1/4-20
Nut
1/4"Flat
Washer
Part No. 24-2380 REV. B ECN 5315 05/13
2
Otros manuales de Accesorios para automóviles de Weather Guard
Weather Guard
Weather Guard 237 Manual de instrucciones
Weather Guard
Weather Guard PowerSync Manual de usuario
Weather Guard
Weather Guard 9444-3-01 Manual de usuario
Weather Guard
Weather Guard 96111-3-02 Manual de usuario
Weather Guard
Weather Guard ASRC001 Manual de usuario
Weather Guard
Weather Guard 1345-52-02 Manual de usuario
Weather Guard
Weather Guard 1175 02 Series Manual de usuario
Weather Guard
Weather Guard 234-3-01 Manual de usuario
Weather Guard
Weather Guard ITEMIZER 314 Manual de instrucciones
