Watermark SH-35WF Manual de usuario

No.

1 Mounting Screw

2 Shower head (A)

3 Shower head (B)

4 Mounting Guide

5 Mounting Plate

6 Lock Nut

7 Washer

8 Shower Nipple

9 Wall Mount / Toggle Screw

Note: The shower head/spout is approximately 11 lbs

Component

Quantity

Installation Guide for

SH-35WF, 35-WBSWF (AKA TBSPT-35WF)

350 Dewitt Avenue, Brooklyn, NY 11207 USA T: 718.257.2800 F: 718.257.2144 E: info@

watermark-designs.com

6 3/4'' Center to Center

Mounting Plate

Wall mount / Toggle Screws

Shower / Spout Nipple

1/2'' NPT MALE

Mounting Guide

WALL

2A. Align the mounting plate to the wall using the mounting guide and

position it as desired.

(Note: Position of mounting guide will dictate the orientation of the

shower head/spout)

2B. Once the desired orientation is established, mark the points in which

the holes for the wall mount screws will be located

(Note: The wall mount screw hole dimensions shown on the left figure

indicates center to center)

1A. Detach the mounting plate from the backside of the shower head/

spout by

unscrewing the two allen screws (mounting screws) located on

the

bottom side of shower head/spout B (refer to parts list view)

1B. Connect the shower nipple to the supply line, followed by the

mounting guide.

3A. Drill wall with a hole size of 21/64'' with a maximum

depth of 1 11/32''. This depth will allow the lock nut to fasten

the mounting plate until it braces the wall.

See below for detailed diagram

3B. Once the hole has been drilled, remove the mounting plate

from the wall to insert the wall mount screws into the wall.

3C. Re-attach the mounting plate to the wall with the

wall mount screws and mounting guide properly aligned.

3D. Fasten mounting plate to the wall with the washers

and lock nut.

Wall

11/32''

Mounting Plate

Washer / Lock Nut

MIN. Depth of Hole 1 11/32''

Wall Mount / Toggle Screw Application

4A. After securing the mounting plate onto

the wall, remove the mounting

guide from

the shower head/spout nipple.

4B. Mount the shower head/spout onto the mounting

plate and secure the two parts together with

the

mounting screws.

Mounting Screws

Wall Mount Screw

9 7/8"

5 3/8''

6 3/4"

1/2-14 NPT

2 3/8"

3/4"

5/8"

1/4"

Approximate Weight: 11 lbs

SCALE: 2:1

REV:

6/19/2013

Meets the applicable requirements of ASME A112.18.1-2005/CSA B125.1-05, entitled “Plumbing Supply Fittings”

350 Dewitt Ave Brooklyn NY 11207 I t: 718-257-2800 I f: 718-257-2144 I e: [email protected] I www.watermark-designs.com

SH-35WF

Lavatory Widespread

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorio de baño de Watermark

Watermark

Watermark Beverly Roosevelt CRY4 Manual de usuario

Watermark

Watermark Lily LLD4 Manual de usuario

Watermark

Watermark Elements 21 Series Manual de usuario

Watermark

Watermark PB-8524 Manual de usuario

Watermark

Watermark Edge 35-2-ED1-PC Manual de usuario

Watermark

Watermark Rainey RNS4 Manual de usuario

Watermark

Watermark AUT-WT1 Manual de usuario

Watermark

Watermark aquaBUBBLER ABS14 Manual de usuario

Manuales populares de Accesorio de baño de otras marcas

DURAVIT

DURAVIT C.1 C15240 0090 Manual

Heatstore

Heatstore HSTRL500WTN Manual de usuario

Sunshower

Sunshower PURE SOLO Manual de usuario

Delabie

Delabie Delabie Sporting 714700 Manual de usuario

Kohler

Kohler K-13056 Instrucciones de montaje

ESS

ESS Container TCL-11 Manual de usuario

Mustee

Mustee 22C Manual de usuario

VITRA

VITRA V-Flow Manual de usuario

baliv

baliv DUK-80.30 T Manual de usuario

Malmet

Malmet B105BT Manual de usuario

bathstore

bathstore Transition H1690MM Guía

BELLOSTA

BELLOSTA Edward 0800/M Manual de usuario

baliv

baliv DU-5160 Manual de usuario

Franke

Franke PRTR0006 Manual de usuario

Gessi

Gessi RILIEVO 59011 Manual de usuario

noken

noken VITAE 100188525-N299998810 Manual de usuario

Allen + Roth

Allen + Roth 1142VA-30-201 Manual de usuario

Britex

Britex HBDA Manual de usuario