Wali WL-TTM-1 Manual de usuario

Otros manuales de Rack y soporte de Wali

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario

Supplied Parts List

2

(4)M4x12 Bolt-h (4)M4x30 Bolt-i (4)M6x20 Bolt-j

(2)Monitor Bracket (1)Bubble Level-a

Note: The mounting components and hardware supplied in this package are

not designed for installations to walls with steel studs or to cinder block walls.

If the hardware you need for your installation is not included, please consult

your local hardware store for proper mounting hardware for the application.

Tools Required 4mm Drill Bit

Phillips Screwdriver

10mm Masonry Bit

Carpenter's Level

(4)M6 Washer-f(8)M6/M8 Spacer-d (4)M4 Washer-e

(4)M8x20 Bolt-l (4)M8x35 Bolt-m (4)M8x50 Bolt-n

(4)Lag Bolt-q(4)Lag Bolt Washer-p (4)Concrete Anchor-r

(4)M8 Washer-g

(1)Wall Plate

(4)M4 Spacer-c

(4)M6x35 Bolt-k

(4)Bolt Cover-o

(1)Allen Key-b

65mm

4mm

Wood Studs Wall

16"(406mm)

qp

Step 1 Mounting the Wall Plate to the Wall

3

CAUTION!

WARNING

!This TV mount must be securely attached to the

vertical wall. If the mount is not properly

installed it may fall, resulting in possible injury

and/or damage.

Brick or Concrete Wall

60mm

65mm

10mm

qp

r

o

o

Step 2 Mounting the Monitor Brackets to a TV

First of all, Once you have

determined the correct diameter, please see the diagram as below. You will thread the

Bolt into the TV using the correct Washer(e,f,g), and using the spacer(c,d) if necessary.

Please make sure the Monitor Brackets are vertically centered and level with each

other.

make sure the diameter of the Bolt(h to n) your TV requires.

4

Step 3 0

Attaching TV to Wall Plate-Make Sure the Tilting Angle is 0

Warning: Some TVs may require two people to lift! We are not responsible for

personal injury or product damage.

First hook the Monitor Brackets over the top of the Wall Plate, then let the bottom of the

Monitor Brackets rotate to the bottom of the Wall Plate as shown in the diagram 3.1 and

3.2. Pull down straps to lock the Monitor Brackets to Wall Plate. Finally the Monitor

Brackets will sit behind the bottom tab on the Wall Plate as shown in the diagram 3.3.

3.1

3.2 3.3

h to n

e,f,g

c,d

(if necessary)

Step 4 Adjust the Tilting Angles

First loosen the bolts, then pull the TV to the desired angle, finally fasten the bolts.

Using the provided Allen Key(b).

5

Step 5 Remove the TV from the TV Mount

To take off the TV from the TV mount, you need to adjust the tilting angle to 0 degree

firstly. Then pull the straps to release the spring locking system. Hold the TV upward to

unlock the top hooks from the wall plate.

5.1

5.2

b