WAGO 750-512 Manual de usuario

Fieldbus Independent

I/O Modules

2DO 230V AC 2.0 A/ Relay 2NO

750-512

Manual

Version 1.0.2

ii • General

WAGO-I/O-SYSTEM 750

I/O Modules

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the correctness and com-

pleteness of this documentation. However, as errors can never be fully ex-

cluded, we would appreciate any information or ideas at any time.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the tra-

demarks of companies used and/or mentioned in the present manual are gener-

ally trademark or patent protected.

Content • iii

WAGO-I/O-SYSTEM 750

I/O Modules

Content

1Important Comments ................................................................................. 4

1.1 Legal Principles........................................................................................4

1.1.1 Copyright.............................................................................................4

1.1.2 Personnel Qualification .......................................................................4

1.1.3 Intended Use ........................................................................................4

1.2 Symbols.................................................................................................... 5

1.3 Number Notation......................................................................................5

1.4 Safety Notes .............................................................................................6

1.5 Scope ........................................................................................................6

2I/O Modules ................................................................................................. 7

2.1 Digital Output Modules............................................................................7

2.1.1 750-512 [2DO 230V AC 2.0 A/ Relay 2NO]...................................... 7

2.1.1.1 View................................................................................................7

2.1.1.2 Description......................................................................................7

2.1.1.3 Display Elements ............................................................................8

2.1.1.4 Schematic Diagram.........................................................................9

2.1.1.5 Technical Data ..............................................................................10

2.1.1.6 Process Image ............................................................................... 11

2.1.1.7 Load limiting value graph of the relay.......................................... 12

2.1.2 Contact Protective Circuit for Relay Modules .................................. 13

4 • Important Comments

Legal Principles

WAGO-I/O-SYSTEM 750

I/O Modules

1 Important Comments

To ensure fast installation and start-up of the units described in this manual,

we strongly recommend that the following information and explanations are

carefully read and abided by.

1.1 Legal Principles

1.1.1 Copyright

This manual is copyrighted, together with all figures and illustrations con-

tained therein. Any use of this manual which infringes the copyright provi-

sions stipulated herein, is not permitted. Reproduction, translation and elec-

tronic and photo-technical archiving and amendments require the written con-

sent of WAGO Kontakttechnik GmbH. Non-observance will entail the right of

claims for damages.

WAGO Kontakttechnik GmbH reserves the right to perform modifications al-

lowed by technical progress. In case of grant of a patent or legal protection of

utility patents all rights are reserved by WAGO Kontakttechnik GmbH. Prod-

ucts of other manufacturers are always named without referring to patent

rights. The existence of such rights can therefore not be ruled out.

1.1.2 Personnel Qualification

The use of the product detailed in this manual is exclusively geared to special-

ists having qualifications in PLC programming, electrical specialists or per-

sons instructed by electrical specialists who are also familiar with the valid

standards. WAGO Kontakttechnik GmbH declines all liability resulting from

improper action and damage to WAGO products and third party products due

to non-observance of the information contained in this manual.

1.1.3 Intended Use

For each individual application, the components supplied are to work with a

dedicated hardware and software configuration. Modifications are only per-

mitted within the framework of the possibilities documented in the manuals.

All other changes to the hardware and/or software and the non-conforming use

of the components entail the exclusion of liability on part of WAGO Kon-

takttechnik GmbH.

Please direct any requirements pertaining to a modified and/or new hardware

or software configuration directly to WAGO Kontakttechnik GmbH.

Important Comments • 5

Symbols

WAGO-I/O-SYSTEM 750

I/O Modules

1.2 Symbols

Danger

Always abide by this information to protect persons from injury.

Warning

Always abide by this information to prevent damage to the device.

Attention

Marginal conditions must always be observed to ensure smooth operation.

ESD (Electrostatic Discharge)

Warning of damage to the components by electrostatic discharge. Observe

the precautionary measure for handling components at risk.

Note

Routines or advice for efficient use of the device and software optimization.

More information

References on additional literature, manuals, data sheets and INTERNET

pages

1.3 Number Notation

Number Code Example Note

Decimal 100 normal notation

Hexadecimal 0x64 C notation

Binary '100'

'0110.0100'

Within ',

Nibble separated with dots

6 • Important Comments

Safety Notes

WAGO-I/O-SYSTEM 750

I/O Modules

1.4 Safety Notes

Attention

Switch off the system prior to working on bus modules!

In the event of deformed contacts, the module in question is to be replaced, as

its functionality can no longer be ensured on a long-term basis.

The components are not resistant against materials having seeping and insu-

lating properties. Belonging to this group of materials is: e.g. aerosols, sili-

cones, triglycerides (found in some hand creams).

If it cannot be ruled out that these materials appear in the component envi-

ronment, then additional measures are to be taken:

- installation of the components into an appropriate enclosure

- handling of the components only with clean tools and materials.

Attention

Cleaning of soiled contacts may only be done with ethyl alcohol and leather

cloths. Thereby, the ESD information is to be regarded.

Do not use any contact spray. The spray may impair the functioning of the

contact area.

The WAGO-I/O-SYSTEM 750 and its components are an open system. It

must only be assembled in housings, cabinets or in electrical operation

rooms. Access must only be given via a key or tool to authorized qualified

personnel.

The relevant valid and applicable standards and guidelines concerning the

installation of switch boxes are to be observed.

ESD (Electrostatic Discharge)

The modules are equipped with electronic components that may be destroyed

by electrostatic discharge. When handling the modules, ensure that the envi-

ronment (persons, workplace and packing) is well grounded. Avoid touching

conductive components, e.g. gold contacts.

1.5 Scope

This manual describes the Digital Output Module 750-512

2DO 230V AC 2.0 A/ Relay 2NO of the modular WAGO-I/O-SYSTEM 750.

Handling, assembly and start-up are described in the manual of the Fieldbus

Coupler. Therefore this documentation is valid only in the connection with the

appropriate manual.

750-512 [2DO 230V AC 2.0 A/ Relay 2NO] • 7

View

WAGO-I/O-SYSTEM 750

I/O Modules

2 I/O Modules

2.1 Digital Output Modules

2.1.1 750-512 [2DO 230V AC 2.0 A/ Relay 2NO]

2-Channel Relay Output Module AC 230 V, DC 30 V 2.0 A,

non-floating, 2 make contacts

2.1.1.1 View

13 14

750-512

Power jumper contacts

Data contacts

Relay 2

Status

Relay 1

Status

DO 2

AC 230 V

DC 30 V

DO 1

Fig. 2.1.1-1: 2-Channel Relay Output Module 750-512 g051200e

2.1.1.2 Description

The connected load is switched via the digital output (relay contacts) from the

control system.

The module has two output channels. Two actuators with ground (earth) wire

may be directly connected to signal output DO 1, N and PE (earth potential) or

signal output DO 2, N and PE.

Each module is equipped with one non-floating make contact relay per chan-

nel, i.e. the fieldside voltage supply (230 V AC or 30 V DC) is connected to

each terminal of the relay and is fed in via the internal power jumper contacts

of an adjacent supply module.

By closing a relay, the field power applied is switched to the second relay con-

nection of signal output DO1 or DO2.

The internal system voltage is used to trigger the relays.

The switching status of the two relays is indicated via green status LEDs.

8 • 750-512 [2DO 230V AC 2.0 A/ Relay 2NO]

Display Elements

WAGO-I/O-SYSTEM 750

I/O Modules

Any configuration of the output modules is possible when designing the field-

bus node. Grouping of module types is not necessary.

Attention

An additional supply module must be added for the field supply with AC

230 V / DC 30 V.

The AC 230 V or DC 30 V supply voltage for the field side and the and the 0

V and earth (ground) potential is made automatically through the individual

I/O modules by means of power jumper contacts

Warning

The maximum current of the internal power jumper contacts is 10 A. When

configuring the system it is important not to exceed the maximum/sum cur-

rent. However, if such a case should occur, another supply module must be

added.

Note

For the protection of relay coils and contacts, inductive loads must be damp-

ened with an effective protection circuit!

Examples of protection circuits can be seen in the section 2.1.2 "Contact Pro-

tective Circuit for Relay Modules".

The output module 750-512 can be used with all couplers/controllers of the

WAGO-I/O-SYSTEM 750.

2.1.1.3 Display Elements

LED Channel Designation State Function

off Make contact DO 1 opened

green 1 Status

Relays 1 on Make contact DO 1 closed

off Make contact DO 2 opened

13 14

Fig. 2.1.1-2: Display

Elements g050102x

green 2 Status

Relays 2 on Make contact DO 2 closed

750-512 [2DO 230V AC 2.0 A/ Relay 2NO] • 9

Schematic Diagram

WAGO-I/O-SYSTEM 750

I/O Modules

2.1.1.4 Schematic Diagram

DO 2

AC 230 V

DC 30 V

AC 230 V

DC 30 V

DO 1

0V 0V

Status

750-512

Fig. 2.1.1-3: 2-Channel Relay Output Module 750-512 g051201e

10 • 750-512 [2DO 230V AC 2.0 A/ Relay 2NO]

Technical Data

WAGO-I/O-SYSTEM 750

I/O Modules

2.1.1.5 Technical Data

Module Specific Data

Number of outputs 2 make contacts

Current consumption max. (internal) 100 mA

Switching voltage relay AC 250 V/DC 30 V

Switching power relay 500 VA/60 W

cosφmax = 0.4; L/Rmax = 7 ms

Switching current max. AC/DC 2 A

Switching current min. 10 mA at DC 5 V

Switching rate max. 30/min (at nominal load))

Pull-in time max. 10 ms

Bounce time typ. 1.2 ms

Dropout time max. 10 ms

Contact material Silver alloy

Mechanical life max. 2x107switching operatins

Electrical life min. 3x105switching operatins

(AC 2 A/250 V) or (DC 2 A/30V)

Isolation 1.5 kVeff. (System/Field)*

*2.5 kV rated surge voltage

overvoltage category III

Internal bit width 2 Bit out

Dimensions (mm) W x H x L 12 x 64* x 100

* from upper edge of 35 DIN rail

Weight ca. 55 g

Standards and Regulations (cf. Chapter 2.2 of the Coupler/Controller Manual)

EMC-Immunity to interference (CE) acc. to EN 50082-2 (96)

EMC-Emission of interference (CE) acc. to EN 50081-1 (93)

EMC-Immunity to interference

(Ship building)

acc. to Germanischer Lloyd (97)

EMC-Emission of interference

(Ship building)

acc. to Germanischer Lloyd (97)

Tabla de contenidos

Otros manuales de Unidad de control de WAGO

WAGO

WAGO 767-5803 Manual de usuario

WAGO

WAGO 750-469 Manual de usuario

WAGO

WAGO WAGO-I/O-SYSTEM 750-506 Manual de usuario

WAGO

WAGO 750-559/040-000 Manual de usuario

WAGO

WAGO WAGO-I/O-SYSTEM 750 750-481/003-000 Manual de usuario

WAGO

WAGO 767-4803/000-800 Manual de usuario

WAGO

WAGO 750-1515/040-000 Manual de usuario

WAGO

WAGO 751-3502 Manual de usuario

WAGO

WAGO 750-468/040-000 Manual de usuario

WAGO

WAGO 750-632 Manual de usuario

WAGO

WAGO 750-458 Manual de usuario

WAGO

WAGO 750-606/040-000 Manual de usuario

WAGO

WAGO 750-640 Manual de usuario

WAGO

WAGO 750-564 Manual de usuario

WAGO

WAGO 750-439/040-000 Manual de usuario

WAGO

WAGO 750-557/040-000 Manual de usuario

WAGO

WAGO 750-486/040-000 Manual de usuario

WAGO

WAGO 750-1416/040-000 Manual de usuario

WAGO

WAGO 750-654 Manual de usuario

WAGO

WAGO 750-405 Manual de usuario

WAGO

WAGO 750-523 Manual de usuario

WAGO

WAGO 750-481/040-000 Manual de usuario

WAGO

WAGO SPEEDWAY 767 Series Manual de usuario

WAGO

WAGO 753-668/000-004 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario

Flyron

Flyron FN-BC04 Manual de usuario