Warn 70924 Manual de usuario
WARN® INDUSTRIES PAGE 1 71047A0
INSTALLATION INSTRUCTIONS
MULTI-MOUNT 4.0CI WINCH
Part Number: 70924
Applications: KAWASAKI MULE 3000 & 3010
Rear Receiver Installation
As you read these instructions, you will see NOTES, CAUTIONS, and WARNINGS. Each message has a
specific purpose. NOTES are additional information to help you complete a procedure. CAUTIONS are
safety messages that indicate a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. A CAUTION may also be used to alert against unsafe practice or possible equipment
damage. WARNINGS are safety messages that indicate a potentially hazardous situation, which, if not
avoided could result in serious injury. CAUTIONS and WARNINGS identify the hazard, indicate how to avoid
the hazard, and advise of the probable consequence of not avoiding the hazard. PLEASE WORK SAFELY!
Before You Begin
This kit is compatible with WARN’s line of ATV winches. Winch sold separately. Please read WARN’s
Winching Technique guide provided with the winch prior to use of this product.
Table of Contents
I. Parts List .......................................................2
II. Tools Required ..............................................2
III. Rear Receiver Installation .............................3
IV. Electrical connections.....................................4
V. Maintenance/Care .........................................4
CAUTION
Winch and Equipment Damage
This mount is designed for a 4000 lb. winch.
Using a higher capacity winch may cause personal
injury or severe damage to the mount or ATV
Read installation and operating instructions thoroughly
WARN® INDUSTRIES PAGE 2 71047A0
B2
A3
A4
B1
B5
B4
B4
B3
B3
B4
B3 B4
B3
B4
B4 B3
B5
B1
B3
A4
B3
B4
II. Tools Required
• Ratchet
• Sockets: 12mm, 13mm, 1/2”, 7/16”
• Wrenches: 12 mm, 13mm, 1/2”
I. Parts List
Ref Part # Description Qty
A3 68599 Rear Receiver 1
A4 68593 Brkt Rear Receiver 2
B1 22502 5/16-18 x 2 1/2 Hex Cpsc 4
B2 69308 U-Bolt 5/16-18 x 2 x 2 11/16 2
B3 2002 5/16-18 Locking Hex Nuts 12
B4 1324 5/16 Flat Washer 16
WARN® INDUSTRIES PAGE 3 71047A0
IV. Rear Receiver Installation
1. Begin by raising the dump box and locking into
position as shown in figure 1.
2. Place the rear receiver (A3) into position on the
Mule as shown in figure 2.
3. Attach the rear receiver tube assembly to the
cross tube on the Mule using two 5/16-18 u-bolts
(B2), 5/16 flat washers (B4), and 5/16-18 locking
hex nuts (B3) as shown in figure 3. Tighten the
bolts to a recommended torque of 10-12 ft-lb
(16 N-m).
4. Attach the rear receiver tube assembly to the two
side frame rales using the rear receiver brackets
(A4). The two brackets will attach to the tube
assembly using two 5/16-18 x 1 hex bolts (B5),
flat washers (B4), and locking hex nuts (B) shown
in figure 4. Tighten the bolts to a recommended
torque of 10-12 ft-lb (16 N-m).
5. Using the two side brackets (A4) as clamps.
Clamp them to the side frame rails using two
5/16-18 x 2 1/2 hex bolts (B1), 5/16 flat washers
(B4), and 5/16-18 locking hex nuts (B3) as shown
in figure 4. NOTE: If this unit is being installed on
a Desiel Mule only one of the 5/16-18 x 2 1/2 hex
bolt will be used in the bottom hole of each side
bracket.Tighten the bolts to a recommended
torque of 10-12 ft-lb (16 N-m).
Rear receiver mounting is now complete move to
section VI, entitled “Maintenance/Care”.
Figure 1
Figure 2
Figure 3
Figure 4
WARN® INDUSTRIES PAGE 4 71047A0
VI. Maintenance/Care
•Inspect all metal parts on the winch, winch mount,
and related hardware. Replace all that appears
rusted or deformed prior to use.
•Inspect all nuts and bolts on the winch, winch mount,
and related hardware prior to each use. Tighten all
nuts and bolts that appear to be loose. Stripped,
fractured, or bent bolts or nuts need to be replaced
WARNING
Failure to perform regular inspections and
maintenance on the winch, winch mount, and
related hardware may result in vehicle
damage and operator injury or death.
Rear receiver mounting is now complete move to
section VI, entitled “Maintenance/Care”.
V. Electrical connections
•Install the electrical according to the manual that is
with the carrier and with the winch.
•Route the two power cables for the front and rear
along the frame making sure to avoid any sharp
edges or moving parts. Make sure to avoid any
surfaces that may become hot when the vehicle is
operating.
Tabla de contenidos
Otros manuales de Cabrestante de Warn
Warn
Warn Zeon Control Pack Relocation Kit Manual de usuario
Warn
Warn VRX 25 Manual de usuario
Warn
Warn 2.5ci Manual de usuario
Warn
Warn 103420 Manual de usuario
Warn
Warn 685000 Manual de usuario
Warn
Warn 90250 Guía de solución de problemas
Warn
Warn ZEON Especificaciones
Warn
Warn 61019 Manual de usuario
Warn
Warn 39116 Manual de usuario
Warn
Warn 72492 Manual de usuario
Warn
Warn 72008 Manual de usuario
Warn
Warn Endurance 12.0 Manual de usuario
Warn
Warn PULLZALL 24Vdc Manual de usuario
Warn
Warn A2000 Manual de usuario
Warn
Warn 71983 Manual de usuario
Warn
Warn 84705 Manual de usuario
Warn
Warn TABOR 8000 Manual de usuario
Warn
Warn PN 61020 Manual de usuario
Warn
Warn 60272 Manual de usuario
Warn
Warn PROVANTAGE 4500-S Instrucciones de funcionamiento
