Voscom VOS-1110FFDT Series Manual de usuario

VOS-1110FFDT/R series

1-Channel Video + 1 Simplex Audio + 1 Duplex Data

Installation Manual

Fiber Optic Transmission Systems

VOSCOM TECHNOLOGIES CO.,LIMITED

WWW.VOSCOM.COM

Important Safety Instructions EN_1

1. Readthese instructions. Keep these instructions. Heed allwarnings. Follow all instructions.

5. Donot use this apparatus near water. Cleanonly with dry cloth.

7. Donot block any ventilation openings. Install in accordance with the manufacturers

instructions.

8. Donot install near any heat sources such as radiators, heatregisters, stoves,or other

apparatus (includingamplifiers) that produce heat.

9. Donot defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has twoblades withone wider than the other. Agrounding type plug has two blades and a third

grounding prong. The wideblade or the third prong are provided for your safety. Ifthe provided

plug doesnot fitinto your outlet consult an electrician for replacement of the obsolete outlet.

10. Protectthe power cord from being walked on or pinched particularly at plugs,convenience

receptacles, andthe points where they exit from the apparatus.

13. Referall servicingto qualifiedservice personnel. Servicing is required when the apparatus

has beendamaged in any way, suchas power-supply cord or plug is damaged, liquid has been

spilled or objects havefallen into the apparatus,the apparatushas been exposed to rain or

moisture, doesnot operatenormally,or has been dropped.

14. Apparatusshall not be exposed to dripping or splashing and that no objects filled with liquids,

such asvases shall be placed on the apparatus.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatusto rain or

moisture.

16. Installation should be done only by qualified personnel and conform to all local codes.

20. CAUTION: These servicing instructions arefor useby qualified service personnel only.To

reduce therisk of electric shock do not perform any servicing other than that contained in the

operating instructionsunless youare qualifiedto do so.

Website:www.voscom.com

Product Overview En_2

Video

The VOS-1110FFDT/R can transmission1-Channel

video, 1simplex analog auido and 1 duplex data over

singlemode or multimode optical cable.

Stand-alone orrack-mount. The cards can be inserted

into our 14 slots,19inch 4U or 6U rack-mountable

card cage (VOS-CH04 or VOS-CH06).

System Diagram:

Model Number

Transmitter Receiver Fiber Mode Wavelengths Optical

Power

Budget

Maximum

Transmission

Distance

Multi-Mode 1310nm/1550nmVOS-1110FFDMRVOS-1110FFDMT

•The OpticalPower Budgetdata fitMulit-mode(62.5/125 m),Single-Mode(9/125 m).

•When using50/125 m multimode fiber, subtract3 dBfrom the optical power budget.

•Optical transmissiondistance is limited to optical loss of thefiber and any additional loss introduced by connectors,

splices andpatch panels.

•Maximum transmissiondistance is also limited by fiber bandwidth.

•Power adapteris manufactured by thirdparty and is supplied with fitted screw-terminal outputcables.Power

adapter included(for standalone) US, European, UK or Australian powerplug.

•Please feelfree to consult factory for anyspecial requirement and customization

Note:

16dB 2km

Single-Mode

VOS-1110FFDSRVOS-1110FFDST 12dB 20km

VOS-1110FFDST-4

VOS-1110FFDST-6

VOS-1110FFDSR-4

VOS-1110FFDSR-6

Single-Mode

18dB

25dB

40km

60km

Models and Optical Power Budget:

•Uncompressed Digital Composite Video over onefiber

•Compatible with all PAL,NTSC,SECAM Video Systems

•Multi-mode Fiber Support for Distances up to 2.0 km

•Single-Mode Fiber Support for Distances up to 100 km

•No EMI or RFI and noground loops

•Stand alone or rack-mount

Features:

Audio

1310nm/1550nm

Data

1 Fiber opticCable Monitor

VOS-1110FFDT

Transmitter VOS-1110FFDR

Receiver

1 x Video 1 x Video

1 xAudio 1 xAudio

1x DuplexData 1 x Duplex Data

Fiber OpticConnector, FC/PC or ST/PC

BNC Connector, 75-ohm analog videoinput (Transmitter)/output (Receiver)

Stand-alone Power supply Connector, DC5V2A Input.

Panel & Cable Connection En_3

NOTE1: Digital video optic transmitterand receivershould be used in pairs, one is Transmitter

(LED is red), theother is Receiver (LED is green).

NOTE2: Avoid simultaneously connecting video signals to both the front BNC andrear BNC of the

same channel.Also, since each video channel is factory terminated to 75 ohm, unused BNCs

should notbe used for loop-through video connections.

4Audio Connector, Terminal Block,analog audio input (Transmitter)/output (Receiver)

DC5V

1 2 3 4

DATA

POWER

OPTIC

EXT

FRONT PANEL

REAR PANEL

EXT2

FTX

EXT1

C+ C- D+D-

None

A+ A- B + B-

5Data Connector, 4 Pin Terminal Block,Data support one duplex Rs485 or Rs232 data.

Transmitter (Rs485): One DuplexRs485 Data Connection (Input/Output)

4 Pin Terminal Block Pin

Conect DataRs485+ (A)

Conect DataRs485- (B)

None

Input/Output

1 2 3 4

DATA 1

Input/Output

Conect Ground(GND)

Input/Output

Panel & Cable Connection En_4

Receiver (Rs485):One Duplex Rs485 Data Connection (Input/Output)

Transmitter (Rs232):One Duplex Rs232 Data Connection (Input/Output)

Receiver (Rs232):One Duplex Rs232 Data Connection (Input/Output)

Note: If you need the Rs422 or RS485(4-wire) data connection,

please contact us, [email protected].

4 Pin Terminal Block Pin

Conect DataRs485+ (A)

Conect DataRs485- (B)

None

Input/Output

1 2 3 4

DATA 1

Input/Output

Conect Ground(GND)

Input/Output

4 Pin Terminal Block Pin

Conect DataRs232 RXD

Conect DataRs232 TXD

None

Input/Output

1 2 3 4

DATA 1

Input/Output

Conect Ground(GND)

Input/Output

4 Pin Terminal Block Pin

Conect DataRs232 RXD

Conect DataRs232 TXD

None

Input/Output

1 2 3 4

DATA 1

Input/Output

Conect Ground(GND)

Input/Output

Panel & Cable Connection En_5

8 Pin Terminal Block

A+

A-

B+

B-

C+

C-

D+

D-

None

Connect Audio1

Connect GND1

None

8 Pin Terminal Block

A+

A-

B+

B-

C+

C-

D+

D-

Connect Audio1

None

Connect GND1

None

C+ C- D+ D-A+ A- B+ B-

Receiver (Audio): 1-Channel Simplex Audio Connection (Output)

Transmitter (Audio): 1-Channel Simplex Audio Connection (Input)

Input

Output

NOTE: AUDIO SIGNAL AND IMPEDANCE MODE

1) Audio Signal: The audiois Mono Audio in default, can support Stereo audio, but you

should consultfor us before the order.

2) Impedance Mode: The audio is unbalanced mode in default, can support 600 ohm

balanced audio, but you should consult for us before the order

Website:www.voscom.com

Stand-alone Installation En_6

The VOS-1110FFDTtransmitter/VOS-1110FFDR receiver can be mounted into a rack orcan be

used asa stand-alone module. As a stand-alonemodule, the unit can be placed on a desktop or

can bemounted to a wall.

NOTE: Before mountingthe VOS-1110FFDTtransmitter/VOS-1110FFDR receiver, please ensure

that thereis adequate space at both ends for viewing the front-panelLEDs and for making the

various rear-panelcable connections.

Website:www.voscom.comWebsite:www.voscom.com

Stand-alone Mounting Size: 142mm x 107mm x 25mm

Rack-mount Installation En_7

Installation Instructions

Typical Configurations:

1:Install the video card into a standard 19inch rack, usinguser-supplied rack-mounting

hardware. Becareful to not damage exposed objects on the back of the card cage unit.

2:If asecondary earth ground connectionis needed, a grounded wire with a ground lug can be

attached to the rackusing the protruding screw provided on the right side of the chassis.

3:If desired, blank panels may beinstalled to cover unused slots. A single blank panel coversa

single slot opening.

4:Each fiber optic plug-in module is equipped with a POWER LED indicator that illuminates

when power is applied to the rack unit.

5:Fiber optic plug-in modules(video cards) can be installed into anyof theavailable 14slots

of thecard cage. Most modules require onlya single slot width, but others, such as the 8-Ch

video Series, require two slot widths.

VOS-CH04:

19 inch4U,14 video card slots, suit for 1-ch,2-ch,4-ch,8-ch(two slots)video cards.

Support oneslide-in power supply AC100V~AC240V

VOS-CH06:

19 inch6U,16 video card slots, suit for 1-ch,2-ch,4-ch,8-ch(two slots)video cards.

Support two slide-in power supply AC100V~AC240V, one for redundancy.

Website:www.voscom.com

The VOS-1110FFDTtransmitter/VOS-1110FFDR receivercan beinstalled into our rack mount

chassis,VOS-CH04 orVOS-CH06, whichcan be mounted into an industry-standard 19-inch

equipment rack.

Troubleshooting En_8

Indicator Status Meaning Possible Cause Corrective Action

Power LED

Light Power isbeing applied

to the module. --- No actionrequired.

Not Light Power isnot being

applied to the module.

Check powerconnection.

If moduleis rackmounted,

reseat moduleor power

supply asnecessary.

Power connectionis

faulty.

Power supplyhas failed. Replace powersupply.

Loss ofpower occurs due

to trippedcircuit

breaker(s), blownfuse(s),

or faultyelectrical

service.

Check circuit breaker(s),

fuse(s), orelectrical

service asnecessary.

LED indicators on thefront-panel of the transmitter/receiverallow youto monitor signal status,

laser status,data activity, contact closure activation, and operatingpower. Table A~D provide

information aboutthe front-panelindicators and associated troubleshooting guidelines.

Table A: Power Links

Indicator Status Meaning Possible Cause Corrective Action

Video LED(VIDEO 1,VIDEO 2....)

Light Incoming video signal

is present on thechannel. --- No actionrequired.

Not Light

on Transmitter Incoming video signal

is not present on the

channel.

Check power connection

to the video source.

Video source is not

powered on.

Video source is not

connected to the

transmitter.

Check BNC connections.

Coaxial cable is

defective. Replace cable.

Table B: Video Links

Not Light

on Receiver Incoming video signal

is not present on the

channel.

Optical signal is not

being receivedfrom the

transmitter. Optic Fault

LED is also not light.

Refer tothe Optic Fault

LED section in this table.

Video source is not

powered on. Check power connection

to the video source.

Video source is not

connected to the

transmitter.

Check BNC connections.

Coaxial cable connected

to the transmitter is

defective.

Replace cable.

Website:www.voscom.com

Troubleshooting En_9

Indicator Status Meaning Possible Cause Corrective Action

Data(RS485/RS232/RS422) LED

Flashing

Data is being transmitted

onto the fiber by the data

port or is being received

from thefiber by the

data port.

--- No actionrequired.

Table C: Data Links

Indicator Status Meaning Possible Cause Corrective Action

Optic LED

Light The optical signal is being

received andlaser is

operatingproperly.

--- No actionrequired.

Not Light

Table B: Optic Links

Not Light

Data isnot being

transmitted ontothe

fiber bythe data port or

is notbeing received

from thefiber by the

data port.

Data isnot present on

the channel. No actionrequired.

Data connectionis faulty. Check dataconnections.

Data communication

cable isdefective. Replace cable.

The optical signal is

not beingreceived.

Remote fibermodule is

not poweredon. Check power connections.

Replace powersupply if

necessary.

Fiber optic cable is not

connected. Check fiberoptic

connections.

Fiber optic cable

connectors aredirty or

are damaged.

Clean, polish, or replace

fiber opticcable

connectors asnecessary.

Fiber optic cable is

defective. Replace cable.

A problemexists with

the optical power

budget.

Verify thatlosses in fiber

optic cable do not exceed

the optical power budget

specification of the fiber

optic link. If the losses do

exceed theoptical power

budget, contactProduct

Support.

Website:www.voscom.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Receptor de Voscom

Voscom

Voscom VOS-1FOM-SCCT Series Manual de usuario

Voscom

Voscom VOS-2200FFT Series Manual de usuario

Voscom

Voscom VOS-1DH3G-ADCEMT Manual de usuario

Voscom

Voscom VOS-1210FFDT Series Manual de usuario

Voscom

Voscom VOS-8040FDT Series Manual de usuario

Voscom

Voscom VOS-2210FFDT Series Manual de usuario

Voscom

Voscom VOS-8810FFDT Series Manual de usuario

Voscom

Voscom VOS-1HD-ADST Manual de usuario

Voscom

Voscom VOS-1200FFT Series Manual de usuario

Voscom

Voscom VOS-8FOM-D485T Series Manual de usuario

Voscom

Voscom VOS-0200FT Series Manual de usuario

Voscom

Voscom VOS-0200DT Series Manual de usuario

Voscom

Voscom VOS-4000FT Series Manual de usuario

Voscom

Voscom VOS-1DHD-ADMT Manual de usuario

Voscom

Voscom VOS-2FOM-D485T Series Manual de usuario

Voscom

Voscom VOS-1HD-ADCET/R Series Manual de usuario

Voscom

Voscom VOS-4800FFT Series Manual de usuario

Voscom

Voscom VOS-2410FFDT Series Manual de usuario

Voscom

Voscom VOS-2H3G-ADCEMT Manual de usuario

Voscom

Voscom VOS-8FOM-D232T Series Manual de usuario

Voscom

Voscom VOS-0400DT Series Manual de usuario

Voscom

Voscom VOS-4400FFSeries Manual de usuario

Voscom

Voscom VOS-16010FBT Series Manual de usuario

Voscom

Voscom VOS-2400FFT Series Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario