Wattsense HUB Manual de usuario
HUB
Installation Guide
Intuitive IoT gateway
2021-08- 1.3
Made in France
Table of Contents
What do you need before starting? 2
Provided material 2
Required material 3
Optional hardware depending on the type of connection 3
Hub configuration software 3
The power supply of the Hub 4
To connect the Hub to the BMS 9
In case of IP network (Except LON) 10
In case of LON IP-852 network 12
In case of LON FT10 network 14
To connect the Hub directly to the technical equipment in the absence of a BMS 15
The equipment communicates in Modbus IP 16
The equipment communicates in Modbus RTU (RS485) 20
The equipment communicates in BACnet IP 24
The equipment communicates in LON FT10 27
The equipment communicates in LON IP-852 29
The equipment communicates in LPB 31
The equipment communicates in KNX 32
The equipment communicates in M-BUS 33
To connect the Hub to LoRaWAN sensors 34
GSM Antenna 35
2021-08-V1.3 1
What do you need before starting?
Provided material
● Hub
○ Dimensions: 160 x 110 x 55 mm
○ Weight: 340 g
● GSM standard antenna
● LoRa standard antenna
● USb to USB micro cable
2021-08-V1.3 2
Required material
● Powerline voltage (100 to 250VAC) to 12-24V DC +/-10%, 2A Max. Power supply
● Cable between the power supply and the Hub: 2 wires (red, black), 22 AWG,
minimum section: 0.35 mm²
● Flat screwdriver
● Cutting pliers
● Wire stripper
Optional hardware depending on the type of connection
● Bus connection cable: 2 wires, 24 AWG, minimum section: 0.22 mm² + braid
● Ethernet cables
● Ethernet switch
● Echelon U60 FT DIN USB Gateway (for LON FT10)
● High-gain GSM antenna
● High-gain LoRa antenna
● GSM or LoRa antenna cable
● Double-sided high performance adhesive tape
● Technical documentation of equipment
● Technical documentation of IoT sensors
● Schematic of the communication network(s) of the BMS
Hub configuration software
Each customer receives an email titled "Your Hub Is Coming" outlining the instructions for
installing the Desktop Application and configuring the Hub.
Step 1 - Download the Java SDK
Step 2 - Install the Desktop application
Step 3 - Run the Desktop Application
Read the Hub Desktop Application guide for more information.
2021-08-V1.3 3
The power supply of the Hub
Make sure that the Hub has been activated beforehand on the user console.
● Ideally, place the Hub in an electrical enclosure or cabinet.
● This type of equipment is not suitable for installation in places that can
accommodate children.
● Attach the Hub:
○ Mount the Hub on a DIN rail.
○ Or attach 2 screws to a wall and hook the Hub using the notches on the back
of the case: Screws of maximum 4 mm in diameter, with a head of maximum
2021-08-V1.3 4
7.5 mm diameter, a spacing of 89.4 mm.
● To avoid any risk of injury caused by the Hub falling, the Hub must not be installed
more than 2 meters from the ground.
● Use a DC power supply of 12-24V DC +/-10%, 2A Max.
2021-08-V1.3 5
● Install the original antenna delivered with the Hub.
● Screw the cable into the power connector of the Hub.
2021-08-V1.3 6
● Connect the cable to the power supply.
● Check that the "Power" LED is lit (steady green light).
2021-08-V1.3 7
● The Hub is protected against overvoltage, undervoltage, overcurrent from the
power supply with indication by LED: green LED when the power supply is
compatible, red LED if it is not suitable.
● Wait for ten seconds: the "Heartbeat" LED flashes (green light).
● Wait for the GSM LED to flash; if the LED does not flash after a few minutes, see
the GSM Antenna chapter.
● Check that the Hub appears on the console: the presence indicator of the Hub
changes from red to green.
● If the Hub appears on the console, it is functional; you can go to the connection
step of the Hub to the equipment and/or the network of the building.
● If the Hub does not appear on the console, see the GSM Antenna chapter.
2021-08-V1.3 8
To connect the Hub to the BMS
● Determine the type(s) of network(s) associated with the BMS (communication
protocols between the BMS server and the technical equipment).
● Obtain, if possible, the schematic of the communication network(s) of the BMS.
Identify where and how the BMS server connects to the building’s network.
2021-08-V1.3 9
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
