WAGNER Datamaster Manual de usuario

Quick Start Guide

Package Contents

1 DataMaster™ handheld unit

1 Bluetooth®Reader

1 USB power cable

1 SD memory card (installed)

DataMaster™ Quick Start Guide

DataMaster™ manual

Initial Battery Charge

Your DataMaster™ unit will require an initial charge to have

a fully operable battery capacity. To charge the DataMas-

ter™, connect the included USB power cable to the micro

port at the base of the unit and then to a computer USB port

or AC USB adaptor (not included) for use of a conventional

outlet. Allow 2-3 hours for the initial charge.

1Set Date and Time – Power on the DataMaster™ and

from the Main Menu, choose “Settings.” Select “Date/

Time” and set month, day, year, hour, minute and sec-

ond by touching the appropriate box and using the up

or down arrows at the bottom of the screen to select

the correct number. Select “OK” or the return arrow to

return to the “Settings” menu.

2Set Units – From the “Settings” menu, select “Units”.

Select “Fahrenheit” or “Celsius” according to require-

ments, as well as “Inches” or “Millimeters.”

3Set Backlight and Sound – From the “Settings” menu,

select “Backlight & Sound.” The Backlight level can

be modied by sliding the control tab to the desired

setting. Sound can be chosen as “Sound On” (default

setting) or “Sound Off.”

4Set Graph Scales – This optional setting lets you

view measurements in graphical display on the Data-

Master™. From the “Settings” menu, select “Graph

Scales.” From the Graph Scales screen you can set

the Minimum and Maximum RH and Temp values for

scaling purposes. A “Target RH” can also be set as

a reference.

Quick Start Guide

Taking Readings (Measurements)

Note: An SD memory card MUST be installed in order for the

DataMaster™ to take a reading with the Bluetooth® Reader. If

using a lockable SD card, the card must be unlocked to receive

the reading.

1Add a Job – From the “Tools” menu, select “Add Job.”

Job names must be a maximum of 8 alpha-numeric

characters. Once job name is entered, select “OK” to

add to job list. Multiple job names can be added at any

time. The job list can be reviewed at any time by select-

ing “View” from the main menu.

2Begin Taking Readings – Go to an already installed

Smart Sensor. Firmly insert the Bluetooth® Reader into

the Smart Sensor, holding it in place for approximately 3

seconds, then remove. After no more than 5 seconds,

the READING ACQUIRED display should appear on the

DataMaster™, if not, reinsert the Reader. The screen

will dismiss itself after approximately 3 seconds. If this

is the very rst reading for this sensor, you will be taken

to the “Select a Job” screen where you will assign this

sensor to the appropriate job from the job list. The rst

reading at a new site may take 3 to 7 seconds to initiaite

the rst connection. Once connected (indicated by the

BlueTooth icon in the title bar) all subsequent readings

should take only 1 to 2 seconds. Readings from that

sensor will be recorded in the assigned job le. Sensors

are non-transferrable between jobs, once assigned.

3Enter Sensor Information - When the DataMaster™ ac-

quires each initial sensor reading, touch the “Informa-

tion” button (“i” in a circle) on the bottom right corner

of the screen. On the “Sensor Info” screen, enter the

sensor location (Loc:) and the Hole Depth, which are

mandatory for correct reporting according to the ASTM

F2170 reporting protocol. Floor, Slab and Slab thickness

are optional, but may be used to provide additional in-

formation if desired. Once a sensor has been assigned

to a specic Job, subsequent readings from that sen-

sor will automatically be stored under that Job. Job site

data can be viewed on the “Graph” menu of the Data-

Master™, or by selecting individual sensors from the job

listing. Each reading will record the current slab internal

RH and Temperature, sensor serial number, sample (i.e.

2 of 3), date, time, dew point (DP) and ambient RH and

temperature.

Quick Start Guide

Taking Readings (Continued)

4Job site data can be viewed on the “Graph” menu of

the DataMaster™, or by selecting individual sensors

from the job listing. Each reading will record the current

slab internal RH and Temperature, sensor serial num-

ber, sample (i.e. 2 of 3), date, time, dew point (DP) and

ambient RH and temperature.

For more complete information on viewing and using your

Rapid RH®DataMaster™, consult your user manual, or

DataMaster™Layout

Front Back

A. Touch screen D. SD card slot (on side)

B. USB port (on bottom) E. Ambient RH/Temp sensor

C. On/Wake-Up button (on top) F. Hard reset hole

Otros manuales para Datamaster

Tabla de contenidos

Otros manuales de Instrumento de medición de WAGNER

WAGNER

WAGNER MMI 1100 Manual de usuario

WAGNER

WAGNER L606 Manual de usuario

WAGNER

WAGNER Layer Check LC 1000 Manual de usuario

WAGNER

WAGNER C575 Manual de usuario

WAGNER

WAGNER MMC 205 Manual de usuario

WAGNER

WAGNER RAPID RH Manual de usuario

WAGNER

WAGNER Rapid RH 4.0 EX Manual de usuario

WAGNER

WAGNER TITANUS SUPER-SENS Manual de usuario

WAGNER

WAGNER RS 500 Manual operacional

WAGNER

WAGNER SprayPackE Manual de usuario

WAGNER

WAGNER Datamaster Manual de usuario

WAGNER

WAGNER L622 Manual de usuario

WAGNER

WAGNER BI 2200 Manual de usuario

WAGNER

WAGNER C575 Manual de usuario

WAGNER

WAGNER FORCE DIAL FDL Series Manual de usuario

WAGNER

WAGNER L601-3 Manual de usuario

WAGNER

WAGNER Force Ten FDX Manual de usuario

WAGNER

WAGNER FORCE TEN Manual de usuario

WAGNER

WAGNER FORCE DIAL FDL Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario