Vonets VAP11S Instrucciones de uso
VONETS——WiFi Bridge/Repeater/Router
WiFi Bridge/Repeater/Router
VAP11S/VAP11S-5G
Quick Setting Guide
VONETS——WiFi Bridge/Repeater/Router
Declaration
Copyright © 2019 Shenzhen HouTian Network Communication Technology Co.,Ltd
All rights reserved, with retained ownership Without Shenzhen HouTian Network
communication Technology Co.,Ltd written authorization, any company or personal can’t
copy, writer or translation part or all contents. Can’t do commodity distribution for any
commercial or profitable purposes by any ways(electricity, mechanical, photoprint, record or
other methods).
VONETS is the registered trademark of Shenzhen HouTian Network Communication
Technology Co.,Ltd. The other all trademarks or registered trademarks mentioned in this
documents are belong to the individual owners. The product specifications and information
technology mentioned in this manual are just for reference, if any updates, without other not
ice. Except for special agreements, this manual is just for user guidance, any statements, in
formation and so on in this manual can’t constitute the warranty of any forms.
Note
The parameters used in the screenshots shown in this manual are only used as reference
examples for setting examples. They may not be exactly the same as the actual situation.
Please set the parameters according to your actual needs.
Due to the different software versions, the screenshots shown in this manual may not be
exactly the same as the web interface of the product you purchased. Please configure your
product according to the actual web interface.
This manual applies to both VAP11S and VAP11S-5G products. The“VONETS device”
mentioned in the text can refer to these two products.
Form 1
Transmission Distance Parameters Form
Model
No-barrier point to point
Transmission Distance
Transmission Rate
(Mbps)
Band
VAP11S
400m--500m
300
2.4G
VAP11S-5G
400m--500m
900
5G
Form 2
Power Supply Parameters List
Model
Power Supply
Voltage
Input Power
Typical Power Supply
VAP11S
DC5--24V
≥10W
5V/2A
VAP11S-5G
DC5--24V
≥10W
5V/2A
VONETS——WiFi Bridge/Repeater/Router
Contents
Chapter 1 Application Mode.......................................................................................................................................... 1
1.1 Bridge + Repeater Mode...................................................................................................................................... 1
1.2 Router Mode............................................................................................................................................................... 2
Chapter 2 Bridge+Repeater Mode Configuration Instruction................................................................... 3
2.1 Device connect......................................................................................................................................................... 3
2.2 Bridge+Repeater Application Configuration ............................................................................................ 3
2.3 AP Application Configuration...................................................................................................................... 6
Chapter 3 Router Mode Configuration Instruction............................................................................................ 8
3.1 Change device mode........................................................................................................................................ 8
3.2 WAN port settings................................................................................................................................................... 9
3.2.1 WAN/LAN exchange...................................................................................................................................... 9
3.2.2 WAN Port connection method ............................................................................................................... 10
3.2.3 WAN port wired connect network——DHCP.................................................................................. 10
3.2.4 PPPoE WAN port wired connect network——PPPoE................................................................ 11
3.2.5 WAN port wireless connect network---- WiFi................................................................................. 11
3.3 Set WiFi hotspot parameters........................................................................................................................... 13
Chapter 4 Other components and installation method................................................................................. 15
4.1 Other components................................................................................................................................................ 15
4.2 Industrial chassis rail hook kit installation.............................................................................................. 15
4.3 Ethernet port expander installation............................................................................................................. 16
Appendix Frequently Asked Questions................................................................................................................. 17
VONETS——WiFi Bridge/Repeater/Router
1
Chapter 1 Application Mode
1.1 Bridge + Repeater Mode
There are three application modes for the bridge mode of VONETS device: WiFi repeater,
WiFi bridge and WiFi AP.
⚫WiFi Repeater:
VONETS device as WiFi Repeater, it must be configured to source WiFi hostpot
parameters, can be used to extend the wireless signal coverage of existing APs or wifi
router .
⚫WiFi Bridge:
VONETS device as WiFi bridge, it must be configured to source WiFi hotspot
parameters, can be used for devices only with Ethernet ports to access wireless
networks.
⚫WiFi AP：
VONETS device as WiFi AP, it can achieve wireless access to wired LAN, no
configuration required, plug and play.
VONETS——WiFi Bridge/Repeater/Router
2
1.2 Router Mode
⚫VONETS device as WiFi router, the Ethernet port of VONETS device defaults to WAN
port, the Ethernet cable defaults to the LAN port. WAN and LAN ports are
interchangeable.
⚫VONETS device is used as WiFi router, WAN port can be set to connect to the WiFi
hotspot for use as a secondary router, its Ethernet port and Ethernet cable both are LAN
port;
VONETS——WiFi Bridge/Repeater/Router
3
Chapter 2 Bridge+Repeater Mode Configuration
Instruction
2.1 Device connect
Power on VONETS device by 5V/2A power supply, then connect to PC, there are two
connection ways as below:
A. Computer is wired connected to LAN port of VONETS device;
（Recommend Method）
B. The computer wirelessly connects to the WiFi signal of VONETS device, its default
hotspot parameters are as follows:
Model
WiFi SSID
WiFi Password
VAP11S
VONETS_2.4G_****
12345678
VAP11S-5G
VONETS_5G_****
12345678
（After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.）
2.2 Bridge+Repeater Application Configuration
The configuration steps of VONETS device for WiFi repeater and WiFi bridge are basically
the same, so this manual combines the configuration instructions of the two application
VONETS——WiFi Bridge/Repeater/Router
4
modes.
1. After computer is connected to VONETS device, open browser, input configured page:
http://vonets.cfg (or IP: 192.168.254.254), then press Enter;
2. Input User name and Password in login page (both are “admin”), click “Login” button to
enter configured page;
3. “Scan Hotspots”, choose the source hotspots, click “Next”;
4. Input “Source wireless hotspot password”, click “Apply”;
⚫IP layer transparent transmission (factory default), transparent transmission of IP
layer data, can meet most of WiFi bridge applications;
⚫MAC layer transparent transmission, transparent transmission of all data above the
MAC layer (link layer) and MAC layer, including IP layer data. MAC transparent
transmission can solve some special applications for MAC layer encryption, such as
GoPro camera, CiscoAP, Hikvision monitoring system, etc;
⚫The option “The configuration parameters of WiFi repeater security is
synchronized with source hotspot” is default ticked, it means the SSID of VONETS
repeater is associated with the SSID of the source hotspot, and the WiFi password is the
same as the password of the source hotspot;
⚫Disable hotspot, if you select “Disable hotspot” on the right side of the SSID, the device
VONETS——WiFi Bridge/Repeater/Router
5
will not transmit the corresponding hotspot and can only be used as a bridge application;
⚫Advanced Setting,include Hot spot authentication match mode, WiFi Signal Motion
Detection and SSA Signal strength alarm threshold,these options here can be kept
unchanged, for instructions on this option, go to www.vonets.com and download the “V
Series WiFi Bridge Advanced Features Instruction”;
5. Click “Reboot”, VONETS device will connect to the configured WiFi hotspot automatically,
if connection is successful, the WiFi LED light will flash quickly;
Remark 1:
LED Light Form
Model
Blue Light
Green Light
Yellow Light
VAP11S
WiFi Connection
Status Light
/
Ethernet Cable Connection
Status Light
VAP11S-5G
System Status Light
WiFi Connection Status
Light
①VONETS device is not connected to any hotspot, WiFi connection status light will flash
quickly;
VONETS——WiFi Bridge/Repeater/Router
6
②VONETS device is connected to hotspot successfully, but hotspot signal strength is
greater than 50%, WiFi connection status light will quick flash;
③VONETS device is connected to hotspot successfully, but hotspot signal strength is less
than 50% greater than 10%, WiFi status light will pause flash and flash;
④VONETS device is connected to hotspot failed, WiFi connection status light will flash
slowly.
2.3AP Application Configuration
VONETS device can be configured as an AP application, the wireless terminal device can
connect to VONETS device hotspot to connect to the network; however, it is best to change
its WiFi name and password for network security.
1. Log in to the configuration page http://vonets.cfg (or IP: 192.168.254.254you’re your
computer browser, both user name and password are “admin”;
2. Revise WiFi name: Jump to “WiFi Repeater”---- “Basic Settings”, enter new WiFi name
in “General Hotspot SSID”, click “Apply”;
3. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi password
in “Pass Phrase”, click “Apply”;
VONETS——WiFi Bridge/Repeater/Router
7
4. “WiFi Tx Power” of VONETS device can be changed, jump to “System Settings”----
“Advance Settings”, choose suitable transmit power, then click “Apply”;
5. Reboot device, jump to “System Settings”---- “Reboot Device”, click “Reboot”, when it is
finished, all revised options will take effort.
Remark 2: When VONETS device connects to external network, its IP address will be
changed. At this time, when log in configured page, we suggest you enter configured domain
name: http://vonets.cfg. Or in Windows command window, enter the command: ping
vonets.cfg, to get the IP address of the device, then log in configuration page by this IP
address.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de Vonets
Vonets
Vonets VAP11N-300 Instrucciones de uso
Vonets
Vonets VAP11N Instrucciones de uso
Vonets
Vonets VAP11N Instrucciones de uso
Vonets
Vonets VAP11G Manual de usuario
Vonets
Vonets VAP11S-232 Instrucciones de uso
Vonets
Vonets VAP11G Manual de usuario
Vonets
Vonets VGA1000 Instrucciones de uso
Vonets
Vonets VAP11G Manual de usuario
