Walkera Runner 250 PRO Manual de usuario

www.walkera.com

QUICK START GUIDE

18th-OCT-2016

V1.0

-2-

13-14

1.0 Get to know your aircraft

2.0 Get to know your Remote Controller

3.0 Specifications

4.0 Attention before Flying

5.0 Charge the Battery

6.0 Prepare the Remote Controller

7.0 Prepare the aircraft

8.0 Ready to Fly

10-12

8.1 Starting the aircraft

8.2 GPS indicator lights

8.3 Motor Unlock / Lock

9.0 Operation Instruction

10.0 End Flying

11.0 Additional remarks

11.1 DEVO 7 Remote Controller Setting

11.2 TX5834(FCC)/TX5835(CE) Video transmitting channel selection

11.3 OSD interface information Introduction

11.4 Introduction for FCS-250 Main Flight Controller

11.5 Introduction for DEVO-RX717 receiver

11.6 Brushless ESC and Brushless Motor connection diagram

11.7 Compass Calibration

12.0 Instructions for GA005 balance charger

Contents

-3-

The RUNNER 250 body is created using CFP for outstanding crash survivability.

Modern industrial and modular design, improves the product performance and permit easy

maintainance and upgrades.

Advanced 5.8ghz live video and OSD system, for a unforgettable visual FPV experience.

Equip with dual GPS module, the RUNNER 250 advance can realize GPS hold mode, Circle Flight,

Hyper IOC and one key return to home.

1.0 Get to know your aircraft

5. Counterclockwise motor

(dextrogyrate thread is clockwise)

6. Clockwise propeller

7. Counterclockwise propeller

8. GPS

9. SBUS/PPM connection port

10. 5V power output port

11. FCS-250 Main Controller

12. Battery: 11.1V 2200mAh 25C 3S Li-Po

13. Transmitter code switch

14. Mushroom antenna

15. DUAL reciever antennas

for best performance

* always extend before flying

16. Red LED light x2

17. Turn indicator light x4

18. OSD code switch:

Slide the code switch “1” to “ON” to start the OSD

1. Camera

2. Lighting Lamp x2

3. Landing gear x4

4. Clockwise motor (levogyrate thread

is counterclockwise)

* To avoid property loss and personal injury caused by wrong operation, please read the manual carefully before flying.

Quick Start Guide

-4-

ＤＥＶＯ－７

GPS-hold ModeManual Mode

MIX Switch to “0” MIX Switch to “1” MIX Switch to “2”

Return TO Home

2.0 Get to know your Remote Controller

Equipped with the Manual Mode / GPS hold mode / one key return to home / Circle Flight / Hyper IOC,

camera controlling switches, the RUNNER 250 is easier to control.

(You can select suitable flight mode according to your flying skill.)

1. HOLD TRN switch

2. GEAR switch

3. AUX2 control

4. Left stick

5. Left trim

6. RUDD trim

7. UP+ key

8. DN- key

9. EXT key

10. FMOD - Flight Mode Switch

11. MIX - Control Mode Switch

12. ELEV/AILE/RUDD D/R Switch

13. Right stick

14. Right trim

15. Power switch

16. AILE trim

17. R+ key

18. L- key

19. ENT key

FMOD(FMD) Switch to “1”

Position: Hyper IOC Mode

FMOD(FMD) Switch to “2”

Position: Circle Flight Mode

Take the "MODE 2 (Throttle stick on the left)" as an example. The left stick controls the aircraft's altitude and

heading, while the right stick controls its forward, backward, left and right movements.

Left Stick Right Stick

Forward

Backward

Left Right

Down

Turn

Left

Turn

Right

* 1) MODE 2 (Throttle stick on the left): Left stick- THRO / RUDD; Right stick - ELEV / AILE.

2) MODE 1 (Throttle stick on the right): Left stick- ELEV / RUDD; Right stick - THRO / AILE.

Quick Start Guide

When aircraft backward, the left/right turn indicator lights will be solid.

When aircraft lean left, the left turn indicator light will be solid.

When aircraft lean right, the right turn indicator light will be solid.

When aircraft turn left, the left turn indicator light will flash.

When aircraft turn right, the right turn indicator light will flash.

-5-

Frequency：

Output Power：

Current drain：

Power Supply：

Output Pulse：

2.4GHz DSSS

≤100mW

≤230mA(100mW)

5# Battery 8x1.5V or NiMH 8x1.2V 1600-2000mAh

1000-2000mS(1500Ms Neutral)

205mm

221mm

143mm

117mm

3.0 Specifications

Aircraft

Main Rotor Dia.:

Overall (L x W x H):

Weight:

Remote Controller:

Receiver:

Main Controller:

Transmitter:

Brushless Motor:

Brushless ESC:

Battery:

Flight Time:

Working Temperature:

143mm

221 x 205 x 117mm

464g (Battery excluded)

DEVO 7

DEVO-RX717

FCS-250

TX5834(FCC)/TX5835(CE) (OSD included)

WK-WS-28-014A(CW/CCW)

F210 ESC

11.1V 2200mAh 25C 3S LiPo

10~12mins

-10℃~ +40℃

Camera(800TVL)

Horizontal Resolution:

System Commitee:

Video Out:

Power Input:

800TVL

PAL/NTSC

1.0Vp-p/75Ω

DC 12V

DEVO 7 Remote Controller

5.8G wireless image transmission

TX5834(FCC) Bind B section: 8 channels

TX5835(CE) B section: 8 channels

TX5834(FCC) output power ≤200mW

TX5835(CE) output power ≤25mW

TX5834(FCC) / TX5835(CE) Transmitter

Quick Start Guide

-6-

Attention:

Please refer to Page 18 for details of GA005

balance charger.

Power Adapter

GA005 charger

11.1V 2200mAh

LiPo battery

3 Cell DC 11.1V

Battery box

1) The RUNNER 250 is recomended for pilots, 14 years or older, with RC hobby experience.

Only fly the RUNNER 250 in dry weather, with low wind, please do not fly in rain or heavy foggy conditions.

3) Always choose large open fields for flying. Check local LAW and ordinances for legal flying areas.

4) Always keep at least 10 feet distance to the aircraft when armed, to avoid injury from high-speed propellers

on the ground or while flying. Always disarm before handeling the aircraft.

5) Do not fly close to high-voltage power lines, cellphone towers, or radio towers, as these may disrupt

your control signal.

6) ALWAYS check local laws BEFORE flying. NEVER fly over crowds, concerts or sports stadiums.

4.0 Attention before Flying

5.0 Charge the Battery

Insert the power adapter(100~240V 50/60HZ), connect

the output end to the GA005 balance charger, the balance

charger is red LED at this time.

During charging, Red LED is continuously flashing. If

saturated, Red LED becomes solid green lighting.

Insert the battery charging terminal into 3 Cell DC 11.1V

charger socket.

6.0 Prepare the Remote Controller

Open the battery cover and remove the battery box. According

to the battery positive and negative polarity, install 8pcs 5#

batteries or 8pcs NiMH batteries with same volume.

Warning:

Battery polarities must be correctly installed.

When insert the plug of battery box into power

socket of remote controller, the fool-proofing

port must be inserted into fool-proofing port.

Quick Start Guide

-7-

7.0 Prepare the aircraft

Install 5.8G antenna

Firstly install 5.8G antenna onto the transmitter,

and tighten with open-end wrench.

Open-end

wrench

Install propellers

Fix the CW propeller( ) onto the CW motor

according to the direction of blue arrow, and fix the

CCW propeller( ) onto the CCW motor according

to the direction of orange arrow.

Tighten the propellers manually and make sure the

propeller is installed in proper way and fastened.

Attention:

Install prop by hand and tighten by holding

the motor with the included wrench.

You can also use the wrench to help remove

broken props in case of a crash.

Open-end

wrench

CW propeller

( )

CW propeller

( )

CCW propeller

( )

CCW propeller

( )

Front

Battery installation

Put the battery and the Battery anti-slip mat into the

RUNNER 250, balance the gravity, keep the

head and

the tail parts aligned, then fasten the battery

with the

Velcro strap.

Battery anti-slip mat

Battery

Gravity center adjustment

Grab the RUNNER 250 by the COG line

(center ofgravity). See the illustration for the COG.

Adjust the battery forward-backwards until the quad

balances.

Gravity Center line

Quick Start Guide

-8-

8.1 Starting the aircraft

8.0 Ready to Fly

Attention:

Place the aircraft in a wide open space, with the rear facing you.

(This position is known as “TAIL IN”)

Put all the function switches to the 0 position, put all trims and dials to the Middle position,

move the throttle to the lowest position, then turn on the Remote Controller.

A video receiving equipment is needed( such as Goggles glasses, etc. ) to display

an image and OSD information.

(Setting method please refer to P15)

Turn on the Remote Controller. (Make sure all the

function switches, all trims/knobs and throttle stick

at the lowest position)

Put the aircraft to the horizontal place and connect

the aircraft power. (make sure the positive and

negtive connected correctly)

ALWAYS unfold the two reciever anteannas to

their correct STRAIGHT UP position before flying.

Do not fly without properly unfolding the antennas.

Do not move the aircraft during start-up.

Tips:

The RUNNER 250 have a low-voltage alarm beeper.

And the OSD give you a visual reference for the remaining battery power.

When voltage reach below 10.8 volts the LEFT red LED lights will flash slowly and the beeper

will sound alarm.

WARNING: Do not hesitate to land when you hear the alarm or see the OSD indicating 10.8 volts.

Tail part Right red LEDLeft red LED

Receiver antenna

Quick Start Guide

he red LED light on the left of aircraft flashes slowly

until goes out, indicating that the IMU preheating

complete. If it issuing the sound of "BB"

that it is

fail to IMU preheating

. Pls restart the aircraft.

-9-

Motor Unlock

8.2 GPS indicator lights

When the right red LED light (GPS) begin to flash, you can work GPS function.

8.3 Motor Unlock / Lock

Quick Start Guide

Motor Lock

NOTICE: The motors are LOCKED by default after successful binding.

TEST: Push the throttle stick up a little, the motors will not start when locked.

MODE 1 (Throttle stick on the right) MODE 2 (Throttle stick on the left)

ELEV/Rudder stick Throttle / Rudder stick

Throttle stick

ELEV stick

ELEV/Rudder stick

MODE 1 (Throttle stick on the right) MODE 2 (Throttle stick on the left)

Throttle / Rudder stick

Throttle stick

ELEV stick

After the success of IMU preheating, Check that all trims are neutral, the throttle stick is ALL the way Down

with the display indicating 0% throttle. Check that ALL switches are in the UP position.

Gently push the throttle stick down and move the rudder (YAW) stick to the left side and hold for more than

2 seconds. (on mode 2 radios throttle and rudder is the same stick).

You will see the left red LED light keeps on, indicating that motors are unlocked.

Be very careful at this point, as pushing the thottle up will start the motors.

You can test by pushing the stick up a little, the motors should start.

Gently push the throttle stick down and move the rudder (YAW) stick to the right side and hold for more than

2 seconds. (on mode 2 radios throttle and rudder is the same stick)

You will see the left red LED light turns off, indicating that motors are locked.

-10-

Attention:

GPS hold mode

Ground

MIX switch

to “1” position

FMOD(FMD) switch

to “2” position

MIX

Throttle stick

return neutral

Circle flight

9.0 Operation Instruction

1) Make sure that the received GPS signal (RIGHT red LED light blinks).

2) In the GPS mode, there are Altitude hold, fixed point, brake function, the flight speed is slower (≤5m/s).

3) If the GPS signal is poor or no signal, can only be Altitude hold, but not fixed point.

4) Switch to manual mode can not be fixed point.

Aircraft in

GPS hold mode

Attention:

1) Make sure that the received GPS signal (RIGHT red LED light blinks).

2) The aircraft is under quiescent state when it enters auto-circling. The circling function can only work after you set circle speed

and direction by toggling aileron stick left or right (-5m/s to +5m/s speed changeable, Default is 0m/s).

Dial to the left,

Clockwise circles

Dial to the right,

Counterclockwise circles.

Speed: The larger volatility toggling and longer holding time,

the faster circling. The slower the contrary.

3) Dial elevator stick up or down to change circle radius

(5m-50m radius changeable, Default is 5m)

Dial up, Circle radius turns small

Dial down, Circle radius turns large

Quick Start Guide

Please unlock the motor before start flying, then take off in manual mode(push up the throttle).

Otros manuales para Runner 250 PRO

Tabla de contenidos

Otros manuales de Zumbido de Walkera

Walkera

Walkera Runner 250 Manual de usuario

Walkera

Walkera Starlight F420 Manual de usuario

Walkera

Walkera ZHUN Manual de usuario

Walkera

Walkera Rodeo 110 Manual de usuario

Walkera

Walkera QRX350 PRO Manual de instrucciones

Walkera

Walkera ZHUN Manual de usuario

Walkera

Walkera QL 1800 Manual de usuario

Walkera

Walkera Voyager 5 Manual de usuario

Walkera

Walkera T210 MINI Manual de usuario

Walkera

Walkera UFOMX400S Manual de instrucciones

Walkera

Walkera TALI H500 Manual de usuario

Walkera

Walkera furious 320 Manual de usuario

Walkera

Walkera T210 MINI Manual de usuario

Walkera

Walkera W100S Manual de instrucciones

Walkera

Walkera V1100 PRO Manual de usuario

Walkera

Walkera R400 Manual de usuario

Walkera

Walkera Runner 250 PRO Manual de usuario

Walkera

Walkera Runner 250 Manual de usuario

Manuales populares de Zumbido de otras marcas

Ryze

Ryze Tello Manual de usuario

PowerVision

PowerVision PowerRay Manual de usuario

Force1

Force1 rogue F72 Manual de usuario

Zerotech

Zerotech DOBBY Manual de usuario

Protocol

Protocol VIDEODRONE AP Manual de usuario

dji

dji Matrice M210 Manual de usuario

MAKE

MAKE Terry Kilby Manual de usuario

SYMA

SYMA X440 Manual de usuario

RUKO

RUKO F11 Manual de usuario

SYMA

SYMA X5UW(720P) Manual de usuario

Dynali

Dynali 25 H Guía

dji

dji PHANTOM 4 Manual de usuario

Atlas

Atlas AtlasPRO Manual de usuario

Twodots

Twodots TVVIN BOARD Manual de usuario

GDU

GDU SAGA Manual de usuario

Ares

Ares ETHOS QX 130 Manual de usuario

dji

dji WIND-4 Manual de usuario

Potensic

Potensic D58 Manual de usuario