Wagan 2544 Manual de usuario

RItem no. 2544

User’s Manual

500 Peak Amp Jumpstarter

with Air Compressor

Wagan and wagan.com are trademarks used by Wagan Corporation.

LED Work light

Charging Indicator

Volt Meter

On/Off

Safety switch

Battery check

button

USB Outlet

USB On/Off

Charging jack

Light switch

DC socket

On/Off switch

Air hose

12V DC socket

Heavy duty booster clamps

User’s Manual—Please read before using this equipment

Wagan and wagan.com are trademarks used by Wagan Corporation.

FRONT FEATURES & FUNCTIONS

Shock-absorbing

rubber base

Air compressor

gauge

Air compressor

On/Off switch

260PSI

air compressor

500 Peak Amp Jumpstarter with Air Compressor by Wagan Tech

Wagan and wagan.com are trademarks used by Wagan Corporation.

BACK FEATURES & FUNCTIONS

User’s Manual—Please read before using this equipment

Wagan and wagan.com are trademarks used by Wagan Corporation.

Thank you for purchasing 500 Peak Amp Jumpstarter with Air Compressor by

Wagan Tech. With normal care and proper treatment it will provide years of

reliable service. Please read all operating instructions carefully before use.

IMPORTANT

PRIOR TO USE, READ AND UNDERSTAND ALL WARNINGS, CAUTIONS

AND INSTRUCTIONS INCLUDED IN THIS INSTRUCTION MANUAL AND

THOSE PUBLISHED BY YOUR VEHICLE BATTERY MANUFACTURER AND

MANUFACTURER OF ANY DEVICE INTENDED TO BE USED WITH THIS UNIT.

RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CAUTIONS:

Never work alone with this product. Make sure that someone is available

to give assistance if needed.

Wear complete eye and clothing protection. Do not touch eyes while

working near battery.

Do not attempt to remove or replace the battery used in this device.

When the battery has reached the end of its useful lifetime, take the

entire unit to a battery recycling facility.

For proper and safe operation of the 12 Volt DC power accessory outlets

do not place anything into them except the plug of the accessory to be

used.

Remove metal jewelry such as rings, bracelets, necklaces and watches

while working with a lead acid battery. They can produce a short-circuit

that may cause severe burns.

Never charge or attempt to jumpstart a frozen battery.

Never allow clamps (positive & negative terminals) to touch together or

to connect the same piece of metal to prevent short-circuits and arcing.

•

500 Peak Amp Jumpstarter with Air Compressor by Wagan Tech

Wagan and wagan.com are trademarks used by Wagan Corporation.

Do not operate this device while wearing vinyl clothing. Static electricity

may be generated when vinyl clothing is rubbed.

This product is not intended for use in the rain or temperatures above

130°F.

Use only the provided chargers, cables and clamps. Unauthorized parts

may damage the unit.

The product must be properly assembled in accordance with the

assembly instructions before it is used.

This product has no consumer serviceable parts.

This product is not a toy. Keep out of the reach of children.

Keep battery terminals clean. Be careful to keep corrosion from coming

in contact with eyes.

Do not let the wires of the jumpstarter or attached appliances get wet.

Do not operate this unit in or around water. Water can damage the unit.

CHARGING AND RECHARGING:

WARNING: Do not overcharge this unit. Overcharging may result in

damage. Prior to charging, read and understand all instructions.

This product may arrive partially charged from the manufacturer. It is

recommended to fully charge the unit immediately after purchase and

before using for the ﬁrst time.

The red charging LED indicator will be illuminated while charging. After

charging period is completed, push the red “Battery Indicator Button”

and the battery voltmeter should register between 12–14V. The battery is

now fully charged.

Do not charge the unit for more than 48 hours continuously.

•

User’s Manual—Please read before using this equipment

Wagan and wagan.com are trademarks used by Wagan Corporation.

Do not charge the unit on a boat, boat ramp or dock since the electrical

cords and outlets used for charging could cause severe electrical shock

if they get wet.

It is recommended that the unit be in an upright position while charging.

Make sure both cable clamps (positive and negative) are placed in their

storage holsters when not in use.

CHARGING WITH THE 110V AC CHARGER:

Insert the AC charger plug into charging jack of the unit.

Insert the AC charger receptacle plug into an AC receptacle.

The unit times are as follows:

Initial ﬁrst time charge: 38 hours continuously

Recharge or between use: around 34 hours continuously.

When charging is complete, unplug the AC charger receptacle plug,

then the AC charger from the charging jack on the unit.

CHARGING WITH THE 12 VOLT DC CHARGER:

Insert the DC charger plug into the charging jack of the unit.

Insert the DC charger plug into a vehicle cigarette lighter socket.

Fully charge the unit for around 14 hours continuously, while the engine

is running.

When charging is completed unplug the DC charger accessory plug ﬁrst,

and then the DC charger from the charging jack on the unit.

•

500 Peak Amp Jumpstarter with Air Compressor by Wagan Tech

Wagan and wagan.com are trademarks used by Wagan Corporation.

JUMPSTARTING A VEHICLE

WARNING: Vehicles equipped with onboard computers may be affected

if the engine battery is jumpstarted. Read your vehicle owner’s manual

before attempting to start the vehicle to determine if external starting

assistance can be used. Failure to follow these instructions may cause

damage or even an explosion. Use safety glasses to protect eyes while

jumpstarting a battery.

Turn off the vehicle ignition and all other accessories (e.g. the radio,

lights, air conditioner and cellular phones].

Set the emergency brake and put vehicles with automatic transmissions

in park position.

Determine the polarity of the vehicle’s battery terminals. The positive

(POS, P, +) battery terminal usually is larger in diameter than the

negative (NEG, N, -) terminal. If you are unsure, you should refer to the

vehicle owner’s manual.

Determine whether your vehicle uses a negative or positive grounded

system:

Negative ground system: Negative battery terminal is grounded to

the vehicle chassis. Most vehicles use this system.

Positive ground system: Positive battery terminal is grounded to

chassis or any other part of the vehicle. If you are unsure, you

should refer to vehicle owner’s manual.

Access the clamps by pressing clamp handles inward. Pull the clamps

downward and remove the clamps from the holders in a downward

angle. Never allow clamps (positive & negative terminals) to touch

together or to contact the same piece of metal to prevent short-circuits

and arcing.

Determine if you are using a negative grounded system or positive

grounded system and follow the instructions for the system as indicated:

•

User’s Manual—Please read before using this equipment

Wagan and wagan.com are trademarks used by Wagan Corporation.

Follow instructions for a negative grounded system as indicated below:

Securely connect the positive (+) red clamp to the positive (POS,

P, +) terminal of the vehicle battery or the remote positive (+)

terminal if equipped.

Securely connect the negative (-) black clamp to the vehicle

chassis, engine block or a non-moving metal part of the vehicle

which is veriﬁed to be grounded. Do not clamp directly to

negative battery terminal, carburetor, fuel lines or sheet metal

body parts.

See jumpstarting step 7 to continue.

Follow instructions for a positive grounded system as indicated below:

Securely connect the negative (-) black clamp to the negative

(Neg, N, -) ungrounded terminal of the vehicle battery.

Securely connect the positive (+) red clamp to the vehicle chassis,

engine block or a non-moving metal part of the vehicle which is

veriﬁed to be grounded. Do not clamp directly to positive battery

terminal, carburetor, fuel lines or sheet metal body parts.

See jumpstarting step 7 to continue.

Set On/Off safety switch to “ON” after clamps are secure on battery

post.

Allow 2 or 3 minutes of charging time. It is recommended to have a

second person to assist holding the unit securely in place during the next

steps.

Turn on the vehicle to attempt to start the engine. If the vehicle does not

start after 4 to 5 seconds of engine cranking, then stop. Wait 3 to 4

minutes, and then try again. Repeat several times until the vehicle starts.

CAUTION: Excessive engine cranking can damage the vehicle starter

motor. If the engine turns but fails to start after several attempts, other

technical problems might be involved. Discontinue cranking the engine

•

500 Peak Amp Jumpstarter with Air Compressor by Wagan Tech

Wagan and wagan.com are trademarks used by Wagan Corporation.

until the other problem is determined and corrected.

Standing as far away from the vehicle battery as is practical, disconnect

the clamps in reverse sequence to the connection procedure:

For negative grounded systems, ﬁrst disconnect negative (black)

then positive (red) clamps.

For positive grounded systems, ﬁrst disconnect positive (red) then

negative (black) clamps.

USING THE AIR COMPRESSOR

WARNING: Check the item to be inﬂated for the manufacturer’s maximum

recommended inﬂation pressure. Avoid over-inﬂation. Most tires are properly

inﬂated between 24–35 PSI. Some truck and bicycle tires require 40 PSI or

more.

Inﬂating tires

Remove the cap from the air valve stem. Note: Make sure locking thumb

lever is in the UP position. If necessary, use a valve stem adapter.

Attach the stem connector to the valve stem. Make sure connector is

pushed onto the valve stem as far as possible.

Press down the locking thumb lever to engage.

Set the unit’s On/Off safety switch to the “ON” position.

Set the compressor On/Off switch to the “ON” position by pressing

down the section of the switch marked “I”. Note: In the event that the tire

is completely ﬂat, raise the vehicle using a recommended jack before

inﬂating the tire.

Monitor pressure on the air pressure gauge. Note: It is recommended to

use a separate air gauge to verify the actual inﬂation pressure.

10.

•

Tabla de contenidos

Otros manuales de Arranque remoto de Wagan

Wagan

Wagan iOnBoost V8 Manual de usuario

Wagan

Wagan Power Dome EX Manual de usuario

Wagan

Wagan JumpBoost V10 Air Manual de usuario

Wagan

Wagan iOnBoost V8 Manual de usuario

Wagan

Wagan Power Dome LT Manual de usuario

Wagan

Wagan iOnBoost v6 7501 Manual de usuario

Wagan

Wagan 2509 Manual de usuario

Wagan

Wagan 900 Amp Battery Jumper Manual de usuario

Wagan

Wagan 7004 Manual de usuario

Wagan

Wagan JUMPER 9796 Manual de usuario

Wagan

Wagan 2 Way Jumpstarter Manual de usuario

Wagan

Wagan iOnBoost SLIM Manual de usuario

Wagan

Wagan 2412 Manual de usuario

Wagan

Wagan iOnBoost V8 Torque Manual de usuario

Wagan

Wagan iOnBoost V8 Air Manual de usuario

Wagan

Wagan iOnBoosr V8 Manual de usuario

Wagan

Wagan 2467 Manual de usuario

Wagan

Wagan iOnBoost V8 Manual de usuario

Wagan

Wagan iOnBoost v10 Manual de usuario

Wagan

Wagan iOnBoost V6 Manual de usuario

Wagan

Wagan Power Dome NX Manual de usuario

Wagan

Wagan 2045 Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Code Alarm

Code Alarm CA-535 Manual de usuario

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual