Waterous CPK-5 Series Manual de usuario

CPK-5 Fire Pumps

InstallationInstructions

Table of Contents

Safety Information ......................................................2

Introduction.................................................................3

General Description....................................................3

Pump Mounting - General Information.....................3

Pump Mounting........................................................4-9

Pump and Transmission.........................................4-7

Oil Pump and Cooler..............................................8-9

Final Checks..............................................................10

Lubrication...............................................................10

Testing ....................................................................10

Read through the installation in-

structions carefullybefore installing

yourWaterous CPK-5 Series Fire

Pump.

NOTE: Instructions subject to change without notice

F-1031, Section 3046 (Revised: 12/7/18)

Waterous Company, 125 Hardman Avenue South, South St. Paul, Minnesota 55075 USA (651) 450-5000

www.waterousco.com

F-1031, Section 3046

Page 2 of 10

Read through and communicate safety information to the end user of this Waterous Fire Pump.

SafetyInformation

WARNING

Death or serious personal injury might occur if proper

operating procedures are not followed. The pump op-

erator, as well as individuals connecting supply or dis-

charge hoses to the apparatus must be familiar with

pump operating instructions as well as other operating

instructions and manuals for the apparatus, water hy-

draulics and component limitation.

WARNING

Pressure Hazard. May result in personal injury.

Prior to connection or removal of hoses, caps or other

closures with pump intake or pump discharge connec-

tions, relieve pressure by opening drains or bleeder

valves.Bleedervalves shouldalso beused while filling

a hose connected to an intake with water.

WARNING

Scalding Water Hazard. May result in serious

burns.

When operatingthe pump, be sure to open at least one

discharge valve slightly to prevent the pump from over-

heating. If the pump runs for a few minutes completely

closed, it may heat the water enough to scald some-

one when the valve is opened. Overheating can dam-

age the packing, seals and other pump parts. If the ap-

paratus builder has installed a by-pass system or other

provision designed to prevent overheating, opening a

discharge valve may be unnecessary.

F-1031, Section 3046

Page 3 of 10

Introduction

This instruction covers the installation of a Waterous CPK-

5 Series firepump.TheCPK-5 is rated at 320 GPM @ 1350

PSI (1200 l/min @ 93 bar)

The CPK-5 is available with the following transmission:

•

Extra Heavy Duty K Series - The K transmission is a

gear driven transmission designed primarily to be

driven bya power take-off or power divider. (see Figure

1).

The following installation instructions are available:

•

Priming System, F-1031, Section 3006

•

Manifold Drain Valves, F-1031, Section 3008

•

Pressure Control System, F-1031, Section 3010

•

Overheat Protection Manager, F-1031, Section 3015

Before proceeding with the installation of the CL, read the in-

structions carefully. Check the appropriate dimensional draw-

ings in the Engineering Manual as needed.

Pump Mounting - General Information

Select a mounting location which will make the pump and its

accessories readilyaccessibleformaintenance.

Table 2 gives maximum universal joint angles for installations

where propeller shaft flanges are parallel and yokes are

aligned. Refer to this table when positioning a pump to deter-

mine proper shaft angles. Be sure to keep at least a minimum

of 1U-joint operating angle, but do not exceed those speci-

fied in the table. This is the preferred method of propeller shaft

installation. For additional information on this method, or for

alternative methods, see driveshaft installation guidelines

such as Spicer/Driveshaft InstallationTechniques, J-3311.

CAUTION

Be sure the propeller shafts used are of the slip-joint de-

sign. Frame deflection, temperature changes and similar

factors may cause a propeller shaft without slip-joints to

produce severe axial loads on the bearings and damage

the pump.

Table 2. Maximum U-joint Operating Angles

Driveshaft RPM

Maximum Operating Angle

5000

3.2

4500

3.7

4000

4.2

3500

5.0

3000

5.8

2500

7.0

2000

8.7

1500

11.5

NOTE: The angles shown in Table 2 are the maximum

recommended U-joint operating angles and are directly

related to the speed of the driveshaft. Any U-joint oper-

ating angle greater than 3will lower the U-joint life and

may cause vibration1.

1 From Spicer Driveshaft Installation Techniques, FormJ-3311 dated5/94.

F-1031, Section 3046

Page 4 of 10

Pump Mounting - CPK-5 Series

Figure 1 shows the mounting areas on a CPK-5 pump. To

mountthepump/transmissiontothe vehiclechassis, construct

a bracket that willspantheframerails of the vehicleandattach

to the transmission mounting holes (several locations are pro-

vided).

NOTE: Before installation, make sure your pump has

the right rotation as compared to the driveshaft rota-

tion (see dimensional drawings for correct rotation

configurations).

Position the pump/transmission within the vehicle frame

rails and secure the brackets (not supplied) to the vehicle

frame.

Support the pump by using the mounting plate on the pump

as shown in Figure 1.

NOTE:Tightenthemounting screws to standard torque

specifications.

Finally, provide adequate support for any intake and dis-

charge piping assemblies.

Figure 1. CPK-5 Mounting Diagram

(6) Mounting Holes

(7/16-14 UNC-2B x .625 in. deep)

(2) Mounting Holes

(7/16-14 UNC-2B x .625 in. deep)

Pump Mounting Plate

F-1031, Section 3046

Page 5 of 10

Figure 2. Pump Dimensions,

Inverted Transmission

Pump Mounting –CPK 5 Series

(con’t)

F-1031, Section 3046

Page 6 of 10

Pump Mounting –CPK 5 Series

(con’t)

Figure 3. Pump Dimensions, Horizontal Transmission

F-1031, Section 3046

Page 7 of 10

Pump Mounting –CPK 5 Series

(con’t)

Figure 3. Pump Dimensions, Vertical Transmission

F-1031, Section 3046

Page 8 of 10

Oil Pump and Cooler Mounting

Figure 4 shows mounting locations and connection points

for the oil pump and cooler that is used on the CPK-5. NOTE: Before installation, make sure your pump has

the right rotation as compared to the driveshaft rota-

tion (see dimensional drawings for correct rotation

configurations).

Figure 4. Oil Pump and Cooler Mounting Diagram

Figure 5.Oil Pump and Cooler Mounting Diagram Continued

F-1031,Section 3046

Page 9 of 10

Final Checks

After thepump,accessories,pipingand miscellaneous con-

nections are completely installed, check the points listed

below:

Lubrication

K Transmission

Gear lube spec: 75W-90 full synthetic.

Capacity:

Inverted mounting: 1.2 quarts

Horizontal mounting: 1.5 quarts

Vertical mounting: 1.6 quarts

(Capacity measurements are approximate and

include the transmission, oil cooler, and oil

pump. Hoses and fittings are not included.

Adjust accordingly to application).

Oil fill procedure:

1. With oil level plug installed, fill transmission

with 1.5 quarts of gear lube.

2. Run electric oil pump for 1 minute.

3. Stop oil pump.

4. Remove oil level plug.

5. Drain excess oil or add oil until a small

stream of oil runs out oil level hole.

6. Install oil level plug.

7. Repeat steps 2-6 until no additional oil is

required.

Testing

Perform the tests listed in F-1031, Section 1000, “Centrifu-

galFire Pump Principles of Operation, Inspection Tests and

Troubleshooting Guide.”During the running tests, monitor

the smoothness of operation, listen for unusual noises and

check for leaks.

CAUTION

Failure to properly lubricate the pump, transmission or

primers may result in serious damage to the equip-

ment.

F-1031, Section 3046 Page 10 of 10

Otros manuales para CPK-5 Series

Tabla de contenidos

Otros manuales de Bomba de agua de Waterous

Waterous

Waterous CP-4 Manual de usuario

Waterous

Waterous Floto-pump M Guía de solución de problemas

Waterous

Waterous TC10 Manual de usuario

Waterous

Waterous HL Series Manual de usuario

Waterous

Waterous CG Series Manual de usuario

Waterous

Waterous CP-1 Series Manual de usuario

Waterous

Waterous CZ Series Manual de usuario

Waterous

Waterous CAFS-CP-2 Series Instrucciones de instalación y funcionamiento

Waterous

Waterous HLU Series Instrucciones de instalación y funcionamiento

Waterous

Waterous AQUIS 1.5 Manual

Waterous

Waterous CX Series Manual

Waterous

Waterous PB18 Series Manual de usuario

Waterous

Waterous CP-4 Manual de usuario

Waterous

Waterous Floto-pump IL1330 Guía de solución de problemas

Waterous

Waterous CX Series Manual de usuario

Waterous

Waterous Eclipse ES TC20 Guía de instalación

Waterous

Waterous CM Series Manual de usuario

Waterous

Waterous TC20 Series Manual de usuario

Waterous

Waterous PB18 Series Guía de instalación

Waterous

Waterous CR Series Guía de solución de problemas

Waterous

Waterous E500 Series Guía de instalación

Waterous

Waterous Foam Manager Manual de usuario

Waterous

Waterous CS Series Guía de instalación

Waterous

Waterous S200-P Series Guía de solución de problemas

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario